Troy-Bilt CS 4265 Service Manual

Troy-Bilt CS 4265 Manual

Get Troy-Bilt CS 4265 PDF manuals and user guides View all Troy-Bilt CS 4265 manuals
Add to My Manuals
Save this manual to your list of manuals

Troy-Bilt CS 4265 manual content summary:

  • Troy-Bilt CS 4265 | Service Manual - Page 1
    Service Manual Chipper/Shredder - CS4210 and CS4265 NOTE: These materials are for use by trained technicians who are experienced in the service and repair of these instructions from time to power time. Therefore, it may be necessary to obtain the latest materials before servicing or repairing
  • Troy-Bilt CS 4265 | Service Manual - Page 2
  • Troy-Bilt CS 4265 | Service Manual - Page 3
    / Shredder Servicing MODEL CS4265 SHOWN Chipper / Shredder Servicing Troy-Bilt Models CS4210 and CS4265 1.3. Remove the two wing knobs on either side of the discharge chute and pivot the discharge chute upward. See Figure 1. 1. CLEANING THE REDUCTION CHAMBER WARNING: The impeller's shredder blade
  • Troy-Bilt CS 4265 | Service Manual - Page 4
    Chipper / Shredder Servicing 2.3. Pivot the shredder screen upward as instructed under the heading - Cleaning the Reduction Chamber. 2.4. Remove the chipper chute support brace from the frame by removing the two hex bolts and saddle washers which secure it. See Figure 2. 2.6. Rotate the impeller by
  • Troy-Bilt CS 4265 | Service Manual - Page 5
    Bracket Flange Nuts Chipper / Shredder Servicing 3.6. Insert a piece of wood into the discharge chute opening to stabilize the impeller and prevent it from rotating when removing the shredder blade. See Figure 7. Wood Stop Figure 5 3.3. Pivot the shredder screen upward as instructed under the
  • Troy-Bilt CS 4265 | Service Manual - Page 6
    Chipper / Shredder Servicing IMPORTANT: If sharpening the blade for reuse, follow the original angle of grind as a guide. Make certain each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. Remove metal from the heavy side until it is balanced evenly. See Figure 9.
  • Troy-Bilt CS 4265 | Service Manual - Page 7
    See Figure 12. Special Removal Tool 753-0638 Chipper / Shredder Servicing NOTE: In this chipper blades for any wear or damage. See Figure 13. Shredder Screen Impeller Assembly Flails (4) Figure 13 Figure 14 5. FLAIL REMOVAL AND REPLACEMENT. 5.1. Stop the engine and wait until all moving parts
  • Troy-Bilt CS 4265 | Service Manual - Page 8
    Chipper / Shredder Servicing 5.4. Remove the four hex cap screws securing the tube support to the frame assembly. See Figure 15. 5.6. The flails can be inspected and replaced by removing the roll pin retainer clip, roll pin and clevis pin. See Figure 17. Flail Roll Pin Retainer Clip Tube Support
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Service Manual
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
PRINTED IN USA
FORM NO.769-00944
This Service Manual is not a substitute for the Operator’s Manual. You must read, understand
and follow all of the directions in this manual as well as the Operator’s Manual before working
on this power equipment.
(10/2003)
Chipper/Shredder - CS4210 and CS4265
TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019