Whirlpool WED94HEXL Installation Instructions
Whirlpool WED94HEXL Manual
 |
UPC - 883049217253
View all Whirlpool WED94HEXL manuals
Add to My Manuals
Save this manual to your list of manuals |
Whirlpool WED94HEXL manual content summary:
- Whirlpool WED94HEXL | Installation Instructions - Page 1
ELECTRIC DRYER INSTALLATION INSTRUCTIONS Para una version de estas instrucciones en español, visite www.Whirlpool.com Table of Contents DRYER SAFETY 2 Installation Requirements 3 Tools and Parts 3 Location Requirements 4 Electrical Requirements 4 INSTALL LEVELING LEGS 6 ELECTRICAL INSTALLATION - Whirlpool WED94HEXL | Installation Instructions - Page 2
DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2 - Whirlpool WED94HEXL | Installation Instructions - Page 3
#2 Phillips screwdriver Wire stripper (direct wire installations) Tin snips (new vent installations) Parts needed: (Not supplied with dryer) ■■Vent clamps ■■Vent elbows and ductwork Additional parts may be required, depending in your installation. Check local codes. Check existing electrical - Whirlpool WED94HEXL | Installation Instructions - Page 4
entire dryer. If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number dryer not to shut off at end of automatic sensor cycles, resulting in longer drying times. Installation Clearances For each arrangement, consider allowing more space for ease of installation and servicing - Whirlpool WED94HEXL | Installation Instructions - Page 5
and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Mobile home installations require: ■■Metal exhaust system hardware, available for purchase from your dealer. For further information, see "Assistance or Service" section in your Use and Care Guide. ■■Special provisions must be made - Whirlpool WED94HEXL | Installation Instructions - Page 6
, at least 4 ft. (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R. Install Leveling Legs 1. Prepare dryer for leveling legs If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire) and be: ■■Flexible armored - Whirlpool WED94HEXL | Installation Instructions - Page 7
For power supply cord installations: For direct wire installations: Before you start: disconnect power. 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to Power Supply Cord Connection. Power - Whirlpool WED94HEXL | Installation Instructions - Page 8
. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. If your outlet looks like this: Power supply cord - Whirlpool WED94HEXL | Installation Instructions - Page 9
neutral wire B C Connect remaining wires under outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to Venting Requirements. Connect neutral wire (white or center) (C) of power supply - Whirlpool WED94HEXL | Installation Instructions - Page 10
. 1. Prepare your 4-wire cable for direct connection 31 (89 ⁄2" mm) (251"mm) (127 5" mm) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 - Whirlpool WED94HEXL | Installation Instructions - Page 11
block (B). Squeeze hooked ends together and tighten screw. 4. Connect ground wire (893m½m" ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 31/2" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable - Whirlpool WED94HEXL | Installation Instructions - Page 12
tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to terminal block screws. Tighten screws. A 4. Connect external ground wire Install the correct strain relief for your electrical connection method, as shown on - Whirlpool WED94HEXL | Installation Instructions - Page 13
supported in final dryer location. ■■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■■ Do not install plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent System Chart and if necessary, modify existing vent system to - Whirlpool WED94HEXL | Installation Instructions - Page 14
Plan Vent System Choose your exhaust installation type Recommended exhaust installation: B C A D F E G A. Dryer B Elbow C. Wall D. Exhaust hood E. Clamps B H F. Rigid metal or flexible metal vent G. Vent length necessary to connect elbows H. Exhaust outlet Special provisions for mobile - Whirlpool WED94HEXL | Installation Instructions - Page 15
exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. 2. Connect vent to exhaust hood Connect Inlet Hose The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old - Whirlpool WED94HEXL | Installation Instructions - Page 16
hose to "Y" connector and tighten couplings Remove protective cap from water inlet valve. Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector. Using pliers, tighten the couplings an additional two-thirds - Whirlpool WED94HEXL | Installation Instructions - Page 17
exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. 2. Move dryer to final location Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly. Not Level LEVEL Not Level - Whirlpool WED94HEXL | Installation Instructions - Page 18
on console and any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read "Dryer Use" in your Use and Care Guide. q For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on Power. q If you live in - Whirlpool WED94HEXL | Installation Instructions - Page 19
instructions are for models with a round-shaped door. IMPORTANT: For models with a square shaped door, an additional kit is needed. Please contact your retailer, or see the For Assistance or Service page in your Use and Care Guide dryer. Rotate the strike 180° and attach to the opposite side of dryer - Whirlpool WED94HEXL | Installation Instructions - Page 20
4. R emove outer window assembly from trim ring 5. Reverse outer window assembly Handle A A B Using a Phillips screwdriver, remove the 2 screws from the outer window retainer and rotate the outer window assembly clockwise until the square notches line up with the 4 tabs on the trim ring - Whirlpool WED94HEXL | Installation Instructions - Page 21
6. Rotate and reassemble outer window assembly to trim ring Bottom of door 7. Remove hinge and latch Latch Notches A Hinge Using a Torx® T25 screwdriver, remove the 3 Torx screws securing the latch plate and latch backing plate and the 5 screws holding the hinge assembly in place. 8. - Whirlpool WED94HEXL | Installation Instructions - Page 22
the door facing up. Reinstall the 10 screws securing the inner door to the outer door. 10. Reinstall door on dryer Using a Torx® T25 screwdriver, remove the 4 screws on the dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place - Whirlpool WED94HEXL | Installation Instructions - Page 23
23 - Whirlpool WED94HEXL | Installation Instructions - Page 24
W10057363B W10310420B - SP © 2010 All rights reserved 11/10 Printed in U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
W10057363B
W10310420B - SP
Table of Contents
DRYER SAFETY
.........................................................................
2
INSTALLATION REQUIREMENTS
.............................................
3
Tools and Parts
......................................................................
3
LOCATION REQUIREMENTS
....................................................
4
ELECTRICAL REQUIREMENTS
................................................
4
INSTALL LEVELING LEGS
.........................................................
6
ELECTRICAL INSTALLATION
...................................................
7
Power Supply Cord Connection
...........................................
8
Direct Wire Connection
.......................................................
10
VENTING
...................................................................................
13
Venting Requirements
.........................................................
13
Plan Vent System
.................................................................
14
Venting Kits
..........................................................................
14
Install Vent System
..............................................................
15
CONNECT INLET HOSE
..........................................................
16
CONNECT VENT
......................................................................
17
LEVEL DRYER
..........................................................................
17
COMPLETE INSTALLATION CHECKLIST
..............................
18
DOOR REVERSAL (OPTIONAL)
..............................................
19
ELECTRIC DRYER INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
Date of purchase:
_________________________________
Date of installation:
_______________________________
Installer:
________________________________________
Model number:
___________________________________
Serial number:
___________________________________
Para una version de estas instrucciones en español, visite www.Whirlpool.com