Westinghouse LD3235 User Guide
Westinghouse LD3235 Manual
 |
View all Westinghouse LD3235 manuals
Add to My Manuals
Save this manual to your list of manuals |
Westinghouse LD3235 manual content summary:
- Westinghouse LD3235 | User Guide - Page 1
2 NOTICES 3 FCC COMPLIANCE STATEMENT 4 IMPORTANT SAFETY INSTRUCTIONS 5 Circuit Overload 6 Power Cord Protection 6 Ventilation 6 WARNINGS AND PRECAUTIONS 7 ANTENNA INSTALLATION SAFETY 8 Lightning 8 Power lines 8 CLEANING THE LED TV 9 Dolby-Digital Notice 9 SRS Trademark Information - Westinghouse LD3235 | User Guide - Page 2
USER'S MANUAL MANUEL DE L'UTILISATEUR MANUAL DEL USUARIO LD-3235 - Westinghouse LD3235 | User Guide - Page 3
- Westinghouse LD3235 | User Guide - Page 4
- Westinghouse LD3235 | User Guide - Page 5
This device contains a digital television tuner, so it should receive digital over the air TV programming, with a suitable antenna, after the end of full-power analog TV broadcasting in the United States on June 12, 2009. The nationwide switch to digital television broadcasting will be complete - Westinghouse LD3235 | User Guide - Page 6
user-serviceable parts inside. Refer all servicing requirements to qualified service personnel. • The plug should be connected to a mains socket outlet in accordance with the installation instructions. CAUTION: The power supply outlet should be located near the LED TV and should be easily accessible - Westinghouse LD3235 | User Guide - Page 7
cord sets may be used. The cord set must be selected according to the current rating for the LED TV. Consult the table below for the selection criteria of power cords used in the United States and Canada. Cord Type SJT SVT Size of Conductor in Cord 18 AWG 16 AWG 14 AWG - Westinghouse LD3235 | User Guide - Page 8
device, pursuant to part 15 of the with the instructions. However, there LED TV and the receiver. • Connect the LED TV to an outlet on a circuit separate from to which the receiver is connected. • If the interference persists even after performing the above measures, consult the Westinghouse Service - Westinghouse LD3235 | User Guide - Page 9
instructions marked on the LED TV. Observe the following safety instructions. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions periods of time. • Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been - Westinghouse LD3235 | User Guide - Page 10
Periodically inspect the cords for damage. Install the LED TV near a wall socket outlet where the power . To ensure reliable operation of the LED TV and to protect it from overheating, placing the LED TV on a bed, sofa, rug or other similar surface. Do not place the LED TV in a built - Westinghouse LD3235 | User Guide - Page 11
to splash on it (e.g. flower vase). • Do not place heavy objects on the LED TV, audio/video cables, or power cord. • If the LED TV emits smoke, abnormal noise, or a strange odor, immediately turn it off and contact the Westinghouse Service Center by: - Logging on to www.wde.com. - Contacting the - Westinghouse LD3235 | User Guide - Page 12
Antenna discharge unit (NEC Section 810-20) Electric service equipment NEC: National Electrical Code Grounding Conductors (NEC Section 810-21) Grounding clamps Power service grounding electrode system (NEC Art 250 part H) Lightning Z Z Z For added protection for the LED TV during a lightning - Westinghouse LD3235 | User Guide - Page 13
English IMPORTANT INFORMATION CLEANING THE LED TV • Make sure the LED TV is turned off and the power cord is disconnected from the power outlet. • Never spray or pour any liquid directly onto the screen or the - Westinghouse LD3235 | User Guide - Page 14
source software used in this product and licensed under the GPL, LGPL, or other open source license is distributed WITHOUT ANY WARRANTY and WITHOUT ANY SUPPORT by Westinghouse Digital. - Westinghouse LD3235 | User Guide - Page 15
- Westinghouse LD3235 | User Guide - Page 16
CONTROL PANEL CONTROL PANEL MENU 1 2 VOL CH 3 INPUT 4 5 USB R L R L AV 2 Item 1. MENU 2. Volume +/- 3. Channel +/- 4. INPUT 5. Power Description Displays the LED TV setup screen. • Adjusts the volume during playback. • Selects an item on a menu screen. • Switches the channel during - Westinghouse LD3235 | User Guide - Page 17
external AV device such as a VCR, DVD player, set-top box, or game system. Connect to an audio output device. For service only. Connects the LED TV to an antenna or cable service. Connect to an external AV device such as a VCR, DVD player, set-top box, or game system. Connect to an external - Westinghouse LD3235 | User Guide - Page 18
again to toggle the sound back on. Toggles the TV power on or off. Adjusts the LED screen backlight. Toggles the Multichannel Television Sound options. Toggles TV or HDTV as the input source. Selects HDMI1 as the input source. Selects the Composite AV device as the input source. Not supported. - Westinghouse LD3235 | User Guide - Page 19
CONTROL TRANSMISSION RANGE Transmission range depends upon the reception angle. The range of coverage is 20° horizontal/vertical at a distance of 10 feet from the LED TV. 14 C.C. ZZZ MTS Favorite A B - Westinghouse LD3235 | User Guide - Page 20
LED TV BASE LED TV BASE CAUTION: The LED TV unit may be too heavy for one person to lift. If this is the case, make sure to ask for assistance in handling the LED TV to prevent physical injury and/or damage to the unit. INSTALLING THE LED TV BASE 1 Open the LED TV carton box. 2 Remove the LED TV - Westinghouse LD3235 | User Guide - Page 21
LED TV BASE REMOVING THE LED TV BASE If you intend to repack the LED TV unit (for shipping or storage) or you want to change the installation to a wall mount option, you must first remove the LED TV base. 1 Turn off the LED TV and all connected devices. 2 Disconnect the power cord from the LED TV - Westinghouse LD3235 | User Guide - Page 22
the LED TV (e.g. breaking of internal circuit). CABLE TV (CTV/DTV) CONNECTION The unit has a TV tuner TV to channel 3 or 4. Typically one of these channels is used. If a channel is unknown, consult your cable TV company.) For more specific instructions on installing cable TV, consult your cable TV - Westinghouse LD3235 | User Guide - Page 23
external device connections, see the operation manual of the external device you wish to connect to the LED TV. • Make sure that the correct cables are connected to each terminal. Improper cable connections may cause damage to the LED TV. You can enjoy picture and sound by connecting various audio - Westinghouse LD3235 | User Guide - Page 24
connections. Antenna / PC Audio amplifier Cable system AUDIO OUT RGB cable 3.5 mm stereo mini jack cable Audio cable Audio cable Antenna cable / Cable TV line R - L - AV S-VIDEO ANT. USB DC IN HDMI 1 HDMI 2 VGA AUDIO IN R - L AUDIO Y - Pb - Pr OUT AC adapter HDMI-HDMI cable DVI-HDMI - Westinghouse LD3235 | User Guide - Page 25
INITIAL SETUP Press on the control panel or on the remote control to turn on the LED TV. Select the desired language and select Yes to use the SetupWizard. The SetupWizard will guide you on how to set up the LED TV's operational settings. MENU VOL CH INPUT 20 C.C. ZZZ MTS Favorite A B - Westinghouse LD3235 | User Guide - Page 26
WESTINGHOUSE return to the previous screen. Setup Wizard The Setup Wizard will help guide you through scanning channels or accessing your connected set-top-box. Press the ATSC tuner and scan over-the-air ATSC channels. This LED HDTV is not capable of converting an ATSC signal until activated by the - Westinghouse LD3235 | User Guide - Page 27
Toll Free Phone Number, Website, or Text Message. Provide the activation service the Serial Number shown on your screen. Press Next to continue scan is complete you will be able to watch your local TV programming. WESTINGHOUSE HDTV SETUP - THROUGH CABLE/ SATELLITE BOX Select Language Use the - Westinghouse LD3235 | User Guide - Page 28
return to the previous screen. Setup Wizard The Setup Wizard will help guide you through scanning channels or accessing your connected set-top-box. Press activate the ATSC tuner and scan cable/satellite ATSC channels. This LED HDTV is not capable of converting an ATSC signal until activated by the - Westinghouse LD3235 | User Guide - Page 29
on your screen. Options will be from one to all of the following methods: Toll Free Phone Number, Website, or Text Message. Provide the activation service the Serial Number shown on your screen. Press Next to continue activation. Press Go Back to return to the previous screen. - Westinghouse LD3235 | User Guide - Page 30
keypad enter the activation code provided by the ATSC Tuner Activation service. Press Go Back to return to the previous screen. Channel When the scan is complete you will be able to watch your local TV programming. WESTINGHOUSE HDTV SETUP - NOT THROUGH CABLE/ SATELLITE BOX Select Language Use the up - Westinghouse LD3235 | User Guide - Page 31
Setup Wizard The Setup Wizard will help guide you through scanning channels or accessing your connected on your remote control to activate the ATSC tuner and scan cable/satellite ATSC channels. This LED HDTV is not capable of converting an ATSC signal until activated by the owner. Press Go - Westinghouse LD3235 | User Guide - Page 32
one to all of the following methods: Toll Free Phone Number, Website, or Text Message. Provide the activation service the Serial Number shown on your screen. Press Next to continue activation. Press Go Back to return to the the scan is complete you will be able to watch your local TV programming. 27 - Westinghouse LD3235 | User Guide - Page 33
off the power Press on the control panel or on the remote control to turn off the LED TV. The LED behavior will depend on the enabled Power settings. MENU VOL LED indicator Operation Turns from none to red. Turn the power on. Turns from red to none. Turn the power off. CH INPUT - Westinghouse LD3235 | User Guide - Page 34
BASIC OPERATIONS English CHANGING CHANNELS Follow the instructions below to change channels. Using the Ch / Buttons Input Vol Ch YPbPr1 HDMI1 Video1 TV Browse channels To browse through the available channels, press Ch / on the remote control or on the control panel. Using the Channel - Westinghouse LD3235 | User Guide - Page 35
Input Vol Ch YPbPr1 HDMI1 Video1 TV Select source using Input Key 1 Press Input. 2 A list of supported video sources is displayed. 3 Press Picture is scaled down to fit the display area. • 1:1 Mode: Matches the incoming resolution exactly to the pixels without any scaling. ADJUSTING THE LED - Westinghouse LD3235 | User Guide - Page 36
English SETUP MENUS SETUP MENUS SETUP MENU OPERATION Use the setup menus to configure the various operational settings of the LED TV. Displaying the setup menu screen Press on the remote control or MENU on the control panel to display the setup menu screen. Navigating the setup - Westinghouse LD3235 | User Guide - Page 37
control or MENU on the control panel to display the setup menu screen then select Picture to display the Picture sub-menu. The following options are available: Brightness, Contrast, Saturation, Video Presets, remote control to adjust the contrast level. 3 Press to save and exit the screen. 32 - Westinghouse LD3235 | User Guide - Page 38
Video Presets Showroom Movie Game Sports Custom The following options are available: • Showroom: Uses increased color and sharpness for a vibrant picture display. • Movie: Images are displayed as accurately near to its original recording condition. • Game: Uses increased brightness and response - Westinghouse LD3235 | User Guide - Page 39
. Color Temperature Use Color Temperature to adjust the level of white balance in the display. Color Temperature Warm Neutral Cool Three settings are available: • Warm: Pictures appear more reddish. • Neutral: Pictures appear more white. • Cool: Pictures appear with a bluish tint. 34 - Westinghouse LD3235 | User Guide - Page 40
save and exit the screen. Reset Select Yes on this sub-menu to reset all display-related settings. Reset NOTE: The configuration settings for the Picture sub-menus will only be applied to the current input source. 35 - Westinghouse LD3235 | User Guide - Page 41
SETUP MENUS English AUDIO Use the Audio sub-menus to configure the audio quality. These settings apply to the LED TV speakers only. Any connected audio devices are not affected. Press on the remote control or MENU on the control panel to display the setup menu - Westinghouse LD3235 | User Guide - Page 42
English SETUP MENUS Balance Use Balance to adjust the sound balance between the L/R speakers. SRS Balance Adjusting Balance 1 Use the / keys to select Balance and press . 2 Press the / keys on the remote control to adjust the balance level. 3 Press to save and exit the screen. DRC Use this sub- - Westinghouse LD3235 | User Guide - Page 43
English SETUP MENUS Audio Presets Use this sub-menu to select one of four preset audio options optimized for different sounding conditions. SRS Audio Presets Rock POP Classical Flat Custom The following options are available: • Rock: Sets the equalizer to the Rock mode. • POP: Sets the equalizer to - Westinghouse LD3235 | User Guide - Page 44
English SETUP MENUS Adjusting TruSurround HD 1 Use the / keys to select TruSurround HD and press . 2 Press the / keys on the remote control to select ON or OFF. 3 Press to save and exit the screen. Reset Select Yes on this sub-menu to reset all audio-related settings. SRS Reset 39 - Westinghouse LD3235 | User Guide - Page 45
, Fill, Overscan, and 1:1 Mode. English View Mode 1:1 Mode Standard Fill Overscan Standard Picture is displayed in its original size. Fill Picture is displayed to cover the entire screen. Overscan Picture is scaled down to fit the display area. 1:1 Mode Matches the incoming resolution - Westinghouse LD3235 | User Guide - Page 46
in the following options: • 1:1 Mode: Matches the incoming resolution exactly to the pixels without any scaling. • Standard: Picture is displayed in its original size. • Fill: Picture is displayed to cover the entire screen. English H. Position Use this sub-menu to adjust the horizontal position - Westinghouse LD3235 | User Guide - Page 47
control or MENU on the control panel to display the setup menu screen then select TV Program to display the TV Program sub-menu. The following options are available: Skip List, Channel Edit, MTS, Auto Search, and Manual Add. Skip List Use Skip List to select the channels you want to skip. Channel - Westinghouse LD3235 | User Guide - Page 48
English SETUP MENUS Channel Edit Use Channel Edit to assign a name to a channel. Channel Name Edit 11.0 13.0 16.1 17.0 21.0 22.0 23.0 24.0 :Select Enter: Confirm Menu: Exit Editing Channel Names 1 Use the / keys to select Channel Edit and press Name Edit screen appears. . The Channel 2 Use - Westinghouse LD3235 | User Guide - Page 49
following options are available: • Mono: Allows mono output (useful when stereo is noisy or inconsistent). • Stereo: Allows stereo sound for superior TV viewing experience. • SAP: Allows second audio program from the speakers while watching a scene in the original program. Adjusting MTS 1 Use the - Westinghouse LD3235 | User Guide - Page 50
:Select Enter: Confirm Menu: Exit Adding Channels Manually 1 Use the / keys to select Manual Add and press screen appears. . The Channel Add 2 Use the Channel keys on the remote control to enter the channel number and select Enter. Wait a few moment for the TV to search for the channel. 3 When - Westinghouse LD3235 | User Guide - Page 51
SETUP MENUS English SETTINGS Use the Settings sub-menus to configure the LED TV operational setup and view the current firmware version. Press on the remote control or MENU on the control panel to display the setup menu screen - Westinghouse LD3235 | User Guide - Page 52
) Adjust for Daylight Saving Time. 3 Press to save and exit the screen. Closed Captions Use Closed Captions to configure the settings for closed captioning in TV programs. The following options are available: • Closed Captions: Can be set to ON or OFF. • Analog Type: Can be set to CC1,CC2, CC3, CC4 - Westinghouse LD3235 | User Guide - Page 53
English SETUP MENUS • Font: Can be set to As Broadcaster, Style 1, Style 2, Style 3, Style 4, Style 5, Style 6, or Style 7. • Size: Can be set to As Broadcaster, Small, Medium, or Large. • Font Color: Can be set to As Broadcaster, Black, White, Green, Blue, Red, Cyan, Yellow, or Magenta. • - Westinghouse LD3235 | User Guide - Page 54
to select ON or OFF. 3 Press to save and exit the screen. • TV Rating: Use this sub-menu to customize US TV Rating programs. TV-PG TV-PG All D L S V :Select Enter: Confirm Menu: Exit Rating TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA FV D L S V Description Suitable for young children. May not be suitable - Westinghouse LD3235 | User Guide - Page 55
1 Use the / keys to select TV Rating and press . 2 Use the / / / keys to select the desired rating and press repeatedly to block or unblock. You can also select Lock All to - Westinghouse LD3235 | User Guide - Page 56
to save and exit the screen. • Canada English: Use this sub-menu to select the classification categories (based on Canadian ratings) of allowable TV programs and movies. English Rating E C C8+ G PG 14+ 18+ Description Exempt shows Suitable for viewing by children of all ages. Not suitable for - Westinghouse LD3235 | User Guide - Page 57
press repeatedly to block or unblock. 3 Press to save and exit the screen. • Canada French: Use this sub-menu to select the ratings of allowable TV programs and movies. These ratings are based on the classification categories determined by La Régie du cinéma du Québec. English Rating E G 8 ans - Westinghouse LD3235 | User Guide - Page 58
English SETUP MENUS • Channel Block: Channel Block allows you to block channels. 11.0 13.0 16.1 17.0 21.0 22.0 23.0 Adjusting Channel Block 1 Use the / keys to select Channel Block and press . 2 Use the / keys to select the desired channel and press repeatedly to block or unblock. 3 Press to save - Westinghouse LD3235 | User Guide - Page 59
English SETUP MENUS OSD Timeout Use OSD Timeout to adjust the OSD duration on the screen: 10 sec, 20 sec, or 30 sec. en OSD Timeout 10 sec 20 sec 30 sec Adjusting OSD Timeout 1 Use the / keys to select OSD Timeout and press . 2 Press the / keys on the remote control to select 10 sec, 20 sec, or - Westinghouse LD3235 | User Guide - Page 60
this sub-menu to configure power-related settings for the LED TV. Power Settings Backlight: Dynamic Contrast: Bright Room OFF and exit the screen. Reset All Select Yes on this sub-menu to reset all LED TV operational settings. Do this only if any of the following conditions occurs: • The system - Westinghouse LD3235 | User Guide - Page 61
English SETUP MENUS Version Use this sub-menu to view the LED TV's serial number and firmware version. en Version 56 - Westinghouse LD3235 | User Guide - Page 62
mm screws to wall mount the LED TV. WALL MOUNT INSTALLATION REMINDERS • Remove the LED TV base first before mounting the unit on a wall. • It is the user's responsibility to use a UL listed wall mount unit rated to support the weight of this LED TV. • Please consult qualified contractors for wall - Westinghouse LD3235 | User Guide - Page 63
TROUBLESHOOTING TROUBLESHOOTING English Problem No power Power is suddenly turned off. Forgotten PIN Remote control does not work. Remote control code cannot be detected by a universal remote. No picture Corrective Action • Make sure the power indicator is illuminated blue. • Make sure the power - Westinghouse LD3235 | User Guide - Page 64
English TROUBLESHOOTING Problem Corrective Action No picture or the No • Signal message appears when a • VGA cable is connected. • Make sure the VGA cable is properly connected to the LED TV's VGA port. Decrease the video resolution setting on the computer and try again. Adjust the - Westinghouse LD3235 | User Guide - Page 65
English TROUBLESHOOTING Problem Corrective Action • Make TV Speakers option is set to Off in Audio menu. NOTES: If the problem condition persists even after performing the recommended corrective actions, contact us by: • Logging on to www.wde.com • Contacting the Westinghouse Customer Service - Westinghouse LD3235 | User Guide - Page 66
www.westinghousedigital.com S/N: Westinghouse Digital, LLC Orange, CA SE-UM-3207-0101
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
 |
 |
TABLE OF CONTENTS
i
English
TABLE OF CONTENTS
TABLE OF CONTENTS
....................................................
i
DIGITAL TELEVISION TRANSITION NOTICE
..................
1
IMPORTANT INFORMATION
..........................................
2
Warnings
....................................................................
2
NOTICES
...................................................................
3
FCC COMPLIANCE STATEMENT
...............................
4
IMPORTANT SAFETY INSTRUCTIONS
.......................
5
Circuit Overload
.........................................................
6
Power Cord Protection
................................................
6
Ventilation
..................................................................
6
WARNINGS AND PRECAUTIONS
...............................
7
ANTENNA INSTALLATION SAFETY
............................
8
Lightning
....................................................................
8
Power lines
................................................................
8
CLEANING THE LED TV
.............................................
9
Dolby-Digital Notice
....................................................
9
SRS Trademark Information:
.......................................
9
PACKAGE CONTENTS
.................................................
10
CONTROL PANEL
........................................................
11
TERMINALS
.................................................................
12
REMOTE CONTROL
.....................................................
13
REMOTE CONTROL OPERATION
................................
14
INSTALLING THE REMOTE CONTROL BATTERIES.. 14
REMOTE CONTROL TRANSMISSION RANGE
..........
14
LED TV BASE
..............................................................
15
INSTALLING THE LED TV BASE
..............................
15
REMOVING THE LED TV BASE
................................
16
ANTENNA CONNECTION
.............................................
17
OUTDOOR ANTENNA CONNECTION
.......................
17
CABLE TV (CTV/DTV) CONNECTION
.......................
17
EXTERNAL DEVICE CONNECTIONS
............................
18
POWER CONNECTION
................................................
20