Whirlpool WED49STBW Dimension Guide
Whirlpool WED49STBW Manual
![]() |
View all Whirlpool WED49STBW manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WED49STBW manual content summary:
- Whirlpool WED49STBW | Dimension Guide - Page 1
PRODUCT MODEL NUMBERS WED49STB Front View 29" (737 mm) Electric Dryer Side View 223/4" (578 mm) 273/4" (705 mm) 133/4" (349 allowed. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for wall, door, and floor moldings - Whirlpool WED49STBW | Dimension Guide - Page 2
Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified ° turns as possible. Vent System Chart (Long Vent Models Only) Number of 90° turns or elbows 0 dryer. ■■ Reduce performance, resulting in longer drying times and increased energy usage. Because Whirlpool
![](/manual_guide/products/whirlpool-wed49stbw-dimension-guide-ea236dd/1.png)
Electric Dryer
PRODUCT MODEL NUMBERS
W10646601A
12/2014
WED49STB
29"
(737 mm)
43
3
/
8
"
(1102 mm)
1
/
2
"
(13 mm)
NOTE:
Leveling legs should be 1/2" (13 mm) (to match
height of 3.6 cu. ft. capacity washer) or 1½" (38 mm) (to
match height of 3.8 cu. ft. capacity washer). The location
must be large enough to allow the dryer door to open fully.
Front View
A
B
22
3
/
4
"
(578 mm)
27
3
/
4
"
(705 mm)
27
3
/
4
"
(705 mm)
13
3
/
4
"
(349 mm)
Side View
A. Wide opening side-swing door
B. Wide opening hamper door
*Most installations require a minimum 5½" (140 mm) clearance
behind the dryer for the exhaust vent with elbow. See “Venting
Requirements.”
Back View
30
1
/
4
"
(768 mm)
14
1
/
2
"
(368 mm)
4
3
/
4
"
(121 mm)
4"
(101 mm)
14
1
/
2
"
(368 mm)
4
3
/
4
"
(121 mm)
Steam
Non-Steam
Minimum spacing for recessed area or closet installation
The dimensions shown following are for the minimum spacing allowed.
■
Additional spacing should be considered for ease of installation
and servicing.
■
Additional clearances might be required for wall, door, and floor
moldings.
■
Additional spacing of 1" (25 mm) on all sides of the dryer
is recommended to reduce noise transfer.
■
For closet installation, with a door, minimum ventilation openings in
the top and bottom of the door are required. Louvered doors with
equivalent ventilation openings are acceptable.
■
Companion appliance spacing should also be considered.
Minimum Required Spacing
3"*
(76 mm)
3"*
(76 mm)
24 in.
2
*
(155 cm
2
)
48 in.
2
*
(310 cm
2
)
18"*
(457 mm)
1"*
(25 mm)
1"*
(25 mm)
5
1
/
2
"*
(140 mm)
14"* max.
(356 mm)
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
*Required spacing