TRENDnet TEG-S224TXA Manual

TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100 2-10/100/1000 Manual

Get TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100 2-10/100/1000 PDF manuals and user guides
UPC - 710931501254
View all TRENDnet TEG-S224TXA manuals
Add to My Manuals
Save this manual to your list of manuals

TRENDnet TEG-S224TXA manual content summary:

  • TRENDnet TEG-S224TXA | Manual - Page 1
    TEG-S224TXA 26-Port 10/100/1000Mbps Smart Copper Gigabit Switch with 2×1000BASE-T + 24×10/100BASE-TX ports User's Guide
  • TRENDnet TEG-S224TXA | Manual - Page 2
  • TRENDnet TEG-S224TXA | Manual - Page 3
    . This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in
  • TRENDnet TEG-S224TXA | Manual - Page 4
    UL Warning a) Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible
  • TRENDnet TEG-S224TXA | Manual - Page 5
    TABLE OF CONTENTS ABOUT THIS GUIDE 1 PURPOSE 1 TERMS/USAGE 1 INTRODUCTION 3 FAST ETHERNETTECHNOLOGY 3 GIGABIT ETHERNETTECHNOLOGY 4 SWITCHING TECHNOLOGY 5 VLAN (VIRTUAL LOCAL AREA NETWORK 6 FEATURES 7 UNPACKING AND INSTALLATION 9 UNPACKING 9 INSTALLATION 10 RACK MOUNTING 11
  • TRENDnet TEG-S224TXA | Manual - Page 6
    PORTS 1~24 STATUSLEDS 20 PORT 25 & PORT 26 STATUS LEDS 20 CONFIGURING THE SWITCH 23 CONFIGURATION VIA SERIAL PORT 23 SETTING THE SWITCH 24 MAIN MENU 25 CONFIGURING SETUP SETTING 25 CONFIGURING SYSTEM SETTING 30 CONFIGURING FILE SETTING 31 TECHNICAL SPECIFICATIONS 33
  • TRENDnet TEG-S224TXA | Manual - Page 7
    Gigabit Ethernet Smart Switch. This device integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet, and 10Mbps Ethernet network capabilities in a highly flexible package. Purpose This guide discusses how to install your 26-Port 10/100/1000Mbps Gigabit Ethernet Smart Switch. Terms/Usage In this
  • TRENDnet TEG-S224TXA | Manual - Page 8
  • TRENDnet TEG-S224TXA | Manual - Page 9
    INTRODUCTION This chapter describes the features of the Switch and some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching and VLAN technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are
  • TRENDnet TEG-S224TXA | Manual - Page 10
    Ethernet can greatly improve network response times as well as significantly speed up the traffic between your subnets. Gigabit Ethernet supports video conferencing, complex imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet
  • TRENDnet TEG-S224TXA | Manual - Page 11
    technologies. And with expected advances in silicon technology and digital signal processing, Gigabit Ethernet will eventually operate over unshielded twisted-pair (UTP) cabling, outfitting your network with a powerful 1000-Mbps-capable backbone /server connection creating a flexible foundation for
  • TRENDnet TEG-S224TXA | Manual - Page 12
    , the setup and maintenance required make routers relatively impractical. Today switches are an ideal solution to most kinds of local area network congestion problems. VLAN (Virtual Local Area Network) A VLAN is a group of end-stations that are not constrained by their physical location and can
  • TRENDnet TEG-S224TXA | Manual - Page 13
    ?? Extensive front-panel diagnostic LEDs ?? IEEE 802.3x flow control for full-duplex ?? Back pressure flow control for half-duplex ?? Supports Port-based VLAN ?? Supports Port-based QoS ?? RS-232 DCE console port for setting up and managing the Switch via connection to a console terminal or PC
  • TRENDnet TEG-S224TXA | Manual - Page 14
  • TRENDnet TEG-S224TXA | Manual - Page 15
    power connections ?? One console cable (RS-232: 9 pin female to 9 pin female) ?? Four rubber feet for shock cushioning ?? Screws and two mounting brackets ?? This User's Guide If any item is found missing or damaged, please contact your local reseller for replacement. 9
  • TRENDnet TEG-S224TXA | Manual - Page 16
    exposure to sunlight. Leave at least 10cm of space around the Switch for ventilation. Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, Rack Mounting. When installing
  • TRENDnet TEG-S224TXA | Manual - Page 17
    Figure 1. Attach the adhesive rubber pads to the bottom Rack Mounting The Switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipments. Attach the mounting brackets to both sides of the Switch (one at each side), and secure them with the
  • TRENDnet TEG-S224TXA | Manual - Page 18
    Switch to the rack. Figure 3. Installing the Switch on an equipment rack Connecting Network Cable The Switch supports 24 10/100Mbps Fast Ethernet ports and 2 10/100/1000Mbps Gigabit Ethernet ports. It runs full/half duplex transfer mode for 10/100Mbps speed and
  • TRENDnet TEG-S224TXA | Manual - Page 19
    AC Power The Switch can be used with AC power supply 100~240V AC, 50~60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The Switch's power supply will adjust to the local power source automatically and may be turned on without having any
  • TRENDnet TEG-S224TXA | Manual - Page 20
  • TRENDnet TEG-S224TXA | Manual - Page 21
    network speeds of either 10Mbps or 100Mbps, and can operate in half- or full- duplex transfer modes. These ports also support Auto-MDIX crossover detection function, providing true "plug and play" capability. 1000BASE-T Twisted Pair Ports (Port 25~26) The Switch is equipped with two Gigabit
  • TRENDnet TEG-S224TXA | Manual - Page 22
    emulation program. Rear Panel Power Switch Power Connector Figure 5. The rear panel of the Switch AC Power Connector This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet
  • TRENDnet TEG-S224TXA | Manual - Page 23
    UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. Figure 6. LED indicators of the Switch Device LED POWER On : When the Power LED lights on, the Switch is receiving power. Off : The
  • TRENDnet TEG-S224TXA | Manual - Page 24
    Ports 1~24 Status LEDs LINK/ACT On : When the LED lights on, the respective port is connected to the 10/100Mbps Ethernet network. Blinking : When the LED is blinking, the port is transmitting or receiving data on the 10/100Mbps Ethernet network. Off : No link. 100Mbps On : When the LED
  • TRENDnet TEG-S224TXA | Manual - Page 25
    1000Mbps On : When the LED lights on, the respective port is connected to a Gigabit Ethernet network. Off : When the LED is off, the respective port is connected to a 10/100Mbps Ethernet network. 100Mbps On : When the LED lights on, the respective port is connected to a 100Mbps Fast
  • TRENDnet TEG-S224TXA | Manual - Page 26
  • TRENDnet TEG-S224TXA | Manual - Page 27
    CONFIGURING THE SWITCH This Switch is a "Smart" switch. The programmable administration parameters allow the Switch to operate more effectively than unmanaged (dumb) switches. This chapter will describe how to configure the Switch. Configuration via Serial Port The Switch is accessible using a
  • TRENDnet TEG-S224TXA | Manual - Page 28
    Setting the Switch The 26-Port 10/100/1000Mbps Gigabit Ethernet Smart Switch has a menu-driven console interface for smart switch configuration. The Switch can be configured through the serial port. A network administrator can manage and control the Switch from the console program. This section
  • TRENDnet TEG-S224TXA | Manual - Page 29
    Main Menu The main menu appears, as shown in Figure 7. You can see the available console command keys in the lower portion of the screen. Move cursor to highlight a desired option by using Tab key and then press Enter key to confirm. There are five options: Setup, System, File, Save and Exit Setup
  • TRENDnet TEG-S224TXA | Manual - Page 30
    Figure 8. Setup Port Configuration In the Port Configuration menu, you can configure each port's Speed, Flow Control, and QoS (port 1 ~ port 26) (see Figure 9). This screen displays Port 01 ~ 12 status; for port 13 ~ 26, use the [DOWN/TAB] key to select Next. After completing the setup, move cursor
  • TRENDnet TEG-S224TXA | Manual - Page 31
    Figure 9. Port Configuration (1) Speed The speed for all parts can only work at Auto Mode. (2) Flow Control This setting determines whether or not the Switch will be handling flow control. To change the flow control setting, select the Port number, highlight the FlowCtrl field, and hit Space Bar to
  • TRENDnet TEG-S224TXA | Manual - Page 32
    Quality of Service (QoS) is a networking term that specifies a guaranteed throughput level. When data packets with QoS priority information pass through QoS supported device, these packets will be handled with priority. Without certain level of QoS, multimedia applications such as Streaming Video
  • TRENDnet TEG-S224TXA | Manual - Page 33
    port and then hit [Space Bar] to select "V" to add the port to the VLAN group or select "-" to delete the port from the group. By default, all ports belong to VLAN 1. The default setting of VLAN is shown as Figure 10. Figure 10. VLAN Configuration For example, there are five computers (PC1~PC5)
  • TRENDnet TEG-S224TXA | Manual - Page 34
    VLAN1 1 2 3 4 X VLAN2 2 3 4 5 Figure 11: Dividing the Switch into two smaller switches Note: Configuring VLAN can be very confusing. If your VLAN settings do not perform the way they should, you can reset the Switch back to its default state by going to "System" menu and select "Factory
  • TRENDnet TEG-S224TXA | Manual - Page 35
    ?? Figure 12. System Setting Configuring File Setting The File Configuration Menu screen (shown in Figure 13) indicates the following information: Upload Configuration: Select this for saving the current configuration to a file at a desired location (e.g. floppy disk or hard drive). ?? Move cursor
  • TRENDnet TEG-S224TXA | Manual - Page 36
    ?? At "Are you sure?" hit "space bar" once to show "Yes" and then hit "Enter". ?? On Hyper Terminal's Menu Bar, click on "Transfer" and select "Receive File...". ?? Input the path where you would like to save the file to (or click on "Browse" to select the location), click on the drop down arrow and
  • TRENDnet TEG-S224TXA | Manual - Page 37
    After loading the configuration file, the cursor will move to "Exit", hit "Enter" to go back to "File" menu. Figure 13. File installation 33
  • TRENDnet TEG-S224TXA | Manual - Page 38
  • TRENDnet TEG-S224TXA | Manual - Page 39
    TECHNICAL SPECIFICATIONS Standards Protocol Data Transfer Rate Topology Network Cables Number of Ports General IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100 BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet CSMA/CD Ethernet: 10Mbps (half duplex), 20Mbps (full duplex) Fast Ethernet:
  • TRENDnet TEG-S224TXA | Manual - Page 40
    Physical and Environmental AC inputs: Power Consumption: Temperature: Humidity: Dimensions: Emissions: 100-240V AC, 50/60 Hz internal universal power supply 20 watts. (max.) Operating: 0?~40?C (32?~104?F), Storage: -10?~70?C (14?~158?F) Operating: 10%~90%, Storage: 5%~90% 440 × 200× 44 mm (17.32 x
  • TRENDnet TEG-S224TXA | Manual - Page 41
    35
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
TEG-S224TXA
26-Port 10/100/1000Mbps
Smart Copper Gigabit Switch
with
2×1000BASE-T + 24×10/100BASE-TX ports
User’s Guide