Vtech vt20-2480 User Manual
Vtech vt20-2480 Manual
 |
View all Vtech vt20-2480 manuals
Add to My Manuals
Save this manual to your list of manuals |
Vtech vt20-2480 manual content summary:
- Vtech vt20-2480 | User Manual - Page 1
be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol - Vtech vt20-2480 | User Manual - Page 2
support under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust - Vtech vt20-2480 | User Manual - Page 3
packs, call VTech Communications Inc at 1-800-595-9511. In Canada, call VTech Electronics Ltd at 1-800-267-7377. OWNER'S MANUAL 4 The Handset Layout 1 2 3 9 4 10 5 11 6 7 12 8 13 14 15 1. Antenna 2. New Messages Indicator 3. Earpiece 4. Headset Jack (2.5mm) 5. Scroll Keys 6. Line - Vtech vt20-2480 | User Manual - Page 4
The Base Unit Layout 11 1 12 13 2 14 15 3 4 16 5 17 6 7 8 18 9 19 10 20 21 22 25 23 26 27 + ! 8L55 24 1. Itad On/Off 2. Record 3. Erase 4. Repeat 5. Spare Battery Indicator 6. Charging Contacts 7. Handset Charging Indicator 8. Mailboxes 9. Headset Key 10. Flash 11. LCD - Vtech vt20-2480 | User Manual - Page 5
Getting Started Getting Started Installation of Battery Pack in Handset Follow the steps below: 1. Remove the battery cover by pressing on the indent and sliding downward. 2. Place the new battery pack in the handset with the metal contacts aligned with the charge contacts in the battery - Vtech vt20-2480 | User Manual - Page 6
Getting Started Getting Started Dial Tone Checking for Dial Tone After the battery is charged press a LINE Key on the Handset. PHONE ON will appear on the handset display, and you will hear dial tone. If not, see In Case of Difficulty. Tone/Pulse Selection Your GIGAPHONE is set for TONE dialing. - Vtech vt20-2480 | User Manual - Page 7
Gettng Started Getting Started Registration and Operation Registration And Operation Of The VTech VT20-2420 Accessory Handset Your VTech GIGAPHONE system can operate up to 8 Handsets. The VTECH accessory Handset consists of the following: 1 3 5 Setup Of The VT20-2420 Accessory Handset 1. Plug the - Vtech vt20-2480 | User Manual - Page 8
Basic Operation Basic Operation Handset and Base Indicators Handset and Base Icons Icon Description Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For - Vtech vt20-2480 | User Manual - Page 9
phone book memory by scrolling until it is highlighted, then press SELECT, and then press SAVE. Then add a NAME to your entry by following the instructions under To Store a Number/Name. HANDSET MENU With the Handset in the idle (OFF) mode, press the MENU key to access the following options: • CALL - Vtech vt20-2480 | User Manual - Page 10
NEW NAME. Use the keypad to enter the name, then press SAVE. A guide to the letters and characters can be found in the section entitled Memory. 18 ID These are subscription services, provided by most regional telephone service providers. You must subscribe to these services to get the benefits - Vtech vt20-2480 | User Manual - Page 11
and operating range. Actual range will depend on your environment. You can manually turn Enhanced Mode ON and OFF, or select AUTO mode. To select , then press SET. Using the dialing keys, enter the desired name. A guide to the letters and characters can be found in the section entitled Memory. The - Vtech vt20-2480 | User Manual - Page 12
will be prompted to enter the 15-digit Base ID code. See Registration and Operation, located in the Getting Started section of the manual, for details. Note : Base ID codes are 15 digits long and can include the following characters: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, * , or # . Memory The Base and each - Vtech vt20-2480 | User Manual - Page 13
Basic Operation Basic Operation To Search For and Dial a Number/ Name: • Starting from the idle screen, press the MEM softkey to review memory contents. • Using the softkeys scroll through the memory contents in alphabetical order. • Or, you can press the FIND softkey, enter the first few - Vtech vt20-2480 | User Manual - Page 14
press the appropriate LINE key to dial the number ( follow the above instructions in Making Calls). You can also delete and save 'redial' numbers Conference both lines together. See Conference Calling, further on in this User's Manual. From the Base Unit If a line is ringing, pressing SPEAKERPHONE ( - Vtech vt20-2480 | User Manual - Page 15
lines together . See Conference Calling, further on in this User's Manual. Mute Function During an active call pressing either the MUTE soft key press SPEAKERPHONE.(or HEADSET) Flash Function You can use your GIGAPHONE with services such as call waiting. Simply press the LINE key on the Handset - Vtech vt20-2480 | User Manual - Page 16
AdvancedOperations AdvancedOperations Handset and Base Operation Highlight the desired destination of your intercom then press OK. Your screen will display CALLING HANDSET __, CALLING BASE, or PERFORMING GLOBAL PAGE. The recipient's screen will display INTERCOM FROM HANDSET 1, or GLOBAL CALL FROM - Vtech vt20-2480 | User Manual - Page 17
Handset and Base Operation Conference Calling The GIGAPHONE is capable of supporting conference calls with up to two registered Handsets on each line, and the Base unit. To enter a conference call, simply access the line with two - Vtech vt20-2480 | User Manual - Page 18
Answering System Operation ANSWERING SYSTEM SETUP (From either 20-2481 Handset or Base) HELPFUL HINT: Press CLEAR anytime to back out of setup mode. Depending on where you are in the setup process, you may have to press CLEAR more than once to return to the idle screen. • From the idle mode, press - Vtech vt20-2480 | User Manual - Page 19
the Mailbox to answer an incoming call after 2 rings if the Mailbox contains new, unplayed messages. If there aren't any unplayed messages, Toll Saver instructs the Mailbox to answer after 4 rings. Use Toll Saver if you're going out of town. When you access the Answering System remotely to check - Vtech vt20-2480 | User Manual - Page 20
Answering System Operation DAY AND TIME For accurate time and day stamps on your messages, set the current day and time. Setting either Mailbox will set the other, as well. From the Handset or Base Unit: • From the idle mode, press MENU. • Scroll to MAILBOXES, then press OK. • Scroll to either - Vtech vt20-2480 | User Manual - Page 21
AdvancedOperations AdvancedOperations Answering System Operation YOU CAN RECORD YOUR OUTGOING GREETINGS FROM EITHER THE VT20-2481 HANDSET OR BASE!! • From the idle mode, press MENU. • Scroll to MAILBOXES, then press OK. • Scroll to either MAILBOX SETUP line, then press OK. • Scroll to REVIEW/CHNG - Vtech vt20-2480 | User Manual - Page 22
AdvancedOperations AdvancedOperations Answering System Operation • From the idle mode, press MENU. • Scroll to MAILBOXES, then press OK. • Scroll to either MAILBOX line. Caution: Do not scroll down to MAILBOX 1 or 2 SETUP!! • Press OK. You will hear messages from the Handset Speakerphone. In - Vtech vt20-2480 | User Manual - Page 23
to use the Headset option, you must obtain an optional accessory Headset, which is compatible with the GIGAPHONE. To purchase a Headset, call VTECH Customer Service at 1-800-595-9511. Once you have a compatible 2.5mm Headset, locate the Headset Jack on the GIGAPHONE Handset. Connect the plug on the - Vtech vt20-2480 | User Manual - Page 24
the Base Unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your local telephone company. You Get Noise, Static, Or A Weak Signal Even When You're Near The Base Unit • Household appliances - Vtech vt20-2480 | User Manual - Page 25
or 4. Product to the extent that the problem is caused by use with non-VTECH electrical service? • To obtain warranty service in the United States of America, call 1 800-595- 9511 for instructions regarding where to return the Product. Before calling for service, please check the user's manual - Vtech vt20-2480 | User Manual - Page 26
hearing aids. Should you experience trouble with this telephone equipment, please contact: VTech Communications Inc. CUSTOMER SERVICE at 1-800-595-9511. In and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is - Vtech vt20-2480 | User Manual - Page 27
single line and an RJ14 jack for two lines. See Installation Instructions in the user's manual. This equipment may not be used with Coin Telephone Lines or service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem - Vtech vt20-2480 | User Manual - Page 28
Numeric Display 50 Memory locations SPECIFICATIONS ARE TYPICAL AND MAY CHANGE WITHOUT NOTICE. 54 Table Of Contents 1. Important Safety Instructions 3. Introduction 4. Parts Check List 5. The Handset Layout 6. The Base Unit Layout 7. Getting Started 7. Setup 8. Installation of Battery Pack in - Vtech vt20-2480 | User Manual - Page 29
VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications Inc.; Beaverton, Oregon. Distributed in Canada by VTech Electronics Canada Ltd., Suite 200, 7671 Alderbridge Way, Richmond, B.C. V6X 1Z9. Copyright 2002 for VTECH - Vtech vt20-2480 | User Manual - Page 30
- Vtech vt20-2480 | User Manual - Page 31
- Vtech vt20-2480 | User Manual - Page 32
- Vtech vt20-2480 | User Manual - Page 33
- Vtech vt20-2480 | User Manual - Page 34
setup, registration and basic functions. For detailed operational instructions, please refer to the VT20-2431 or VT20-2481 User's Manual. To order additional system Handsets (model# VT20 your phone to the store. Call our Customer Support Center at: 1-800-595-9511 In Canada, call 1-800-267-7377 1 - Vtech vt20-2480 | User Manual - Page 35
the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product electric shock. 12. Unplug this product from the wall outlet and refer servicing to VTECH under the following conditions: A. When the power supply cord or - Vtech vt20-2480 | User Manual - Page 36
Getting Started Setup Registration And Operation Of The VTECH VT20-2420 Accessory Handset Your VTECH 2-Line GIGAPHONE system can operate up to 8 Handsets. The VTECH accessory Handset consists of the following: L1 FLASH 1 OFF CLEAR 2 ABC L2 FLASH 3 DEF 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ - Vtech vt20-2480 | User Manual - Page 37
Enter Base ID Code 1. After charging the Handset, remove it from its Charge Cradle; the screen will display: alternating with this screen: Registration OK 2. If, after charging the Handset, you see: MENU 3. Press NEW. You will now see the ENTER BASE ID screen as described in step 1. 4. Find the - Vtech vt20-2480 | User Manual - Page 38
to use the Headset option, you must obtain an optional accessory Headset, which is compatible with the GIGAPHONE. To purchase a Headset, call VTECH Customer Service at 1-800-595-9511. Once you have a compatible 2.5mm Headset, locate the Headset Jack on the GIGAPHONE Handset. Connect the plug on the - Vtech vt20-2480 | User Manual - Page 39
the Base Unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Call your local telephone company. You Get Noise, Static, Or A Weak Signal Even When You're Near The Base Unit • Household appliances - Vtech vt20-2480 | User Manual - Page 40
a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company. You Hear Noise In The when installed and used normally and in accordance with operation instructions. This limited warranty extends only to the Consumer for - Vtech vt20-2480 | User Manual - Page 41
outside the unit. How do you get warranty service? • To obtain warranty service in the United States of America. call 1 800-595-9511 for instructions regarding where to return the Product. Before calling for service, please check the user's manual, A check of the Product controls and features may - Vtech vt20-2480 | User Manual - Page 42
trouble with this telephone equipment, please contact: VTech Communications Inc CUSTOMER SERVICE for two lines. See Installation Instructions in the user's manual. This equipment may not be instructions If the equipment is malfunctioning, it must be unplugged from the modular jack until the problem - Vtech vt20-2480 | User Manual - Page 43
the directory card, so that you can still dial the emergency number manually if the memory dialing feature doesn't work. b. This feature is provided hours, such as in the early morning or late evening, when the emengency services tend to be less busy. IC (Industry Canada) This telephone is registered - Vtech vt20-2480 | User Manual - Page 44
Technical Specifications FREQUENCY CONTROL Crystal controlled PLL synthesizer TRANSMIT FREQUENCY 2401.056 - 2481.408 MHz RECEIVE FREQUENCY 2401.056 - 2481.408 MHz CHANNELS 94 Channels WEIGHT Handset : Charger : 116 grams (excluding battery pack) 200 grams POWER REQUIREMENTS Handset : 2.4V - Vtech vt20-2480 | User Manual - Page 45
- Vtech vt20-2480 | User Manual - Page 46
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
 |
 |
1
0
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1.
Read and understand all instructions.
2.
Follow all warnings and instructions marked on the product.
3.
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
4.
Do not use this product near water (for example, near a bath tub, kitchen
sink, or swimming pool).
5.
Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
6.
Slots and openings in the cabinet and the back or bottom are provided
for ventilation. To protect it from overheating, these openings must not
be blocked by placing the product on the bed, sofa, rug, or other similar
surface. This product should never be placed near or over a radiator or
heat register.
This product should not be placed in a built-in installation
where proper ventilation is not provided.
7.
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8.
Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be abused by persons walking on it.
9.
Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts that could
result in a risk of fire or electric shock. Never spill liquid of any kind on
the product.
10.
To reduce the risk of electric shock, do not disassemble this product.
Opening or removing cabinet parts other than specified access doors may
expose you to dangerous voltages or other risks. Incorrect reassemb-ling
can cause electric shock when the appliance is subsequently used.
11.
Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
Important Safety Instructions