Viking FGNI Drain Pump - DPFGIM - Installation Instructions
Viking FGNI Manual
 |
View all Viking FGNI manuals
Add to My Manuals
Save this manual to your list of manuals |
Viking FGNI manual content summary:
- Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 1
a nugget / pearl ice machine. Cubed ice machine instructions begin now; nugget ice machine instructions are on page 6. Cubed Ice: Installation requires removal mode, perform a manual harvest. 2. Remove all ice. 3. Drain reservoir (remove reservoir drain cap). 4. Remove service panel and kick plate - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 2
9. Remove top panel. 10. Remove control box cover. 11. Disconnect thermistor from controller, pull wire back to suction line. Thermistor Connector 12. Remove curtain & hanger. 13. Locate elbows where water flows onto the evaporator platen. Clip Inlet Elbow Inlet Elbow Inner Elbow 14. Pull - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 3
16. Remove two screws holding freezing compartment brace to cabinet, lift brace up. 17. Lift evaporator platen up and tilt back enough for bin assembly to clear the base. Brace 18. Remove air baffle. Air Baffle 19. Unplug 7 wire harness connector (at back of bin). 20. Remove 1 screw at each - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 4
GRAVITY DRAIN CONVERSION INSTRUCTIONS 1. Uncoil the 10-foot long discharge tubing and push one end completely onto the barbed discharge elbow of the pump and securely fasten it with - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 5
• Pump motor to switch harness • Switch harness (black & white wires) to power cord connector half from step 7. • Switch harness (red & white wires) to machine connector half from step 7. 9. Refer to the unit's wiring diagram and re-check all electrical connections for proper placement. 10. Return - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 6
NUGGET / PEARL ICE MACHINE INSTRUCTIONS. Installation requires attachment of the switch mounting bracket to the base; power. Electrical Shock Hazard. Disconnect electrical power before beginning removal 5. Remove side service panel. Unit Shown With Side Service Panel Removed and Pump Installed 6 - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 7
6. Remove existing drain hose from unit. Drain Hose Electrical Harness Switch Bracket Pressure Switch Hose Assembled Drain Pump System 7. Uncoil the 10-foot long discharge tubing and push one end completely onto the barbed discharge elbow of the pump and securely fasten it with the small metal - Viking FGNI | Drain Pump - DPFGIM - Installation Instructions - Page 8
• Switch harness (black & white wires) to power cord connector half from step 13. • Switch harness (red & white wires) to machine connector half from step 13. 15. Refer to the unit's wiring diagram and re-check all electrical connections for proper placement. 16. Connect drain tube to bin drain, and
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
INSTALLATION
INSTRUCTIONS
INSTALLATION INSTRUCTIONS FOR DRAIN PUMP KITS A39462-021, KPU090 and DPFGIM
Kit contents:
•
Pump and motor with check valve
•
Switch mounting bracket assembled to switch assembly
•
Wire harness
•
Pressure hose (clear)
•
Drain hose (white preformed)
•
Stainless steel shield
•
Misc. hardware: Snap bushing, hose clamps, mounting bolts and screws
Note: This pump can be installed in a cubed ice machine or a nugget / pearl ice machine.
Cubed ice machine instructions begin now; nugget ice machine instructions are on page 6.
Cubed Ice: Installation requires removal of the cabinet from the base; attachment of the switch
mounting bracket to the base; attachment of the pump to the base; and connection of wire
harnesses and tubing. Stainless steel shield not used on cubers.
Removal of the cabinet:
1. If the machine is in a freeze mode, perform a manual harvest.
2. Remove all ice.
3. Drain reservoir (remove reservoir drain cap).
4. Remove service panel and kick plate.
5. Remove back panel.
6. Disconnect electrical power.
7. Disconnect water and drain tubing.
8. Remove door.
17-3265-01 Rev E
Electrical Shock
Hazard
.
Disconnect electrical
power before
beginning removal