TRENDnet TEW-410APB Manual
TRENDnet TEW-410APB Manual
 |
View all TRENDnet TEW-410APB manuals
Add to My Manuals
Save this manual to your list of manuals |
TRENDnet TEW-410APB manual content summary:
- TRENDnet TEW-410APB | Manual - Page 1
TEW-410APB Wireless 802.11g AP User's Manual Version 1.4 User's Guide 0 - TRENDnet TEW-410APB | Manual - Page 2
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. July. 2003 User's Guide 1 - TRENDnet TEW-410APB | Manual - Page 3
4 3. Hardware Installation 5 4 Web Management Settings 6 4.1. Primary Setup ...7 4.2. System...11 4.3. Operating Mode...12 4.4. Status...14 4.5 Traffic Log...15 4.6 AccessControl ...16 4.7 Advanced Wireless...17 4.8. SNMP...19 4.9. Upgrade Firmware...20 5. Troubleshooting ...22 User's Guide 2 - TRENDnet TEW-410APB | Manual - Page 4
1. Introduction Thank you for purchasing your AP Wireless 802.11g AP. This user guide will assist you with the installation procedure. The package you have received should contain the following items: AP Wireless 802.11g AP User Guide Power Supply / Cord Ethernet Cable Note: if anything is missing, - TRENDnet TEW-410APB | Manual - Page 5
Notification Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Please read the user manual thoroughly electronic components may be damaged by direct sunlight or heat sources. User's Guide 4 - TRENDnet TEW-410APB | Manual - Page 6
Reset Button for approximately ten seconds, all configurations will set to factory default settings. LAN The RJ-45 Ethernet ports used to connect your PC, hub, switch or Ethernet network. AP Default Settings The default settings are shown following. User admin Password admin AP IP Address - TRENDnet TEW-410APB | Manual - Page 7
you must use your web browser and manually input http://192.168.1.250 into the Address box and press Enter. The Main Page will appear. To start configure the Wireless 11g AP, you must login as "admin" in the User Name box. And input password "admin" on the password section. Once you have logged-in - TRENDnet TEW-410APB | Manual - Page 8
be able to configure the AP and get it working properly using the settings on this screen. LAN IP Address and Subnet Mask: This is the AP's IP Address and Subnet Mask as seen on the internal LAN. The default value is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask. User's Guide 7 - TRENDnet TEW-410APB | Manual - Page 9
: This section provide the Wireless Network settings for your WLAN Wireless Settings SSID: The service set identifier ( SSID ) or to be selected. To secure your Wireless Networks, it's strongly recommended to enable this feature. -WEP Make sure that all wireless devices on your network are using - TRENDnet TEW-410APB | Manual - Page 10
that your current Wireless Adapter's driver, and Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft's OS family, only Windows XP has incorporated this by default. The rest of - TRENDnet TEW-410APB | Manual - Page 11
WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and the shared secret from the RADIUS server. WPA Algorithms Radius Server Address RADIUS Server Port RADIUS Shared Key Group Key - TRENDnet TEW-410APB | Manual - Page 12
Defaults feature. Click the Apply button to save the setting. Backup/Restore Setting: Click Backup to store the Access Point's configuration on your local PC. Click Restore to restore Access Point's configuration from your local PC * Check all the settings and click Apply to save them. User - TRENDnet TEW-410APB | Manual - Page 13
4.3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. User's Guide 12 - TRENDnet TEW-410APB | Manual - Page 14
other 802.11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature. Wireless Bridge: This mode allows the connection of one or more remote LANs with a central LAN. * Click Apply to save your settings. User's Guide 13 - TRENDnet TEW-410APB | Manual - Page 15
AP, such as the IP address and the current configuration type. Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and statistics of network traffic. *Click the Refresh button to refresh the AP's status and settings. User's Guide 14 - TRENDnet TEW-410APB | Manual - Page 16
be used. In the Send Log to field, enter the fixed IP address of the PC running the Log viewer software. The AP will send updated logs to that PC. To see a temporary log of the AP's most recent traffic, click the View Log button.. Click the Apply button to save the setting. User's Guide 15 - TRENDnet TEW-410APB | Manual - Page 17
: This function will allow administrator to have access control by enter MAC address of client stations. When Enable this function, could store up to 40 different MAC addresses. Please follow the format that it required when an address is input. * Click Apply to save your settings. User's Guide 16 - TRENDnet TEW-410APB | Manual - Page 18
Wireless Authentication Type: Auto: Auto is the default WEP option is implemented. Shared Key authentication supports authentication of clients as either a member set depending on the speed of your wireless network. You can select from a the AP and a wireless client. The default setting is AUTO. - TRENDnet TEW-410APB | Manual - Page 19
wireless default Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Access Point Clients hear the beacons and awaken to receive the broadcast and multicast messages. * Click Apply to save your settings. User's Guide - TRENDnet TEW-410APB | Manual - Page 20
support default, public. Then configure the community's access as either Read-Only or Read-Write. private You may change the SNMP Community's name from its default, public. Then configure the community's access as either Read-Only or Read-Write. Click Apply to save your settings. User's Guide - TRENDnet TEW-410APB | Manual - Page 21
you upgrade its firmware. To upgrade the AP's firmware: 1. Download the firmware upgrade file from the internet. 2. Extract the firmware upgrade file. 3. Click the Firmware Upgrade button. 4. On the Firmware Upgrade screen, click the Browse button to find the firmware upgrade file. User's Guide 20 - TRENDnet TEW-410APB | Manual - Page 22
5. Double-click the firmware upgrade file. 6. Click the Upgrade button, and follow the on-screen instructions. Note: Do not power off the AP or press the Reset button while the firmware is being upgraded. User's Guide 21 - TRENDnet TEW-410APB | Manual - Page 23
Problems I can't access my AP. Cause: The unit is not powered on. There is not a network connection. The computer you are using does not have a compatible IP Address. Resolution: Make sure your AP is powered on. Make sure that your computer has a compatible IP Address. Be sure that the IP Address - TRENDnet TEW-410APB | Manual - Page 24
devices that may cause interference. Check your IP Address to make sure that it is compatible with the Wireless AP. Technical Support You can find the most recent software and user documentation on the TRENDware website. TRENDware provides free technical support for all customers for the duration of
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
User’s Guide
0
TEW-410APB
Wireless 802.11g AP
User’s Manual
Version 1.4