Yamaha M7CL M7cl V3 Editor Owner's Manual (v3.5.x)
Yamaha M7CL Manual
 |
View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha M7CL manual content summary:
- Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 1
2 Master window 13 Overview window 16 Selected Channel window 29 Library window 49 Patch Editor window 52 Rack window 56 Meter window 65 Group/Link window 67 Scene window 71 User Defined Keys Setup window........... 78 Sends On Fader window 79 Output Port window 80 Keyboard Shortcuts - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 2
Started Overview of M7CL V3 Editor M7CL V3 Editor (hereinafter called "M7CL Editor" in this document) enables you to remotely control a Yamaha M7CL mixing console (Version 3) (such as M7CL-48ES, M7CL-48, or M7CL-32; hereinafter collectively called "M7CL" in this document). M7CL Editor also enables - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 3
determines whether or not using the USER DEFINED KEYS on the console enables you to remotely open and close the M7CL Editor windows. F Level Meter By disabling the meter function you can reduce the processing load caused by screen drawing and communication. This option specifies whether the level - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 4
the Mixer Setup dialogbox, choose [Mixer Setup] from the [File] menu. 1 2 A Mix Bus Setup Here you can make settings relating to the MIX buses. Signal Type: Choose either MONOx2 or STEREO for each two adjacent odd-numbered/even-numbered MIX buses. Bus Type/Send Point: Choose either VARI (PRE FADER - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 5
Password Enter the Administrator password that was specified on the M7CL console. This is not required if no Administrator password has been specified on the M7CL console, but if this password is incorrect you will be asked to enter it when the user key is read. 5 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 6
SETUP MIXER SETUP: Change the privileges for making mixer setup settings. OUTPORT SETUP: Change the privileges for making outport setup settings. MIDI: Change the privileges for making MIDI settings. O Create Creates the user key. P Cancel Closes the dialogbox. 6 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 7
once you save these files on the M7CL V3 console or Editor, you will not be able to open them on the other version of M7CL console or Editor. NOTE If you use the M7CL-48ES console to open a session saved via the M7CL-32/48 console, or if you use the M7CL-32/48 console to open a session saved via the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 8
ES IN 1-16 ES IN 17-32 ES IN 33-48 TALKBACK SLOT1 OUT 1-16 ES OUT 1-16 SLOT2 OUT 1-8 9-16 → ES OUT 17-24 → OMNI OUT 1-8 No assignment → SLOT2 OUT 1-16 SLOT3 OUT 1-16 → SLOT3 OUT 1-16 2TR DIGITAL OUT → 2TR DIGITAL OUT (*) The same HA settings will be used. 8 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 9
DIGITAL OUT (*) The same HA settings will be used. D M7CL-48ES ➞ Using External HA via Slot Converts the patch settings as follows: SLOT1 IN 1-16 SLOT2 IN 1-16 SLOT3 IN 1-16 OMNI IN 1-8 INPUT 1-16 INPUT 17-32 INPUT 33-48 ST IN 1L-4R ES IN 1-16 →(*) SLOT1 IN 1-16 ES IN 17-32 ES IN 33-48 - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 10
successfully undo or redo any previous operation: • Operations on the M7CL console • Quitting Studio Manager • Synchronizing with the M7CL console • Session operations NOTE You cannot Undo or Redo the following operations: • Edits in the Setup window • Synchronization • Opening and closing the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 11
each window from the [Windows] menu. For the INPUT CH window and Effect Editor window, use the sub-menu to select the channels or library you want to see. You can choose Tile or Cascade to arrange the windows within the editor. ● Tile ● Cascade In the Library window or Scene window, click the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 12
Setup setting of the M7CL-48ES unit, remove the check from the checkbox. Console ➔ PC: Transfers the current parameter settings of your console to the M7CL Editor. 3 Click [OK]. Do not operate the console while synchronization is in progress. NOTE If you use the "Recall" function in Studio Manager - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 13
. When SENDS ON FADER mode is engaged, the Sends On Fader window appears. (➥ p.79) If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is selected, this parameter will be linked with the SEND ON FADER mode setting on the M7CL console. 13 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 14
12) This indicator is shown when M7CL Editor is correctly connected to the M7CL itself. In this state, the parameters of M7LC Editor and the M7CL itself are linked. This indicator is shown when M7CL Editor and the M7CL itself are not connected, or when there is a problem with the connection, or when - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 15
MATRIX window. H [33-48] button Opens the INPUT CH 33-48 window. This button is available during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It is also available during online editing for the M7CL-48 or M7CL-48ES. 15 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 16
button(*) ● On the M7CL itself, assign one of the USER DEFINED KEYS to [1-16]/[17-32]/[33-48](*) in [INPUT CH] of [M7CL EDITOR CONTROL], and execute the function (*) INPUT CH 33-48 can be viewed during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It can - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 17
Channel window of the corresponding channel. To open the Selected Channel MIX buses, the bar graph is fixed at nominal level (0 dB), and only the on/off status is shown. NOTE In SENDS ON FADER mode, this button enables you to adjust the send level using the fader. 17 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 18
want to perform operations. This is linked with the INPUT section [SEL] keys on the M7CL console panel. NOTE If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. M CUE P This button cue-monitors the signal - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 19
If you hold down the (< >) key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. Q Channel name This is a text box that displays the channel name. You can also edit the channel name in this text box. 19 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 20
ST IN window ( M7CL-32/M7CL-48 only) In this window you can view and edit the mix parameters of ST IN channels 1-4. The parameters shown in the window can be selected from the [View] menu or the menu that appears when you right-click ( key + click) in the window. You can access this - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 21
IN section [SEL] keys on the M7CL's panel. J K L NOTE If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. K CUE M This button cue-monitors the signal of the ST IN channel (L/R are linked). This is linked - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 22
MIX channel, from the 2 following choices. ES 1-ES24(M7CL-48ES) EtherSound output channels 1-24 OMNI1-OMNI8 OMNI OUT jacks 1-8 3 OMNI9-OMNI16(M7CL-32/48) OMNI OUT jacks 9-16 SLOT1-1, SLOT1-2...SLOT3-16 Input channels of an I/O card /disables the insert-in. 22 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 23
Mute Safe status of the channel. The fader is color-coded and indicates status as follows: White: You can adjust the input level of the MIX channel (normal mode). Gray: MIX channel is off. Other colors: You can adjust the send level (SENDS ON FADER mode). 23 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 24
appears when you right-click ( key + click) in the window. You can access this window in the following ways. ● From the [Windows] menu, choose [Overview] and then choose "MATRIX" ● Use the navigation keys in the Master window to turn on the [MTRX] button 24 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 25
is sent from each channel to the MATRIX bus. The method of operation and the meaning of the display are the same as for (5) MATRIX in the MIX window 2 (➥ p.23). (*) INPUT CH 33-48 can be viewed during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 26
The L/R settings are linked.) D MATRIX SEND Here you can view and edit the send levels of the signals sent from the STEREO/MONO channel to MATRIX 1-8 bus. The method of operation and the meaning of the display are the same as for MATRIX in the MIX window (➥ p.23). 26 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 27
the channel number (ST or M). You can double-click this number to open the Selected Channel window for this channel. If you hold down the (< >) key of your computer keyboard and double-click this, the Selected Channel window will open as an additional view. 27 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 28
, the R character at the lower right of the fader is dis- 4 played in green. D DCA number 5 This is the number of the DCA group. E DCA group name This is a text box that displays the DCA group name. You can also edit the DCA group name in this text box. 28 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 29
channels. (*) INPUT CH 33-48 can be viewed during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL-48ES. If an input channel is selected ● INPUT CH window 29 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 30
edit the channel name in the text box. B LIBRARY Accesses the Input Channel Library. Click this button to open the INPUT CH page of the Library window. C INPUT PATCH Selects the input source assigned to the input channel (for the selectable input sources, ➥ p.16). 30 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 31
in the Mixer Setup dialogbox. D Channel name This section indicates the name of the MIX channel or MATRIX channel. ❏ HA GAIN/Ø/HPF 1 2 3 A HA (HA Gain) Adjusts the gain of the internal head amp or of the external head amp (e.g., Yamaha AD8HR, SB168-ES) patched to the input channel. The current - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 32
the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. CSR (Center Side Ratio) Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0-100%. 32 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 33
on/off. C EQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the (< >) either TYPE I (the algorithm used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. 33 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 34
Specifies the amount by which the signal is attenuated while the gate is closed. H DECAY Specifies the time over which the gate will close after the hold time has elapsed. I ATTACK Specifies the time from when the key-in signal exceeds the threshold level until the gate opens. 34 M7CL V3 Editor Owner - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 35
Indicates the response for the compressor of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the compressor. F THRESHOLD Specifies the threshold level at which the compressor will operate. The input signal will start being compressed when the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 36
Indicates the response for the compander of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the compressor. F THRESHOLD Specifies the threshold level at which the compressor will operate. The input signal will start being compressed when the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 37
Indicates the response for the de-esser of the currently selected channel. E GR meter This meter indicates the amount of gain reduction produced by the de-esser. F THRESHOLD Specifies the threshold level at which the de-esser will operate. The input signal will start being compressed when the key-in - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 38
channels of an I/O card installed in slots 1-3 L/R inputs of Rack 1-8 D POINT (Insert point) Selects the position at which insert-in/out will be patched. Choose from PRE EQ, PRE FADER, or POST ON. E HA gain (M7CL-48ES down the (< >) key and clicking the knob. 38 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 39
the fader knob, or set it to the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the input channel. This is linked with the INPUT section [CUE] keys on the M7CL's panel. 39 M7CL V3 Editor Owner - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 40
as the position from which the signal is sent from the MIX 4 channel to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off. The PRE POINT setting can be made in the Mixer Setup dialogbox. NOTE Right-click the PRE button to display a context - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 41
PAN ST MONO BALANCE Adjusts the panning of the signal sent from the MIX channel to the STEREO bus L/R channels. You can set this to the center position by holding down the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0-100%. 41 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 42
Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. L ATT (Attenuation) Adjusts the amount of attenuation/gain. 42 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 43
the (< >) key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the MIX channel. 3 43 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 44
box immediately below. B PRE(PRE/POST) These select either PRE or POST as the position from which the signal is sent from the MIX buses or STEREO/ MONO buses to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off. 44 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 45
and the VARI type / FIXED type setting can be made in the Mixer Setup dialogbox. D Channel name This section indicates the name of the MIX channel or STEREO/MONO channel. ❏ BALANCE This is shown only if the selected MATRIX bus is being used as stereo. It adjusts the left/right volume balance of the - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 46
the (< >) key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the fader knob. C CUE This button cue-monitors the signal of the MATRIX channel. 46 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 47
window ❏ CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a STEREO/MONO channel, this is the same as the channel selection for a MIX channel (➥ p.40). ❏ TO MATRIX These are the same as the TO MATRIX of a MIX channel (➥ p.40). 47 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 48
level is shown at the right of the fader, and the current value is shown in the numerical box immediately below. C CUE This button cue-monitors the signal of the STEREO/MONO channel. This is linked with the STEREO/MONO MASTER section [CUE] keys on the M7CL's panel. 48 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 49
desired library data, or copy desired library data to a library within the M7CL. This window is divided into DYNAMICS, INPUT EQ, OUTPUT EQ, EFFECT, GEQ, INPUT CH, and OUTPUT CH pages; to switch pages, click name Indicates the file name of the currently-open library. 49 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 50
neither of these indications cannot be recalled to this channel. K DYNAMICS (DYNAMICS page only) Select which of the two dynamics processors will be subject to the Store or Recall operation. L RACK No. (Rack selection) (Effect/GEQ page only) Select which rack will be subject to the Store or Recall - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 51
in this state, a dialog box will appear, asking you to confirm the Save operation. If you click the OK button, the copy-source scene(s) will be overwritten onto the library recall, store, copy, or move operation. You can click this repeatedly to repeat Undo and Redo. 51 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 52
switch pages, click the tabs shown in the upper part of the window. To display this window, choose [PATCH Editor] from the [Windows] menu, and select either input channel. ❏ PRESET Initializes the patching in this page. ❏ CLEAR ALL Clears all patching in this page. 52 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 53
. INPUT INSERT PATCH page Output port selection Input port selection Here you can assign input/output ports to the insert-in/out of each input channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. 53 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 54
to the insert-in/out of each output channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. DIRECT OUTPUT PATCH page Here you can select the output port that will directly output each input channel. 54 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 55
the channel name box to edit the name in this page. F Output port This shows the output port assigned to the output channel. You can click this box, then choose or cancel the output port from the popup menu that appears. NOTE You can assign multiple output ports. 55 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 56
you can make settings for GEQ, effects, and external head amps. This window is divided into GEQ/EFFECT and EXTERNAL HA page (M7CL-32/48) or EXT-ES HA page (M7CL48ES). To switch pages, click the tabs located at the top of the window. GEQ/EFFECT page 1 2 3 45 6 56 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 57
channel 1-8 STEREO channel L/R, MONO channel INPUT CH 1-48(*) insert in MIX channel 1-16 insert in MATRIX channel 1-8 insert in Insert-in of STEREO channel L/R or the MONO channel (*) INPUT CH 33-48 can be viewed during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 58
the insertion destination of GEQ, and edit the parameters. A Rack No. (Rack selection) 1 Select the rack module that you want to control. B LIBRARY 2 This button accesses the GEQ library. Clicking this button will open the GEQ page of the LIBRARY window. 58 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 59
Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL48ES. The channel name is shown in the boxes immediately below. F Output meter This indicates the level of the signal that is being output to the currently selected GEQ module. 59 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 60
that can be operated. If you have operated fifteen bands, this number will be zero, and you won't be able to operate any additional bands. If you want to operate another band in this state, you'll need to return a previously-operated band back to the 0 dB position. 60 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 61
Rack module editor - Effect window Here you can select the effect type for an internal effect, edit the parameters, and specify the input/output patching. 61 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 62
(*) INPUT CH 33-48 can be viewed during offline editing only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL-48ES. The channel name is shown in the boxes immediately below. 62 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 63
(Play/Record) buttons If "042 FREEZE" is selected as the effect type, you can use these buttons to record and play back the signal being input to the effect. Q Effect parameters This area shows the effect parameters and knobs for the currently selected effect type. 63 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 64
phantom power supply. F Slots/Channels Here you can select the slots/channels to which the audio outputs of the external head amp device are connected. On the M7CL-48ES, the EXT-ES HA assignment is fixed. NONE SLOT1 1-8 SLOT1 9-16 SLOT2 1-8 SLOT2 9-16 SLOT3 1-8 SLOT3 9-16 64 M7CL V3 Editor Owner - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 65
POST ON B PEAK HOLD Switches peak hold on/off. C Meters These peak level meters show the input level of each channel. The current fader value is shown in the box below. If clipping occurs at any one of the detection points in the channel, the ∑ segment will light. 65 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 66
OUTPUT METER page 1 2 3 A METERING POINT Select one of the following as the point where metering will occur. PRE EQ, PRE FADER, POST ON B PEAK HOLD This is the same as in the INPUT METER page. C Meters This is the same as in the INPUT METER page. 66 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 67
assignment, click the desired grid. D CLEAR These buttons clear all channels assigned to the corresponding DCA group. When you click one of these buttons a window will appear, asking you to confirm the operation. To execute the Clear operation, click the OK button. 67 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 68
groups. E CLEAR These buttons clear all input channels and output channels assigned to the corresponding mute group. When you click one of these buttons a window will appear, asking you to confirm the operation. To execute the Clear operation, click the OK button. 68 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 69
M7CL-32 is selected in the System Setup dialogbox, or during online editing with the M7CL-32 connected, up to sixteen groups can be assigned for INPUT CH 1-32, and you'll be able to choose from link groups A-R. B CLEAR ALL Clears the link settings for all channels. 69 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 70
the System Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL-48ES. NOTE The HA and FADER parameters will maintain level differences between linked channels. D SEND PARAMETER Specify the link status for each MIX/MATRIX SEND bus. 70 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 71
Here you can manage scene memories, and make various settings related to scene recall operations. This window is divided into SCENE MEMORY, RECALL SAFE, and FADE TIME pages. To switch pages, click the tabs shown in the upper part of the window. SCENE MEMORY page Here you can edit the M7CL's scene - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 72
effect settings will be recalled Internal head amp and external head amp settings will be recalled Input patch settings will be recalled Output patch settings will be recalled Input channels (INPUT, ST IN, DCA) settings will be recalled except for head amp settings Output channel (MIX, MATRIX - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 73
P Q R S O INTERNAL DATA This area shows the M7CL's scene memory contents. The items displayed are the same as UNDO Cancels the last-performed scene recall, store, copy, or move operation. T PROTECT Turns on the Protect setting for the scene(s) selected in the list. 73 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 74
be excluded. D SET ALL These buttons turn on all buttons for all input channels or ST IN channels, or for the corresponding parameter. E CLEAR ALL These buttons turn off all buttons for all input channels or ST IN channels, or for the corresponding parameter. 54 74 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 75
for patching, DCA groups, and racks. H INPUT PATCH This on/off button specifies whether INPUT PATCH settings will be excluded from recall operations. I INPUT NAME This on/off button specifies whether the channel names of input channels will be excluded from recall operations. J OUTPUT NAME This on/off - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 76
fader CHANNEL FADING ENABLE These on/off buttons select the input channels that will be excluded from recall operations. B SET ALL This button switches on the buttons of all input channels. C CLEAR ALL This button switches off the buttons of all input channels. 76 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 77
buttons of all output channels. G FADING ENABLE This button enables/disables the Fade function for the faders of the current scene. H FADE TIME Drag this knob in the screen to adjust the fade time. The current value is shown in the numerical box immediately below. 77 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 78
only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL-48ES. A CURRENT USER Displays the name of the user currently logged into the M7CL console. If the M7CL has not yet been synchronized with the Editor, this - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 79
the send level off or on, and adjust the send level using the [ON] button and fader for the input channel displayed in the Overview window. NOTE For MATRIX bus send, not only the input channels but MIX channels and STEREO/MONO channels can be in SEND ON FADER mode. 79 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 80
the channel is assigned. D Channel select button This button lets you select the channel that is assigned to the output port. E Channel name Indicates the name of the channel that is assigned to the corresponding output port. F DELAY button Switches the output port delay on/off. 80 M7CL V3 Editor - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 81
. You can adjust the setting in 0.1 dB steps over a range of -96 to +24 dB. The current value is shown immediately below the knob. K Level meter This meter indicates the level of the signal assigned to the output port. 81 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 82
only if "M7CL-48" or "M7CL-48ES" is selected in the System Setup dialog box. It can also be viewed during online editing for the M7CL-48 or M7CL-48ES. (**) Modify or cancel the shortcut assignment for the Universal Access Zoom function, or use the number key . 82 M7CL V3 Editor Owner's Manual - Yamaha M7CL | M7cl V3 Editor Owner's Manual (v3.5.x) - Page 83
/Ø/HP 31 Input channel 29 INSERT 38 MATRIX channel 44 MIX channel 40 MIX/MATRIX SEND 31 Pan / Fader 43 RECALL SAFE/MUTE SAFE ...39 STEREO/MONO channel ........47 To MATRIX 40 TO STEREO/MONO .........32, 41 Sends On Fader window 79 Sessions 7 SET ALL 74-77 Setup Mixer 4 System 2 ST IN
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
 |
 |
M7CL V3 Editor Owner’s Manual
1
Special Notices
•
The software and this owner’s manual are the exclu-
sive copyrights of Yamaha Corporation.
•
Copying of the software or reproduction of this
manual in whole or in part by any means is expressly
forbidden without the written consent of the manu-
facturer.
•
Copying of the commercially available music
sequence data and/or digital audio files is strictly
prohibited except for your personal use.
•
Yamaha makes no representations or warranties
with regard to the use of the software and documen-
tation and cannot be held responsible for the results
of the use of this manual and the software.
•
The screen displays as illustrated in this owner’s
manual are for instructional purposes, and may
appear somewhat different from the screens which
appear on your computer.
•
For information on modification of system soft-
ware, certain functions, or specifications due to ver-
sion update of the application, please visit the
following website:
•
Windows is a registered trademark of Microsoft
Corporation in the U.S. and other countries.
•
Apple, Mac and Macintosh are trademarks of Apple
Inc., registered in the U.S. and other countries.
•
The company names and product names in this
Owner’s Manual are the trademarks or registered
trademarks of their respective companies.
❏
Yamaha Pro Audio Global Site
Contents
Getting Started
.........................................
2
Master window
.......................................
13
Overview window
...................................
16
Selected Channel window
.......................
29
Library window
.......................................
49
Patch Editor window
...............................
52
Rack window
...........................................
56
Meter window
.........................................
65
Group/Link window
................................
67
Scene window
.........................................
71
User Defined Keys Setup window
...........
78
Sends On Fader window
.........................
79
Output Port window
...............................
80
Keyboard Shortcuts
.................................
82
Index
........................................................
83
*
Specifications and descriptions in this owner ’s manual are
for information purposes only. Yamaha Corp. reserves the
right to change or modify products or specifications at any
time without prior notice.
M7CL V3 Editor
M7CL V3 Editor
M7CL V3 Editor
Owner’s Manual
Owner’s Manual
Owner’s Manual
Version 3.5
Version 3.5
Version 3.5
Description of menus and buttons
In the event that menu and button names on a Windows
system are different from those on a Mac, this manual
uses the Windows menu and button names followed by the
Mac menu and button names in parentheses.