Yamaha M7CL M7cl V1 Editor Owner's Manual
Yamaha M7CL Manual
 |
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha M7CL manual content summary:
- Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 1
personal use. • Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. • The screen displays as illustrated in this owner's manual are for instructional purposes - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 2
of M7CL Editor M7CL Editor enables you to remotely control the Yamaha M7CL mixing console and to save the parameter settings on your computer. To use M7CL Editor, you must first perform the following operations: 1 Start and configure Studio Manager. 2 Start and configure M7CL Editor. 3 Synchronize M7CL - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 3
the Mixer Setup window, choose [Mixer Setup] from the [File] menu. 1 2 3 A Input Channels Specify the number of input channels on the M7CL console. When the editor is synchronized with the M7CL console, the actual number of channels on the M7CL console will automatically be specified here. B Mix Bus - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 4
required if no Administrator password has been specified on the M7CL console, but if this password is incorrect you will be asked to enter it when the user key is read. G ACCESS PERMISSION In this area, specify the parameters that this user will be allowed to operate. 4 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 5
. N SYSTEM SETUP MIXER SETUP: Change the privileges for making mixer setup settings. OUTPORT SETUP: Change the privileges for making outport setup settings. MIDI: Change the privileges for making MIDI settings. O Create Creates the user key. P Cancel Closes the window. 5 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 6
successfully undo or redo any previous operation: • Operations on the M7CL console • Quitting Studio Manager • Synchronizing with the M7CL console • Session operations NOTE You cannot Undo or Redo the following operations: • Edits in the Setup window • Synchronization • Opening and closing the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 7
each window from the [Windows] menu. For the INPUT CH window and Effect Editor window, use the sub-menu to select the channels or library you want to see. You can choose Tile or Cascade to arrange the windows within the editor. ● Tile ● Cascade In the Library window or Scene window, click the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 8
M7CL Editor to your console. Console ➔ PC: Transfers the current parameter settings of your console to the M7CL Editor. 3 Click [OK]. Do not operate the console while synchronization is in progress. NOTE If you use the "Total Recall" function in Studio Manager, all selected Editors in Studio Manager - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 9
also use the channel name text box to edit the name. This is linked with the [SEL] keys on the M7CL itself. You can right-click the icon to select a different one. ❏ SYNC This indicates the status of connection and synchronization between M7CL Editor and the M7CL. 12 A [ONLINE]/[OFFLINE] button - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 10
the MIX window. G [MTRX] button Opens the MATRIX window. H [33-48] button Opens the INPUT CH 33-48 window. This is available only during offline editing and when 48 is selected as the number of input channels in the Mixer Setup window, or when editing online with the M7CL-48. 10 M7CL Editor Owner - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 11
of the USER DEFINED KEYS to [1-16]/[17-32]/[33-48](*) in [INPUT CH] of [M7CL EDITOR CONTROL], and execute the function (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. A Input - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 12
a GR meter is shown MIX/MATRIX buses. • Post/off (yellow) To switch a send on/off, click the channel number located at the left of the bar graph. NOTE For FIXED-type MIX buses, the bar graph is fixed at nominal level (0 dB), and only the on/off status is shown. 12 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 13
number. If you hold down the key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. Q Channel name This is a text box that displays the channel name. You can also edit the channel name in this text box. 13 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 14
window you can view and edit the mix parameters of ST IN channels 1-4. The parameters shown in the window nal head amp (AD8HR) patched to the ST IN channel. 6 C 48V Switches on/off the phantom power (+48V) of the internal head amp or of the external INPUT CH (➥ p.12). 14 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 15
STEREO MONO for an INPUT channel (➥ p.13). J SEL (Select) 9 Selects the ST IN channel for which you want to perform operations. (L and R can be selected separately.) This is linked with the ST IN section [SEL] keys on the M7CL's J panel. K L K CUE This button cue-monitors the signal of the ST - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 16
MIX channel, from the 2 following choices. OMNI1-OMNI16 OMNI jacks 1-16 SLOT1-1, SLOT1-2...SLOT3-16 Input channels of an I/O card installed in slot 1-3 3 RACK1A, RACK1B...RACK8R(B) L/R outputs of Rack 1-8 4 2TROUT L, 2TROUT R L/R channels of the 2TR OUT DIGITAL M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 17
This parameter can be switched in Mix Bus Setup of the Mixer Setup screen. H SEL (Select) Selects the MIX channel for which you want to make settings. I CUE L This button cue-monitors the signal of the MIX channel. J ON M Switches the MIX channel on/off. K Fader Adjusts the output level of - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 18
this window you can view and edit the parameters of MATRIX channels 1-8. The parameters shown in the window can be selected from the [Windows] menu, choose [Overview] and then choose "MATRIX" ● Use the navigation keys in the Master window to turn on the [MTRX] button 18 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 19
method of operation and the meaning of the display are the same as for (5) MATRIX in the MIX window 2 (➥ p.17). (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. 3 B STEREO - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 20
. (The L/R settings are linked.) D MATRIX SEND Here you can view and edit the send levels of the signals sent from the STEREO/MONO channel to MATRIX 1-8 bus. The method of operation and the meaning of the display are the same as for MATRIX in the MIX window (➥ p.17). 20 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 21
This is the channel number (ST or M). You can double-click this number to open the Selected Channel window for this channel. If you hold down the key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. 21 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 22
, the R character at the lower right of the fader is dis- played in green. D DCA number 4 This is the number of the DCA group. 5 E DCA group name This is a text box that displays the DCA group name. You can also edit the DCA group name in this text box. 22 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 23
1-4), MIX channels, MATRIX channels, and STEREO/MONO channels. (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. If an input channel is selected ● INPUT CH window 23 M7CL Editor - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 24
in the INPUT section of the M7CL's panel. You can right-click the icon and select the desired choice. You can also edit the channel name in the text box. B INPUT PATCH Selects the input source assigned to the input channel (for the selectable input sources, ➥ p.11). 24 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 25
, and POST FADER when this is off. The PRE POINT setting can be specified in the Mixer Setup screen. C ON (MIX send on/off) This is an on/off switch for the signal sent from the input channel to the MIX bus and MATRIX bus. HINT • If MIX buses or MATRIX buses are being used in stereo - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 26
of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. CSR (Center Side Ratio) Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0-100%. 26 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 27
/off. C EQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the key either TYPE I (the algorithm used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. 27 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 28
es the amount by which the signal is attenuated while the gate is closed. H DECAY Specifies the time over which the gate will close after the hold time has elapsed. I ATTACK Specifies the time from when the key-in signal exceeds the threshold level until the gate opens. 28 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 29
Indicates the response for the compressor of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the compressor. F THRESHOLD Specifies the threshold level at which the compressor will operate. The input signal will start being compressed when the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 30
Indicates the response for the compander of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the compressor. F THRESHOLD Specifies the threshold level at which the compressor will operate. The input signal will start being compressed when the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 31
Indicates the response for the de-esser of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the de-esser. F THRESHOLD Specifies the threshold level at which the de-esser will operate. The input signal will start being compressed when the key-in - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 32
one used for direct out. NONE OMNI1-OMNI16 SLOT1-1, SLOT1-2...SLOT3-16 No assignment OMNI jacks 1-16 Output channels of an I/O card installed in slots 1-3 D DIRECT OUT POINT Selects the position at which direct out will be patched. Choose from PRE HPF or PRE EQ. 32 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 33
the fader knob, or set it to the nominal value (0.00 dB) by holding down the key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the input channel. This is linked with the INPUT section [CUE] keys on the M7CL's panel. 33 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 34
from which the signal is sent from the MIX channel to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off. The PRE POINT setting can be made in the Mixer Setup screen. HINT • If you are using MATRIX buses in stereo, the knob for the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 35
other. PAN Adjusts the panning of the signal that is sent from the MIX channel to each of the L/C/R channels. You can set this to the center position by holding down the < the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0-100%. 35 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 36
/off. C EQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the key TYPE I/TYPE II (EQ type) Selects either TYPE I (the algorithm used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. L - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 37
by holding down the key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the MIX channel. 3 37 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 38
are being used in stereo, the odd-numbered knob will be PAN. PAN (odd-numbered side) • If the FIXED type is selected for the MIX bus, only the ON button is valid. • The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen. 38 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 39
holding down the key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the MATRIX channel. 3 39 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 40
window ❏ CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a STEREO/MONO channel, this is the same as the channel selection for a MIX channel (➥ p.34). ❏ TO MATRIX These are the same as the TO MATRIX of a MIX channel (➥ p.34). 40 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 41
level is shown at the right of the fader, and the current value is shown in the numerical box immediately below. CCUE This button cue-monitors the signal of the STEREO/MONO channel. This is linked with the STEREO/MONO MASTER section [CUE] keys on the M7CL's panel. 41 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 42
desired library data, or copy desired library data to a library within the M7CL. This window is divided into DYNAMICS, INPUT EQ, OUTPUT EQ, EFFECT, and GEQ pages; to switch pages, click the tabs located at name Indicates the file name of the currently-open library. 42 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 43
neither of these indications cannot be recalled to this channel. K DYNAMICS (DYNAMICS page only) Select which of the two dynamics processors will be subject to the Store or Recall operation. L RACK No. (Rack selection) (Effect/GEQ page only) Select which rack will be subject to the Store or Recall - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 44
in this state, a dialog box will appear, asking you to confirm the Save operation. If you click the OK button, the copy-source scene(s) will be overwritten onto the library recall, store, copy, or move operation. You can click this repeatedly to repeat Undo and Redo. 44 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 45
switch pages, click the tabs shown in the upper part of the window. To display this window, choose [PATCH Editor] from the [Windows] menu, and select either " input channel. ❏ PRESET Initializes the patching in this page. ❏ CLEAR ALL Clears all patching in this page. 45 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 46
channel. INPUT INSERT PATCH page Output port selection Input port selection Here you can assign input/output ports to the insert-in/out of each input channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. 46 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 47
OUTPUT INSERT PATCH page Output port selection Input port selection Here you can assign input/output ports to the insert-in/out of each output channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. DIRECT OUTPUT PATCH - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 48
is the number and name of the output channel. You can click the channel name box to edit the name in this page. F Output port This shows the output port assigned to the output channel. You can click this box and choose the output port from the popup menu that appears. 48 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 49
Rack window Here you can make settings for GEQ, effects, and external head amps. This window is divided into GEQ/EFFECT and EXTERNAL HA pages; to switch pages, click the tabs located at the top of the window. GEQ/EFFECT page 1 2 3 45 6 49 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 50
INS MONO(C) MIX channel 1-16 insert in MATRIX channel 1-8 insert in Insert-in of STEREO channel L/R or the MONO channel (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. This is - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 51
select the insertion destination of GEQ, and edit the parameters. ARack No. (Rack selection) 1 Select the rack module that you want to control. BLIBRARY 2 This button accesses the GEQ library. Clicking this button will open the GEQ page of the LIBRARY window. 51 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 52
field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. The channel name is shown in the boxes immediately below. F Output meter This indicates the level of the signal that is being output to the currently selected GEQ module. 52 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 53
that can be operated. If you have operated fifteen bands, this number will be zero, and you won't be able to operate any additional bands. If you want to operate another band in this state, you'll need to return a previously-operated band back to the 0 dB position. 53 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 54
Rack module editor - Effect window Here you can select the effect type for an internal effect, edit the parameters, and specify the input/output patching. 54 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 55
STEREO channel L/R or the MONO channel (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. The channel name is shown in the boxes immediately below. 55 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 56
(Play/Record) buttons If "042 FREEZE" is selected as the effect type, you can use these buttons to record and play back the signal being input to the effect. Q Effect parameters This area shows the effect parameters and knobs for the currently selected effect type. 56 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 57
, this indicates the on/off status of the master phantom power supply. F Slots/Channels Here you can select the slots/channels to which the audio outputs of the external head amp device are connected. NONE SLOT1 1-8 SLOT1 9-16 SLOT2 1-8 SLOT2 9-16 SLOT3 1-8 SLOT3 9-16 57 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 58
, POST ON B PEAK HOLD Switches peak hold on/off. C Meters These peak level meters show the input level of each channel. The current fader value is shown in the box below. If clipping occurs at any one of the detection points in the channel, the ∑ segment will light. 58 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 59
OUTPUT METER page 1 2 3 A METERING POINT Select one of the following as the point where metering will occur. PRE EQ, PRE FADER, POST ON B PEAK HOLD This is the same as in the INPUT METER page. C Meters This is the same as in the INPUT METER page. 59 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 60
an assignment, click the desired grid. D CLEAR These buttons clear all channels assigned to the corresponding DCA group. When you click one of these buttons a window will appear, asking you to confirm the operation. To execute the Clear operation, click the OK button. 60 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 61
mute groups. E CLEAR These buttons clear all input channels and output channels assigned to the corresponding mute group. When you click one of these buttons a window will appear, asking you to confirm the operation. To execute the Clear operation, click the OK button. 61 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 62
in the Input Channels field of the Mixer Setup window, or during online editing with the M7CL-32 connected, up to sixteen groups can be assigned for INPUT CH 1-32, and you'll be able to choose from link groups A-R. B CLEAR ALL Clears the link settings for all channels. 62 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 63
module output on/off (*) INPUT CH 33-48 can be viewed only if 48 is selected in the Input Channels field of the Mixer Setup window when editing offline, or when editing online with the M7CL-48. D SEND PARAMETER Specify the link status for each MIX/MATRIX SEND bus. 63 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 64
Here you can manage scene memories, and make various settings related to scene recall operations. This window is divided into SCENE MEMORY, RECALL SAFE, and FADE TIME pages. To switch pages, click the tabs shown in the upper part of the window. SCENE MEMORY page Here you can edit the M7CL's scene - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 65
effect settings will be recalled Internal head amp and external head amp settings will be recalled Input patch settings will be recalled Output patch settings will be recalled Input channels (INPUT, ST IN, DCA) settings will be recalled except for head amp settings Output channel (MIX, MATRIX - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 66
P Q R S N INTERNAL DATA This area shows the M7CL's scene memory contents. The items displayed are the same as UNDO Cancels the last-performed scene recall, store, copy, or move operation. S PROTECT Turns on the Protect setting for the scene(s) selected in the list. 66 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 67
will be excluded. D SET ALL These buttons turn on all buttons for all input channels or ST IN channels, or for the corresponding parameter. E CLEAR ALL These buttons turn off all buttons for all input channels or ST IN channels, or for the corresponding parameter. 54 67 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 68
for patching, DCA groups, and racks. H INPUT PATCH This on/off button specifies whether INPUT PATCH settings will be excluded from recall operations. I INPUT NAME This on/off button specifies whether the channel names of input channels will be excluded from recall operations. J OUTPUT NAME This on/off - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 69
which fader CHANNEL FADING ENABLE These on/off buttons select the input channels that will be excluded from recall operations. B SET ALL This button switches on the buttons of all input channels. C CLEAR ALL This button switches off the buttons of all input channels. 69 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 70
the buttons of all output channels. G FADING ENABLE This button enables/disables the Fade function for the faders of the current scene. H FADE TIME Drag this knob in the screen to adjust the fade time. The current value is shown in the numerical box immediately below. 70 M7CL Editor Owner's Manual - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 71
window Opens the ST IN window Opens the MIX window Opens the MATRIX window Opens the STEREO/MONO window Opens the MATRIX window Opens the Selected Channel window Opens the Library window Opens the Patch Editor window Opens the Rack window Opens the Meter window Opens the Group/Link window Opens the - Yamaha M7CL | M7cl V1 Editor Owner's Manual - Page 72
28 HA GAIN/Ø/HP 25 Input channel 23 INSERT 32 MATRIX channel 38 MIX channel 34 MIX/MATRIX SEND 25 Pan / Fader 37 RECALL SAFE/MUTE SAFE ...33 STEREO/MONO channel ........40 To MATRIX 34 TO STEREO/MONO .........26, 35 Sessions 6 SET ALL 67-70 Setup Mixer 3 System 2 ST IN window 14 STEREO
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
 |
 |
M7CL Editor Owner’s Manual
1
Special Notices
•
The software and this owner’s manual are the exclu-
sive copyrights of Yamaha Corporation.
•
Copying of the software or reproduction of this
manual in whole or in part by any means is expressly
forbidden without the written consent of the manu-
facturer.
•
Copying of the commercially available music
sequence data and/or digital audio files is strictly
prohibited except for your personal use.
•
Yamaha makes no representations or warranties
with regard to the use of the software and documen-
tation and cannot be held responsible for the results
of the use of this manual and the software.
•
The screen displays as illustrated in this owner’s
manual are for instructional purposes, and may
appear somewhat different from the screens which
appear on your computer.
•
Future upgrades of application and system software
and any changes in specifications and functions will
be announced separately.
•
The company names and product names in this
Owner’s Manual are the trademarks or registered
trademarks of their respective companies.
❏
Yamaha Pro Audio Global Site
Contents
Getting Started
.........................................
2
Master window
.........................................
9
Overview window
...................................
11
Selected Channel window
.......................
23
Library window
.......................................
42
Patch Editor window
...............................
45
Rack window
...........................................
49
Meter window
.........................................
58
Group/Link window
................................
60
Scene window
.........................................
64
Keyboard Shortcuts
.................................
71
Index
........................................................
72
*
Specifications and descriptions in this owner ’s manual are
for information purposes only. Yamaha Corp. reserves the
right to change or modify products or specifications at any
time without prior notice.
M7CL Editor
M7CL Editor
M7CL Editor
Owner’s Manual
Owner’s Manual
Owner’s Manual