Whirlpool WED8300S Use and Care Guide
Whirlpool WED8300S Manual
 |
View all Whirlpool WED8300S manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WED8300S manual content summary:
- Whirlpool WED8300S | Use and Care Guide - Page 1
® ® ELECTRONIC ELECTRIC DRYER Use & Care Guide For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301 or visit our website at... www.whirlpool.com Table of Contents 2 W10151580A - Whirlpool WED8300S | Use and Care Guide - Page 2
CONTENTS DRYER SAFETY 2 INSTALLATION INSTRUCTIONS 3 Tools and Parts 3 Optional Pedestal 4 Location Requirements 4 Electrical Requirements 6 Electrical Connection 8 Venting Requirements 13 Plan Vent System 14 Install Vent System 15 Install Leveling Legs 15 Connect Vent 15 Level Dryer 15 - Whirlpool WED8300S | Use and Care Guide - Page 3
Do not install or store the dryer where it will be exposed to the weather. ■ Do not tamper with controls. ■ Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand - Whirlpool WED8300S | Use and Care Guide - Page 4
a drying rack, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section. Ask for Part Number 8563738. For more information, see "Drying Rack Option." Stack Kit Are you planning to stack your DUET SPORT™ washer and dryer? To do so, you will need to purchase - Whirlpool WED8300S | Use and Care Guide - Page 5
spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons: ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional - Whirlpool WED8300S | Use and Care Guide - Page 6
spacing is allowed. Recommended installation spacing for recessed or closet installation, with stacked washer and dryer The dimensions shown are for the volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30 - Whirlpool WED8300S | Use and Care Guide - Page 7
follow the instructions provided for it here. ■ If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" in the "Electrical Connection" section. ■ This dryer is manufactured ready to install with a 3-wire electrical supply connection - Whirlpool WED8300S | Use and Care Guide - Page 8
death, fire, or electrical shock. 1. Disconnect power. 2. Remove the hold-down screw and terminal block cover. C D B A A. Neutral ground wire B. External ground conductor screw C. Center, silver-colored terminal block screw D. Terminal block cover and hold-down screw 3. Install strain relief. Style - Whirlpool WED8300S | Use and Care Guide - Page 9
10-30R) A UL listed, 120/ 240-volt minimum, 30-amp, dryer power supply cord* 3-wire connection: Power supply cord 3-wire direct 3¹⁄₂" of 3-wire connections. B F A 4. Now complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire - Whirlpool WED8300S | Use and Care Guide - Page 10
Tighten screws. 5. Tighten strain relief screws. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 10 D E A. External ground conductor screw - Dotted line shows - Whirlpool WED8300S | Use and Care Guide - Page 11
. Tighten screws. 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Power supply cord Use where local codes - Whirlpool WED8300S | Use and Care Guide - Page 12
screws. 4. Tighten strain relief screw. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. Now go to "Venting Requirements." 4. Tighten strain relief screws. 5. Connect a separate copper ground - Whirlpool WED8300S | Use and Care Guide - Page 13
performance. ■ Do not install flexible metal vent in flexible heavy metal vent. ■ Review Vent system chart. Modify existing Whirlpool Parts and Accessories. For more information, see the "Assistance or Service metal vent must be fully extended and supported when the dryer is in its final location. A - Whirlpool WED8300S | Use and Care Guide - Page 14
Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions. B C D A E F G A. Dryer B. Elbow C. Wall D. Exhaust hood H E. Clamps F. Rigid metal or flexible metal vent G. Vent - Whirlpool WED8300S | Use and Care Guide - Page 15
chart provides venting requirements that will help to achieve the best drying performance. Vent system chart NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart. Number of 90º turns or elbows Type of vent - Whirlpool WED8300S | Use and Care Guide - Page 16
You can change your door swing from a right-side opening to a left-side opening, if desired. 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. Remove the door assembly Reverse hinge 1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner - Whirlpool WED8300S | Use and Care Guide - Page 17
side. B A A. Plug strip (cannot be seen from this angle) B. Door strike Reinstall the door 1. Reattach door to dryer front panel with the 4 screws. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped - Whirlpool WED8300S | Use and Care Guide - Page 18
fire. WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Follow these basic steps to start your dryer. Please refer to specific sections of this manual for more detailed information. 1. Clean lint screen - Whirlpool WED8300S | Use and Care Guide - Page 19
desired, add a fabric softener sheet. Follow package instructions. ■ Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. settings. ■ Refer to the Auto or Manual Preset Cycle Settings chart (in the "Cycles" section) for a guide to drying various loads. ■ Drying temperature - Whirlpool WED8300S | Use and Care Guide - Page 20
heat for drying no-iron fabrics such as sport shirts, casual business clothes and permanent press Manual Cycles Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual left in the dryer too long. Manual Preset Cycle Settings Manual Cycles Load Type - Whirlpool WED8300S | Use and Care Guide - Page 21
whether your model allows drying rack usage and for more information on ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer. NOTE: The rack must be removed for normal tumbling. Do not use the automatic cycle with the drying rack. 21 - Whirlpool WED8300S | Use and Care Guide - Page 22
Wet lint is hard to remove. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. 2. Push the lint screen firmly back into - Whirlpool WED8300S | Use and Care Guide - Page 23
: 1. Unplug the power supply cord. 2. Make sure leveling legs are secure in dryer base. 3. Use masking tape to secure dryer door. For direct-wired dryers: WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in - Whirlpool WED8300S | Use and Care Guide - Page 24
TROUBLESHOOTING First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call... In U.S.A. www.whirlpool.com/help - In Canada www.whirlpool.ca Dryer Operation Dryer will not run ■ Has a household fuse blown, - Whirlpool WED8300S | Use and Care Guide - Page 25
openings at the top and bottom of the door. The front of the dryer requires a minimum of 1" (2.5 cm) of airspace, and, for most installations, the rear of the dryer requires 5" (12.7 cm). See "Installation Instructions." ■ Has the Air Only modifier been selected? Select the right temperature for the - Whirlpool WED8300S | Use and Care Guide - Page 26
number or your nearest designated service center. For assistance and service Call the Whirlpool Customer eXperience Center toll free: 1-800-253-1301. Our consultants provide assistance with: ■ Features and specifications on our full line of appliances ■ Installation information ■ Use and maintenance - Whirlpool WED8300S | Use and Care Guide - Page 27
Notes 27 - Whirlpool WED8300S | Use and Care Guide - Page 28
WHIRLPOOL WILL NOT PAY FOR 1. Service calls to correct the installation of your major appliance, to instruct YOU SPECIFIC Whirlpool dealer to determine if another warranty applies. If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
ELECTRONIC
ELECTRIC DRYER
Use & Care Guide
For questions about features, operation/performance, parts,
accessories or service, call:
1-800-253-1301
or visit our website at...
www.whirlpool.com
Table of Contents
....................................................
2
W10151580A
®
®