TP-Link TL-WR902AC TL-WR902ACUS V3 Quick Installation Guide

TP-Link TL-WR902AC Manual

Get TP-Link TL-WR902AC PDF manuals and user guides View all TP-Link TL-WR902AC manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-WR902AC manual content summary:

  • TP-Link TL-WR902AC | TL-WR902ACUS V3 Quick Installation Guide - Page 1
    Guide AC750 Wi-Fi Travel Router TL-WR902AC Need setup video? Scan the QR code, or visit https://www.tp-link.com/download/TL-WR902AC.html#videos 7106508201 REV3.0.1 Determine Operation Mode Refer to the following scenarios to determine an appropriate operation mode. Scenario During Travel
  • TP-Link TL-WR902AC | TL-WR902ACUS V3 Quick Installation Guide - Page 2
    web instructions to set up the internet connection. Notes: You can customize your Network Name and Password for the 2.4GHz/5GHz wireless network during the Quick Setup, but you need to reconnect your wireless devices to the new Wi-Fi network(s). If you are not sure about the LAN Type of the router
  • 1
  • 2
Refer to the following scenarios to determine an appropriate operation mode.
7106508201
REV3.0.1
Determine Operation Mode
AC750 Wi-Fi Travel Router
Quick Installation Guide
TL-WR902AC
Hardware Information
Blinking
WPS connection is in progress.
No WPS connection is established.
This light stays on for 5 minutes when a WPS
connection is established, then goes off.
Indication
Status
LED
On/Off
On/Off
On
Blinking
Off
Blinking
(Power)
(Internet)
(Wireless)
(USB)
(WPS)
On
On
Off
Off
The router is on or off.
The internet is available or unavailable.
Blinking
The WAN/LAN
port is connected but internet is
unavailable when in Router or Access Point mode.
The wireless network is enabled.
The wireless network is disabled.
The router is connecting to the host network
when in Range Extender or Client mode.
A USB device is connected.
No USB device is connected.
The router is initializing or being upgraded.
(WPS Button)
Description
Item
Mode Switch
WAN/LAN Port
POWER Port
RESET Button
3G/4G USB Port
The port is used to connect the power adapter.
This port functions as the WAN port in Router
mode and as the LAN port in Hotspot, Range
Extender and Client modes. This port is for
connecting to the existinig router in Access
Point mode.
To reset the router, use a pin to press and hold
the button until all the LEDs turn off.
This port is used for plugging in a 3G/4G
modem or USB drive.
To establish WPS connection, press this button.
This switch is used to change the operation
mode of the router.
Need setup video?
Scan the QR code, or visit
During Travel
Router Mode
Hotspot
Mode
Internet
B
C
D
A
Wired Network
A
B
Public Hotspot
1.
Switch the Mode Switch to
Share ETH
and connect the hardware from Step
A
to
D.
Tip: If you are using a 3G/4G USB modem with a SIM/UIM card, plug the USB modem into the 3G/4G USB port
to transfer the 3G/4G signal to Wi-Fi.
2.4G: TP-Link_XXXX
5G: TP-Link_XXXX_5G
SSID
XXXXXXXX
Wireless
Password
/PIN
2.
Connect your device to the router’s Wi-Fi
.
The default SSID (network name) and
Wireless Password are printed on the label at the back of the router.
2.4G: TP-Link_XXXX
5G: TP-Link_XXXX_5G
SSID
XXXXXXXX
Wireless
Password
/PIN
2.
Connect your device to the router wirelessly or via an Ethernet cable
.
The default SSID
(network name) and Wireless Password are printed on the label at the back of the router.
5.
Click
Next
to start the Quick Setup and then follow the step-by-step web instructions
to set up the internet connection.
Notes:
If you are not sure about your
WAN Connection Type
, click
Auto Detect
.
You can customize your
Wireless
Network Name
and
Password
for the 2.4GHz/5GHz wireless network during
the Quick Setup
,
but you need to reconnect your wireless devices to the new Wi-Fi network(s).
3.
Check whether the Internet LED
is on.
- If yes, skip to Step 6.
- If no, continue with the steps below.
4.
Launch a web browser and enter
http://tplinkwifi.net
in the address bar.
Log in with
admin
(in lowercase) for both username and password.
http://tplinkwifi.net
admin
admin
Log In
3.
Launch a web browser and enter
http://tplinkwifi.net
in the address bar.
Log in with
admin
(in lowercase) for both username and password.
4.
Click
Next
to start the Quick Setup and then follow the step-by-step web instructions
to set up the internet connection.
Notes:
If you are not sure about your
WAN Connection Type
, use
Dynamic IP
in most cases or consult the ISP.
You can customize your
Local
Network SSID
and
Password
for the 2.4GHz/5GHz wireless network during the
Quick Setup, but you need to reconnect your wireless devices to the new Wi-Fi network(s).
http://tplinkwifi.net
admin
admin
Log In
1.
Switch the Mode Switch to
Share Hotspot
and connect the hardware from Step
A
to
B
.
6.
Connect your own devices to the router’s Wi-Fi to enjoy the internet. The WAN/LAN
port functions as the WAN port in this mode.
Scenario
Router (Default Mode)
Operation Mode
Hotspot
Access Point
Range Extender
Client
Share ETH
Mode Switch
Share Hotspot
AP/Rng Ext/Client
The wired network is only limited to one device to connect at a
time and I want to share the internet with more wireless devices.
I Want To...
I want to turn existing public Wi-Fi into a private network (wired and
wireless).
I am in a Wi-Fi "dead zone" or a place with weak wireless signal. I want
to expand an existing Wi-Fi network for a better internet connection.
I have a wired-only device, for example, a smart TV, media player, or
game console. I want to connect it to a Wi-Fi network.
I want to turn the existing wired-only network into a wireless network.
During Travel
At Home
5.
Connect your own device to the router wirelessly or via an Ethernet cable to enjoy the
internet. The WAN/LAN port functions as the LAN port in this mode.