Yamaha SWR2311P-10G SWR2311P-10G Command Reference
Yamaha SWR2311P-10G Manual
 |
View all Yamaha SWR2311P-10G manuals
Add to My Manuals
Save this manual to your list of manuals |
Yamaha SWR2311P-10G manual content summary:
- Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 1
Yamaha L2 Switch Intelligent L2 PoE SWR2311P-10G Command Reference Rev.2.02.14 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 2
2 | Command Reference | TOC Contents Preface: Introduction 12 Chapter 1: How to read the command reference 13 1.1 Applicable firmware revision ...13 1.2 How to read the command reference ...13 1.3 Interface names ...13 1.4 Input syntax for commands starting with the word "no 14 Chapter 2: How to - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 3
4.5.2 Show operating information ...38 4.5.3 Show currently-executing processes 38 4.5.4 Show technical support information 39 4.5.5 Save technical support information 40 4.6 Time management ...40 4.6.1 Set clock manually ...40 4.6.2 Set time zone ...41 4.6.3 Show current time ...41 4.6.4 Set NTP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 4
4 | Command Reference | TOC 4.10.10 Show SNMP view settings ...57 4.10.11 Show SNMP group settings ...57 4.10.12 Show SNMP user settings ...58 4.11 RMON ...58 4.11.1 Set RMON function ...58 4.11.2 Set RMON Ethernet statistical information group 59 4.11.3 Set RMON history group ...59 4.11.4 Set RMON - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 5
status ...90 4.19.19 Show information for connected devices of all interfaces 93 4.19.20 Clear LLDP frame counters ...94 4.20 L2MS (Layer 2 management service) settings 94 4.20.1 Move to L2MS mode ...94 4.20.2 Set L2MS function ...94 4.20.3 Set role of L2MS function ...95 4.20.4 Set L2MS slave - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 6
6 | Command Reference | TOC 4.23.3 Initialize settings ...107 4.23.4 Mount SD card ...108 4.23.5 Unmount SD card ...108 4.23.6 Set default LED mode ...108 4.23.7 Show LED mode ...109 4.23.8 Show port error LED status ...109 4.23.9 Backup system information ...110 4.23.10 Restore system information - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 7
Command Reference | TOC | 7 5.3.13 Set the guest VLAN ...140 5.3.14 Suppression period settings following failed authentication 141 5.3.15 Set reauthentication interval ...141 5.3.16 Set the reply wait time for the RADIUS server overall 142 5.3.17 Set supplicant reply wait time 142 5.3.18 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 8
8 | Command Reference | TOC 6.2.9 Set native VLAN for trunk port (tagged port 166 6.2.10 Set private VLAN port type ...167 6.2.11 Set private VLAN host port ...167 6.2.12 Set promiscuous port for private VLAN 168 6.2.13 Set voice VLAN ...169 6.2.14 Set CoS value for voice VLAN 170 6.2.15 Set DSCP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 9
Command Reference | TOC | 9 7.2 IPv4 route control ...196 7.2.1 Set static IPv4 route ...196 7.2.2 Show IPv4 Forwarding Information Base 197 7.2.3 Show IPv4 Routing Information Base 197 7.2.4 Show summary of the route entries registered in the IPv4 Routing Information Base 198 7.3 ARP ...198 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 10
map ...234 9.1.17 Show VLAN access map filter 234 9.2 QoS (Quality of Service) ...235 9.2.1 Enable/disable QoS ...235 9.2.2 Set default CoS ...235 9.2.3 Set 241 9.2.10 Specify egress queue of frames transmitted from the switch itself 241 9.2.11 Generate class map (traffic category conditions - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 11
Command Reference | TOC | 11 9.2.22 Apply policy map for received frames 248 9.2.23 Set pre-marking (CoS) ...249 9.2.24 Set pre-marking (TOS precedence 250 9.2.25 Set pre-marking (DSCP) ...251 9.2.26 Set individual policers (single rate 251 9.2.27 Set individual policers (twin rate 253 9.2.28 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 12
part or in whole is prohibited. • The contents of this document are subject to change without notice. • Yamaha disclaims all responsibility for any damages caused by loss of data or other problems resulting from the use of this product. The warranty is limited to this physical product itself. Please - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 13
firmware Yamaha Intelligent L2 Switch SWR2311P of Rev.2.02.14. For the latest firmware released after printing of this command reference, manuals, and "stack ID" + "." + "port number" after the port number. * The SWR2311P-10G is fixed as stack ID=1. When specifying LAN port #1 on LAN port stack #1 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 14
14 | Command Reference | How to read the command reference Interface type Prefix LACP logical interface po Description Specify sa or po followed by "logical interface ID". Examples To specify LACP logical interface #2: po2 1.4 Input syntax for commands starting with the word "no" Many - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 15
-45/DB-9 console cable when making settings from a terminal that is connected to the CONSOLE port of SWR2311P. For the USB cable connected to the mini-USB CONSOLE port, use a USB cable that supports data communication between a USB Type A connector and a mini-USB Type B (5-pin) connector. Cables for - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 16
user name and password using the username command. The SSH server settings of the SWR2311P are as follows. • Access to an SSH server can be controlled for each . • Note that the following functions are not supported. • SSH protocol version 1 • User authentication aside mode service terminal-length - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 17
and then make TFTP server settings. The IP address settings of the SWR2311P are as follows. • The default IPv4 address setting is ip address dhcp IPv4 address, use the ip address command. The TFTP server settings of the SWR2311P are as follows. • With the default settings of the TFTP server function - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 18
log in without a password. • Login screen Username: Password: • Console screen following login SWR2311P Rev.2.02.06 (Tue Mar 13 08:41:39 2018) Copyright (c) 2018 Yamaha Corporation. All Rights Reserved. SWR2311P> 2.4 Command input mode 2.4.1 Command input mode basics In order to change the settings - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 19
command to specify the host name. In cases where multiple SWR2311P units are used, management will be easier if separate names are assigned to each switch. Changing the host name SWR2311P(config)# hostname Switch-012 Switch-012(config)# 2.4.4 Executing commands of a different input mode Because the - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 20
same operation as the end command. 2.5.2 Command help By entering '?' in the command line you can search for the available commands or parameters. SWR2311P#show vlan ? VLAN id access-map Show VLAN Access Map brief VLAN information for all bridges (static and dynamic) filter Show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 21
filter, restricting the content that is shown in the screen and making it easier for you to see the desired information. The SWR2311P provides the following three modifiers for the show command. Modifiers Description include grep Output only the lines that include the specified character string - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 22
22 | Command Reference | How to use the commands Discarding % port1.1: Port Number 905 - Ifindex 5001 - Port Id 0x8389 - Role Disabled State Forwarding % port1.2: Port Number 906 - Ifindex 5002 - Port Id 0x838a - Role Disabled State Forwarding % port1.3: Port Number 907 - Ifindex 5003 - Port Id - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 23
or modified, the settings or modifications are lost. Please be aware of this. 3.2 Default setting values The default setting values for the SWR2311P are shown in the table below. • Default setting values for the entire system Category Setting item CONFIG CONFIG used at startup Console timeout - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 24
Firmware update LLDP L2MS SYSLOG Access control Maintenance VLAN L2 switching DNS cliant Interface control Traffic control Web GUI • L2MS filter Default value firmware-update url http:// www.rtpro.yamaha.co.jp/firmware/ revision-up/swr2311p.bin don't allow 300 sec enabled enabled enabled slave OFF - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 25
Category L2 switching Traffic control PoE power supply LLDP agent • Settings for the default VLAN (vlan1) • IPv4 Address : DHCP cliant • IGMP Snooping: Enable • Querier : Disable • Fast-Leave : Disable • - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 26
configuration settings from the command line. [Example] Specify user1234 as the unnamed user password. SWR2311P(config)#password user1234 Delete the unnamed user password. SWR2311P(config)#no password 4.1.2 Set administrator password [Syntax] enable password password no enable password [Parameter - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 27
)#enable password admin1234 Delete the administrator password. SWR2311P(config)#no enable password 4.1.3 Encrypt password [Syntax] password-encryption switch no password-encryption [Parameter] switch : Set password encryption enable disable Setting value Encrypt Don't encrypt Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 28
Command Reference | Maintenance and operation functions [Parameter] switch : Allow login by special password enable disable Setting value Enable login with special password. SWR2311P(config)#force-password enable Disable login with special password. SWR2311P(config)#no force-password 4.2 User - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 29
making configuration settings from the command line. [Example] Set the user "user1234". SWR2311P(config)#username user1234 Grant privileges to user user1234 and specify a password. SWR2311P(config)#username user1234 privilege on password user_pass 4.2.2 Show login user information [Syntax] show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 30
Mar 13 08:41:39 2018) Copyright (c) 2018 Yamaha Corporation. All Rights Reserved. SWR2311P>enable SWR2311P#configure terminal Enter configuration commands, one per line. SWR2311P(config)#banner motd Hello World! SWR2311P(config)#exit SWR2311P#exit End with CNTL/Z. Username: Password: Hello World - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 31
is in the SD card produces an error. [Example] Save the running configuration. SWR2311P#copy running-config startup-config Succeeded to write configuration SWR2311P# 4.3.2 Save running configuration [Syntax] write [config_num] [Parameter] config_num : Configuration number Setting value sd - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 32
write Succeeded to write configuration. SWR2311P# 4.3.3 Show the running configuration [Syntax] show running-config [section] [Parameter] section : Section to be shown access-list http-server interface ip ipv6 key l2ms lldp snmp spanning-tree ssh-server switch telnet-sever Setting value [Input - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 33
this command on a config that is in the SD card produces an error. [Example] Show the startup configuration on the next startup. SWR2311P#show startup-config ! ! Last Modified: 00:00:00 JST Mon Jan 01 2018 ! interface port1.1 switchport switchport mode access no shutdown ! ... ! interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 34
that is in the SD card produces an error. [Example] Copy startup config #0 to startup config #1. SWR2311P#copy startup-config 0 1 Succeeded to copy configuration SWR2311P# 4.3.7 Set description for startup config [Syntax] startup-config description config_num line no startup-config description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 35
SD card on which a startup config is saved is not inserted, startup config #0 is selected. [Example] Select startup config #1 and restart. SWR2311P#startup-config select 1 reboot system? (y/n): y 4.4 Manage boot information 4.4.1 Show boot information [Syntax] show boot num show boot all show boot - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 36
EXEC mode [Description] Clears the boot information history. [Example] Clear the boot information. SWR2311P#clear boot list 4.4.3 Set SD card boot [Syntax] boot prioritize sd switch [Parameter] switch : Enable or disable SD card boot Setting enable disable Description Enable SD card boot - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 37
Item Description NAME Name DESCR Description Vendor Vendor name PID Product ID VID Version ID, 0 if invalid SN Serial number [Example] Show inventory information. SWR2311P>show inventory NAME: L2 PoE switch DESCR: SWR2311P-10G Vendor: Yamaha PID: SWR2311P-10G VID: 0000 SN: S00000000 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 38
time • Elapsed time from boot • Temperature status • Temperature [Example] Show operating information. SWR2311P>show environment SWR2311P-10G BootROM Ver.1.00 SWR2311P Rev.2.02.06 (Tue Mar 13 08:41:39 2018) main=SWR2311P-10G ver=00 serial=S00000000 MAC-Address=00a0.de00.0000 CPU: 7%(5sec) 8%(1min - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 39
• show ipv6 route database • show arp • show ipv6 neighbors • show ip igmp snooping groups • show ip igmp snooping interface [Example] Show technical support information. SWR2311P#show tech-support # # Information for Yamaha Technical Support # *** show running-config *** ! dns-client enable ! ... - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 40
command was executed [Note] The SD card must be inserted in advance. [Example] Save technical support information to the SD card. SWR2311P#copy tech-support sd SWR2311P# 4.6 Time management 4.6.1 Set clock manually [Syntax] clock set time month day year [Parameter] time : hh:mm:ss Time month - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 41
[Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description] Shows the current time, year, month, and date. [Example] Show current time. SWR2311P>show clock Thu Jan 1 00:00:00 JST 2015 4.6.4 Set NTP server [Syntax] ntpdate server ipv4 ipv4_addr ntpdate server ipv6 ipv6_addr ntpdate - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 42
(config)#ntpdate server ipv6 fe80::2a0:deff:fe11:2233%vlan1 Specify ntp.example.com as the NTP server. SWR2311P(config)#ntpdate server name ntp.example.com 4.6.5 Synchronize time from NTP server (one-shot update) [Syntax] ntpdate oneshot [Input mode] priviledged EXEC mode [Description] Attempts - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 43
time : Thu Jan 1 09:00:00 2015 + interval 1 hour sync server : ntp.nict.jp Show time synchronization settings. *If periodic synchronization is not being performed SWR2311P#show ntpdate NTP Server 1 : ntp.nict.jp NTP Server 2 : none adjust time : Thu Jan 1 09:00:00 2015 sync server : ntp.nict.jp - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 44
command. To return to priviledged EXEC mode, use the end command. [Example] Move to line mode in order to make console terminal settings. SWR2311P(config)#line con 0 SWR2311P(config-line)# 4.7.2 Set VTY port and move to line mode (VTY port) [Syntax] line vty port1 [port2] no line vty port1 [port2 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 45
of executing this command takes priority over the setting applied by the service terminal-length command. [Example] Change the number of lines displayed per page for the terminal in use to 100 lines. SWR2311P>terminal length 100 SWR2311P> 4.7.5 Set the number of lines displayed per page on the - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 46
] Change the number of lines displayed per page for the terminal in use to 100 lines. SWR2311P(config)#service terminal-length 100 SWR2311P(config)# 4.8 Management 4.8.1 Set management VLAN [Syntax] management interface interface no management interface [Parameter] interface : VLAN interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 47
Set the SYSLOG server IPv6 address to fe80::2a0:deff:fe11:2233. SWR2311P(config)#logging host fe80::2a0:deff:fe11:2233%vlan1 4.9.2 Set log output is not output. [Example] Output the debug level log to SYSLOG. SWR2311P(config)#logging trap debug 4.9.3 Set log output level (informational) [Syntax] - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 48
to SYSLOG. If this command is executed with the "no" syntax, the log is not output. [Example] Output the error level log to SYSLOG. SWR2311P(config)#logging trap error 4.9.5 Set log console output [Syntax] logging stdout info no logging stdout info [Initial value] no logging stdout info [Input mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 49
syntax, the log is not output. [Example] Enable log output for LAN map. SWR2311P(config)#logging event lan-map 4.9.7 Back up log [Syntax] save logging [Input mode] Flash ROM, but you can use this command to back up this data manually. If the logging backup sd enable command has been set and an SD - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 50
that are not backed up will not be saved, so you must back them up manually if you want to save the log. The log is maintained when the reload command a firmware update etc. cause a reboot. [Example] Show the log. SWR2311P#show logging 4.10 SNMP 4.10.1 Set host that receives SNMP notifications [ - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 51
%vlan2" will remain. [Example] Using SNMPv1, set 192.168.100.11 as the destination for traps. Set "snmptrapname" as the trap community name. SWR2311P(config)#snmp-server host 192.168.100.11 traps version 1 snmptrapname Using SNMPv2c, set 192.168.100.12 as the destination for notifications. Specify - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 52
for notifications. Set the notification type to traps, set the security level for transmission to priv, and set the user name to "admin1". SWR2311P(config)#snmp-server host 192.168.10.13 traps version 3 priv admin1 4.10.2 Set notification type to transmit [Syntax] snmp-server enable trap - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 53
this command is executed with the "no" syntax, the setting is deleted. [Example] Set the system contact to "[email protected]". SWR2311P(config)#snmp-server contact [email protected] 4.10.4 Set system location [Syntax] snmp-server location location no snmp-server location [Parameter - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 54
"no" syntax, the specified community is deleted. [Example] Set the read-only community name to "public". SWR2311P(config)#snmp-server community public ro Delete the "public" community. SWR2311P(config)#no snmp-server community public 4.10.6 Set SNMP view [Syntax] snmp-server view view oid type no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 55
setting is deleted. [Example] Create the user group "admins," and grant users belonging to the "admins" group full access rights to the "most" view. SWR2311P(config)#snmp-server group admins priv read most write most Create the user group "users," and grant users belonging to the "users" group read - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 56
and the security level prescribed for that group, specify the protocol (SHA, AES) and password (passwd1234) used for authentication and encryption. SWR2311P(config)#snmp-server user admin1 admins auth sha passwd1234 priv aes passwd1234 Create "user1" as a user. According to the specified group and - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 57
the contents of the SNMP view settings. Shows the view name, object ID, and type. [Example] Show the contents of the SNMP view settings. SWR2311P#show snmp view SNMP View information View Name: most OID: 1.6.1 Type: include View Name: standard OID: 1.3.6.1.2.1 Type: include 4.10.11 Show SNMP group - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 58
[Example] Show the contents of the SNMP user settings. SWR2311P#show snmp user SNMP User information EngineID: 0x8000049e0300a0deaeb90e User Name Set RMON function [Syntax] rmon swtich no rmon [Parameter] switch : RMON function operation enable disable Setting value Description Enable RMON - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 59
, and collection is once again started. [Example] Enable the RMON Ethernet statistical information group settings for port1.1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#rmon statistics 1 4.11.3 Set RMON history group [Syntax] rmon history index [buckets buckets] [interval interval - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 60
data is deleted, and collection is once again started. [Example] Enable the RMON historical group settings for port1.1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#rmon history 1 4.11.4 Set RMON event group [Syntax] rmon event index type community [description description] [owner - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 61
the type of event as "log-trap", and the community name of the trap as "public". SWR2311P(config)#snmp-server host 192.168.100.3 traps version 2c public SWR2311P(config)#snmp-server enable trap rmon SWR2311P(config)#rmon event 1 log-trap public 4.11.5 Set RMON alarm group [Syntax] rmon alarm index - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 62
62 | Command Reference | Maintenance and operation functions absolute delta Setting value Description Compare by absolute value. Directly compare sample value and threshold value Compare by relative value. Compare the difference between the latest sample value and the previous sample value - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 63
upper threshold value is 1. • The lower threshold value is 2000, and the event when falling below the lower threshold value is 1. SWR2311P(config)#rmon alarm 1 etherStatsPkts.1 interval 180 delta rising-threshold 3000 event 1 falling-threshold 2000 event 1 4.11.6 Show RMON function status [Syntax - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 64
the RMON Ethernet statistical information group. The following items are shown. • Index • Applicable interface • Input packets • Output packets [Example] SWR2311P>show rmon statistics rmon collection index 1 stats->ifindex = 5001 input packets 7, bytes 600, drop events 0, multicast packets 4 output - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 65
items are shown. • Index • Description of event • Type of event • Community name when sending trap • Time of executing event • Owner name [Example] SWR2311P>show rmon event event Index = 1 Description RMON_SNMP Event type Log Event community name RMON_SNMP Last Time Sent = 00:00:58 Owner RMON_SNMP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 66
group for the applicable interface. [Example] Clear the counters of the RMON Ethernet statistical information group for port1.1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#rmon clear counters 4.12 Telnet server 4.12.1 Start Telnet server and change listening port number [Syntax - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 67
to access the TELNET server • Filter that controls access to the TELNET server [Example] Show the settings of the Telnet server. SWR2311P#show telnet-server Service:Enable Port:23 Management interface(vlan): 1 Interface(vlan):1, 2, 3 Access: deny 192.168.100.5 permit 192.168.100.0/24 4.12.3 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 68
does not function. [Example] Permit access to the TELNET server only from 192.168.1.1 and the 192.168.10.0/24 segment. SWR2311P(config)#telnet-server access permit 192.168.1.1 SWR2311P(config)#telnet-server access permit 192.168.10.0/24 Deny only access to the TELNET server from the segment 192.168 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 69
number 12345 of the host at IPv6 address fe80::2a0:deff:fe11:2233. SWR2311P#telnet fe80::2a0:deff:fe11:2233%vlan1 12345 4.13.2 Enable Telnet client [Syntax] telnet-client switch no telnet-client [Parameter] switch : Whether to enable TELNET client enable disable Setting value Enable Disable - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 70
port number • VLAN interface that is permitted to access the TFTP server [Example] Show the settings of the TFTP server. SWR2311P#show tftp-server Service:Enable Port:69 Management interface(vlan): 1 Interface(vlan):1, 2, 3 4.14.3 Set hosts that can access the TFTP server [Syntax] tftp-server - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 71
command is executed with the "no" syntax, the function is disabled. [Example] Start the HTTP server with 8080 as the listening port number. SWR2311P(config)#http-server enable 8080 4.15.2 Start secure HTTP server and change listening port number [Syntax] http-server secure enable [port] http-server - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 72
to the HTTP server • Secure HTTP server function enabled/disabled status • Log-in timeout time [Example] Show the settings of the HTTP server. SWR2311P#show http-server HTTP :Enable(80) HTTPS:Disable Management interface(vlan): 1 Interface(vlan):1 Access:None Login timeout:30 min 51 sec 4.15.4 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 73
does not function. [Example] Permit access to the HTTP server only from 192.168.1.1 and the 192.168.10.0/24 segment. SWR2311P(config)#http-server access permit 192.168.1.1 SWR2311P(config)#http-server access permit 192.168.10.0/24 Deny access to the HTTP server only from 192.168.10.0/24 segment - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 74
to the default. [Example] Set the Web GUI display language to English. SWR2311P(config)#http-server language english 4.15.7 Set log-in timeout time for HTTP the HTTP server to 2 minutes 30 seconds. SWR2311P(config)#http-server login-timeout 2 30 4.16 HTTP Proxy 4.16.1 Enable HTTP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 75
, the function is disabled. [Example] Enable the HTTP Proxy function of the HTTP server. SWR2311P(config)#http-proxy enable 4.16.2 Set HTTP Proxy function timeout [Syntax] http-proxy timeout time ] Show the settings of the HTTP Proxy function. SWR2311P#show http-proxy Service:Enable Timeout:60 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 76
the SSH server with 12345 as the listening port number. SWR2311P#ssh-server host key generate SWR2311P#configure terminal SWR2311P(config)#ssh-server enable 12345 4.17.2 Show SSH server [Example] Show the settings of the SSH server. SWR2311P#show ssh-server Service:Enable Port:23 Hostkey:Generated - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 77
only from the maintenance VLAN. [Example] Allow access to the SSH server from the hosts connected to VLAN #1 and VLAN #2. SWR2311P(config)#ssh-server interface vlan1 SWR2311P(config)#ssh-server interface vlan2 4.17.4 Set client that can access the SSH server [Syntax] ssh-server access action info - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 78
generate the host keys. This command can be executed only if the SSH server is disabled. [Example] Generate a 2048-bit RSA key and a DSA key. SWR2311P#ssh-server host key generate bit 2048 4.17.6 Clear SSH server host key [Syntax] clear ssh-server host key [Input mode] priviledged EXEC mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 79
server. [Note] This command can be executed only if the SSH server is disabled. [Example] Delete the host RSA key and host DSA key. SWR2311P#clear ssh-server host key 4.17.7 Show SSH server public key [Syntax] show ssh-server host key [fingerprint] [Keyword] fingerprint : Show key fingerprint - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 80
80 | Command Reference | Maintenance and operation functions | oXS | | +=*. | | o.B*. | | + o . | | * * + | |X+.@ +o= | |@*o.= o. | +----[SHA256]-----+ ssh-rsa 2048 MD5:XX:XX:b8:07:e3:5e:57:b8:80:e3:fc:b3:24:17:XX:XX +---[RSA 2048]----+ | | |...* | |*+. | | . | | . + | - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 81
, connect via SSH using user name "uname" and port number 12345. SWR2311P#ssh uname@fe80::2a0:deff:fe11:2233%vlan1 12345 4.18.2 Enable SSH client [Syntax] ssh-client switch no ssh-client [Parameter] switch : Whether to enable SSH client Setting value enable disable Description Enable Disable - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 82
EXEC mode [Description] Delete the public key of the SSH server that is connected as an SSH client. [Example] Clear the SSH host information. SWR2311P#clear ssh host 192.168.100.1 4.19 LLDP 4.19.1 Enable LLDP function [Syntax] lldp run no lldp run [Initial value] none [Input mode] global - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 83
. By default, this is "model name". The specified value is set in "LLDP System Name TLV". [Example] Set the system name to SWITCH1. SWR2311P(config)#lldp system-name SWITCH1 4.19.4 Create LLDP agent [Syntax] lldp-agent no lldp-agent [Initial value] none [Input mode] interface mode [Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 84
by which LLDP frames transmitted by specific Yamaha devices can automatically modify the settings of a switch. The functions that can be set are of LLDP frames. [Example] Enable automatic setting function by LLDP. SWR2311P(config)#lldp auto-setting enable 4.19.6 Set LLDP transmission/reception mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 85
to the default. [Example] Set the LLDP transmission/reception mode of LAN port #1 to receive-only. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#set lldp enable rxonly 4.19.7 Set type of management address [Syntax] set management - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 86
VLAN ID : ID of protocool VLAN (3) Protocol Identity : List of supported protocols (4) Link Aggregation : Link aggregation information (5) VLAN Name : Name on LAN port #1. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#tlv-select - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 87
of "Location". [Example] Add LLDP-MED TLVs to the LLDP frames that are transmitted on LAN port #1. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#tlv-select med 4.19.12 Set LLDP frame transmission interval [Syntax] set timer msg-tx - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 88
2 seconds as the LLDP frame transmission interval during the high speed transmission period on LAN port #1. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#set timer msg-fast-tx 2 4.19.14 Set time from LLDP frame transmission stop - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 89
2 as the multiplier used to calculate the time to live (TTL) for device information on LAN port #1. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#set msg-tx-hold 2 4.19.16 Set number of LLDP frames transmitted during the high speed - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 90
Set 10 as the maximum number of connected devices that can be managed by a port on LAN port #1. SWR2311P(config)#lldp run SWR2311P(config)#interface port1.1 SWR2311P(config-if)#lldp-agent SWR2311P(lldp-agent)#set too-many-neighbors limit 10 4.19.18 Show interface status [Syntax] show lldp interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 91
to maintain device information (seconds) ID of port VLAN ID of protocol VLAN ID of port VLAN Name of port VLAN List of supported protocols VID Usage Digestt value Name of management VLAN Link aggregation enabled/disabled ID of link aggregation port Auto negotiation enabled/disabled Communication - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 92
id ID of VLAN MED Tag/Untag VLAN tagged or untagged MED L2 Priority L2 priority order MED DSCP Val DSCP value priority order MED Location on location information. [Example] Show LLDP information for LAN port #1. SWR2311P#show lldp interface port1.1 Agent Mode : Nearest bridge Enable (tx/ - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 93
SWR2311P-10G System Description : SWR2311P Rev.2.02.06 (Tue Mar 13 08:41:39 2018) Port Description : port1.3 System Capabilities : L2 Switching Aggregation Port ID : 0 8023 ORIGIN SPECIFIC TLVs AutoNego Support : Supported Enabled AutoNego Capability : 27649 Operational MAU Type : 30 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 94
EXEC mode [Description] Clear the LLDP frame counter of all ports. [Example] Clear the LLDP frame counter. SWR2311P>clear lldp counters 4.20 L2MS (Layer 2 management service) settings 4.20.1 Move to L2MS mode [Syntax] l2ms configuration [Input mode] global configuration mode [Description] Moves to - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 95
subordinate to it Be managed from a Yamaha device that is operating as an L2MS master, such as an SWR2311P-10G unit that is set as the L2MS slave. [Note] If the same network includes multiple Yamaha routers or firewalls on which L2MS (switch controller function) is enabled, or multiple SWR series - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 96
only if L2MS is operating as master. [Example] Set the watch interval to five seconds. SWR2311P(config)#l2ms configuration SWR2311P(config-l2ms)#l2ms enable SWR2311P(config-l2ms)#l2ms role master SWR2311P(config-l2ms)#slave-watch interval 5 4.20.5 Set number of times that is interpreted as L2MS - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 97
this command. [Example] Set the watch interval to 3,600 seconds. SWR2311P(config)#l2ms configuration SWR2311P(config-l2ms)#l2ms enable SWR2311P(config-l2ms)#l2ms role master SWR2311P(config-l2ms)#terminal-watch enable SWR2311P(config-l2ms)#terminal-watch interval 3600 4.20.8 Set L2MS control frame - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 98
been specified • It is inside a logical interface [Example] Prevent port1.5 from transmitting or receiving L2MS control frames. SWR2311P(config)#interface port1.5 SWR2311P(config-if)#l2ms filter enable 4.20.9 Reset slave management [Syntax] l2ms reset [Input mode] priviledged EXEC mode [Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 99
Information of terminals connected to the L2MS slave (in the case of a switch) • MAC address • Ports connected • Time at which terminal was discovered [Example] If L2Ms is operating as master, show detailed L2MS information. SWR2311P>show l2ms detail Role : Master [Master] Number of Terminals : 0 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 100
of Terminals : 1 [bcae.c5a4.7fb3] Port : 9 Appear time : Wed Mar 14 14:01:18 2018 [00a0.deae.b8bf] Model name : SWR2311P-10G Device name : SWR2311P-10G_S4L000401 Route : port2.1-3 LinkUp : 1 Uplink : 1 Downlink : None Config : None Appear time : Tue Mar 13 18:43:18 2018 Number - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 101
of the setting of this command. [Example] Set the monitoring time interval to 60 seconds. SWR2311P(config)#l2ms configuration SWR2311P(config-l2ms)#l2ms enable SWR2311P(config-l2ms)#l2ms role master SWR2311P(config-l2ms)#event-watch interval 60 4.20.14 Set whether to use the L2MS slave's zero - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 102
is enabled, and the L2MS slave's Yamaha switch or wireless AP settings (config) are saved SWR2311P-10G is performed regardless of this setting. [Example] Use the L2MS function. SWR2311P(config)#l2ms configuration SWR2311P(config-l2ms)#l2ms enable SWR2311P(config-l2ms)#l2ms role master SWR2311P - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 103
, it might take some time for this update to be completed. [Example] After updating the network's connection state, save the snapshot file. SWR2311P#snapshot save after-update 4.21.4 Delete snapshot [Syntax] snapshot delete [Input mode] priviledged EXEC mode [Description] Deletes the snapshot file - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 104
(255 characters or less) URL at which the firmware is located [Initial value] firmware-update url http://www.rtpro.yamaha.co.jp/firmware/revision-up/swr2311p.bin [Input mode] global configuration mode [Description] Specify the download source URL used when updating the firmware from a firmware - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 105
. • Download source URL • Download timeout duration • Allow revision-down [Example] Show the current settings of the firmware update function. SWR2311P#show firmware-update url: http://www.rtpro.yamaha.co.jp/firmware/revision-up/swr2311p.bin timeout: 300 (seconds) revision-down: Disable reload-time - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 106
for confirmation. If you specify sd-unmount, the SD card is unmounted without asking for confirmation. [Note] The firmware file references the "\swr2311p\firmware\swr2311p.bin" file on the SD card. A revision check is not performed for the firmware file in the SD card and the currently-running - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 107
is executed with the "no" syntax, the setting returns to the default value. [Example] Set the host name as "yamaha." SWR2311P(config)#hostname yamaha yamaha(config)# 4.23.2 Reload system [Syntax] reload [Input mode] priviledged EXEC mode [Description] Reboots the system. [Note] If the currently - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 108
need to execute this. [Note] The SD card cannot be used if the SD card is in an unmounted state. [Example] Mount the SD card. SWR2311P>mount sd 4.23.5 Unmount SD card [Syntax] unmount sd [Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description] Unmounts the SD card. If this command - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 109
If this command is executed with the "no" syntax, the setting returns to the default. [Example] Set the default LED mode to OFF mode. SWR2311P(config)#led-mode default off 4.23.7 Show LED mode [Syntax] show led-mode [Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description] Shows the - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 110
mounted. [Note] Do not edit or delete the files that are backed up to the SD card. [Example] Execute a system information backup. SWR2311P#backup system Succeeded to backup system files and firmware file. 4.23.10 Restore system information [Syntax] restore system [Input mode] priviledged EXEC mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 111
Command Reference | Maintenance and operation functions | 111 Update to this firmware? (Y/N) Y Unmounted the SD card. Pull out the SD card. Updating... Finish Succeeded to restore system files. SWR2311P# - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 112
command is executed with the "no" syntax, the description is deleted. [Example] Specify a description for LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#description Connected to rtx1210-router 5.1.2 Shutdown [Syntax] shutdown no shutdown [Initial value] no shutdown [Input mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 113
be specified for combo port is auto or 1000-full. [Example] Set the speed and duplex mode for LAN port #1 to 100Mbps/Full. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#speed-duplex 100-full 5.1.4 Set MRU [Syntax] mru mru no mru [Parameter] mru : Maximum frame size that can be - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 114
settings, link-down temporarily occurs for the corresponding interface. [Example] Disable cross/straight automatic detection for LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#mdix auto disable 5.1.6 Set EEE [Syntax] eee action no eee [Parameter] type : Behavior of the EEE - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 115
:port1.1 EEE(efficient-ethernet): yes (1000-T, 100-TX) Link Partner : yes (1000-T, 100-TX) [If the other unit does not support EEE] SWR2311P#show eee capabilities interface port1.1 interface:port1.1 EEE(efficient-ethernet): yes (1000-T, 100-TX) Link Partner : not enabled 5.1.8 Show EEE - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 116
receiving unit Low-power mode status of the transmitting unit Error count [Example] Show EEE status of LAN port #1. [If EEE is disabled] SWR2311P#show eee status interface port1.1 interface:port1.1 EEE(efficient-ethernet): Disabled Rx LPI Status : None Tx LPI Status : None Wake Error Count - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 117
transmitted and received frames of LAN port #4 and the transmitted frames of LAN port #5. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#mirror interface port1.4 direction both SWR2311P(config-if)#mirror interface port1.5 direction transmit 5.1.10 Show port mirroring status [Syntax] show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 118
interface LACP logical interface Description Specifies the stack ID (S) of the physical interface, and the number printed on the chassis (X). * The SWR2311P-10G is fixed as stack ID=1. Specify the VLAN ID. Speciffy the static logical interface number. Specify the LACP logical interface number - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 119
transmission information when tail dropping is enabled, and the information only for reception when tail dropping is disabled. [Example] Show the status of LAN port #1. SWR2311P# show interface port 1.1 Interface port1.1 Link is UP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 120
packets: 301 output packets : 628 bytes : 129895 multicast packets: 628 broadcast packets: 0 drop packets : 0 Show the status of VLAN #1. SWR2311P#show interface vlan 1 Interface vlan1 Hardware is VLAN Description: Connected to router(VLAN) ifIndex 301, ARP ageing timeout 1200 IPv4 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 121
of interface *1 Shown only for physical interface *2 hown only for physical interface and logical interface [Example] Show brief interface status. SWR2311P#show interface brief Codes: ETH - Ethernet, AGG - Aggregate , PVID - Port Vlan-id ED - ErrDisabled, PD - Protocol Down, AD - Admin Down - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 122
enabled, and the information only for reception when tail dropping is disabled. [Example] Show the frame counter of LAN port #1. SWR2311P#show frame-counter port1.1 Interface port1.1 Ethernet MAC counters: Received: Packets : 84 Octets : 6721 Broadcast packets : 8 Multicast packets : 76 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 123
frame counters of all LAN/SFP port port units associated with that interface are cleared. [Example] Clear the frame counters of LAN port #1. SWR2311P#clear counters port1.1 5.1.15 Show SFP module status [Syntax] show ddm status [Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 124
mode [Description] Sets the monitoring of SFP module optical reception levels. [Example] Disable SFP module optical reception level monitoring. SWR2311P(config)#sfp-monitor rx-power disable 5.2 Link aggregation 5.2.1 Set static logical interface [Syntax] static-channel-group link-id no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 125
balance function rules, refer to the type parameter of the port-channel load-balance command. [Example] Show the static logical interface status. SWR2311P#show static-channel-group % Static Aggregator: sa5 % Load balancing: src-dst-mac % Member: port1.1 port1.2 port1.3 port1.4 5.2.3 Set LACP logical - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 126
it with a different logical interface. [Example] Associate LAN port #1 in ACTIVE mode with LACP logical interface #10. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#channel-group 10 mode active 5.2.4 Show LACP logical interface status [Syntax] show etherchannel [ifname] [Parameter - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 127
Interfaces that make up the LACP logical interface Command Reference | Interface control | 127 [Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description] If ifname is omitted, shows the status of the LACP logical interface. The following items are shown for each LACP logical - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 128
% Member: port1.1 port1.2 port1.3 port1.4 Shows the status of the LAN/SFP ports that make up the LACP logical interface. SWR2311P#show etherchannel port1.1 Etherchannel port1.1 Physical admin key 3 Receive machine state Current Periodic Transmission machine state Slow periodic Mux machine - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 129
can be set by the lacp system-priority command. The LACP system ID is generated from the MAC address. [Example] Show the LACP system priority. SWR2311P>show lacp sys-id % System 0x8000, 00-a0-de-e0-e0-e0 5.2.7 Set LACP timeout [Syntax] lacp timeout duration [Parameter] duration : Specify the - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 130
the frame counter of every existing LACP logical interface is cleared. [Example] Clear the frame counter for every LACP logical interface. SWR2311P#clear lacp counters 5.2.9 Show LACP frame counter [Syntax] show lacp-counter [link-id] [Parameter] link-id : LACP logical interface number - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 131
load balance function, set the system to determine the forwarding destination interface based on the transmissionsource and destination IPv4/IPv6 address. SWR2311P(config)#port-channel load-balance src-dst-ip 5.2.11 Show protocol status of LACP logical interface [Syntax] show etherchannel status - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 132
. Selected yes Selected as a LAN/SFP port with LACP enabled. Combined as link aggregation, [Example] Show the status of the LACP logical interface. SWR2311P#show etherchannel status summary Aggregator po1 ID 4601 Status Ready Partner LAG 0x8000, 00-a0-de-11-11-11 Partner Key 0001 Link - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 133
ID 4727 Status Not ready Partner LAG 0x8000, 00-a0-de-11-11-11 Partner Key 0001 Link count 0/ 1 Command Reference | Interface control | 133 SWR2311P#show etherchannel status detail Aggregator po1 ID 4601 Status Ready Actor LAG 0x8000, 00-a0-de-e0-e0-e0 Admin Key 0001 Partner LAG - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 134
port priority must be set lower than other ports. [Example] Set the LACP port priority order to 1024. SWR2311P(config-if)#channel-group 1 mode active SWR2311P(config-if)#lacp port-priority 1024 5.3 Port authentication 5.3.1 Configuring the IEEE 802.1X authentication function for the entire system - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 135
only for both LAN/SFP port and logical interface. [Example] This command can be specified only for LAN/SFP port. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#dot1x port-control auto 5.3.5 Set for forwarding control on an unauthenticated port for IEEE 802.1X authentication [Syntax] dot1x - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 136
command) [Example] Discard received packets only for the packet forwarding operation on an unauthenticated port of LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#dot1x control-direction in 5.3.6 Set the EAPOL packet transmission count [Syntax] dot1x max-auth-req count no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 137
for the entire system as well. (aaa authentication auth-mac command) [Example] Enable the LAN port #1 MAC authentication function. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth-mac enable 5.3.8 Set MAC address format during MAC authentication [Syntax] auth-mac auth-user type case no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 138
besides multi-supplicant mode. You cannot use this together with guest VLAN. [Example] Enable the LAN port #1 Web authentication function. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth-web enable 5.3.10 Set host mode [Syntax] auth host-mode mode no auth host-mode [Parameter] mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 139
command, auth-mac enable command, auth-web enable command) [Example] Change the LAN port #1 to multi supplicant mode. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth host-mode multi-supplicant 5.3.11 Set re-authentication [Syntax] auth reauthentication no auth reauthentication [Initial - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 140
interface. (dot1x port-control command, auth-mac enable command, auth-web enable command) [Example] Enable dynamic VLAN on LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth dynamic-vlan-creation 5.3.13 Set the guest VLAN [Syntax] auth guest-vlan vlan-id no auth guest-vlan - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 141
command, auth-mac enable command, auth-web enable command) [Example] Set the suppression period for LAN port #1 to 300. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth timeout quiet-period 300 5.3.15 Set reauthentication interval [Syntax] auth timeout reauth-period time no auth - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 142
] This sets the reply wait time to the RADIUS server overall to 180 seconds, for authentication requests from LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth timeout server-timeout 180 5.3.17 Set supplicant reply wait time [Syntax] auth timeout supp-timeout time no auth - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 143
192.168.100.100, with a reply standby time of 10 seconds and a number of times to resend requests of 5 seconds to the authentication server list. SWR2311P(config)#radius-server host 192.168.100.100 timeout 10 retransmit 5 Add the server at IP address 192.168.100.101, with an authentication UDP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 144
within the number set in the auth timeout server-timeout command. [Example] Set the reply wait time for each RADIUS server to 10 seconds. SWR2311P(config)#radius-server timeout 10 5.3.20 Set number of times to resend requests to RADIUS server [Syntax] radius-server retransmit count no radius-server - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 145
-server host command, the radius-server host command settings are used. [Example] The shared password used with the RADIUS server is "abcde". SWR2311P(config)#radius-server key abcde 5.3.22 Set time of RADIUS server usage prevention [Syntax] radius-server deadtime time no radius-server deadtime - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 146
146 | Command Reference | Interface control 802.1X Port-Based Authentication : Enabled MAC-Based Authentication : Disabled WEB-Based Authentication : Enabled Clear-state time : Not configured Redirect URL : Not configured Auth-web custom-file : There is no custom-file RADIUS server address - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 147
EXEC mode [Description] Shows statistical information for packets during port authentication. [Example] Show statistical information for LAN port #1. SWR2311P#show auth statistics interface port1.1 Interface port1.1 EAPOL frames: Received frames : 11 EAPOL Start : 1 EAPOL Logoff : 0 EAP - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 148
usage prevention time) for RADIUS servers registered in the authentication server list. [Example] Show setting information related to the RADIUS server. SWR2311P#show radius-server Server Host : 192.168.100.101 Authentication Port : 1812 Secret Key : abcde Timeout : 10 sec Retransmit Count - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 149
the interface. [Example] This sets the time at which the authentication state for the supplicant is cleared for the entire system to 12:00. SWR2311P(config)#auth clear-state time 12 5.3.31 Setting the time for clearing the authentication state (interface) [Syntax] auth clear-state time time no auth - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 150
to LAN port #1 is cleared to 12:00. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#auth clear-state time 12 5.3.32 Locate the the file for customizing the Web authentication screen from an SD card to the switch, put the respective files in the /[model name]/startup-config/web-auth/ folder - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 151
an error. [Example] Deletes logo.png from startup configuration #0. SWR2311P#erase auth-web startup-config logo.png 0 5.3.34 Set EAP pass through [Syntax] pass-through eap switch no pass-through eap [Parameter] switch : Behavior EAP pass through enable disable Setting value Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 152
be discarded at the time when the port security function is enabled. [Example] Enable port security for LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#port-security enable 5.4.2 Register permitted MAC addresses [Syntax] port-security mac-address no port-security mac-address - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 153
-security status [Input mode] priviledged EXEC mode [Description] Shows the port security information. [Example] Show the port security information. SWR2311P#show port-security status Port Security Action Status Last violation port1.1 Enabled Discard Blocking 00a0.de00.0003 port1.2 Disabled - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 154
next time BPDU is detected. [Example] Enable automatic recovery after BPDU guard has caused the errdisable state, and set the recovery time to 600 seconds. SWR2311P(config)#errdisable auto-recovery bpduguard interval 600 Disable automatic recovery after loop detection has caused the errdisable state - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 155
(config)#power-inline enable Disable the system-wide PoE power supply function. SWR2311P(config)#power-inline disable 5.6.2 Set PoE power supply function (interface) [Syntax] power-inline switch no power-inline [Parameter] switch : PoE power supply function settings for the applicable interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 156
[Example] Enable the PoE power supply function for port1.1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#power-inline enable Disables the PoE power supply function for port1.1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#power-inline disable 5.6.3 Set description of PoE port - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 157
priority is shown using the show power-inline command. [Example] Set the power supply priority for port1.5 to high. SWR2311P(config)#interface port1.5 SWR2311P(config-if)#power-inline priority high 5.6.5 Show PoE power supply information [Syntax] show power-inline show power-inline interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 158
, a dynamic entry is not registered in the MAC address table even if a frame is received. [Example] Enable the MAC address acquisition function. SWR2311P(config)#mac-address-table learning enable 6.1.2 Set dynamic entry ageing time [Syntax] mac-address-table ageing-time time no mac-address-table - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 159
deleted. If no keyword is specified, all dynamic entries are deleted. [Example] Delete the dynamic entry whose MAC address is 00a0.de11.2233. SWR2311P#clear mac-address-table dynamic address 00a0.de11.2233 6.1.4 Set static entry [Syntax] mac-address-table static mac-addr action ifname [vlan vlan - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 160
.c200.0020 - 0180.c200.002f • ffff.ffff.ffff [Example] Specify that frames addressed to 00a0.de11.2233 are forwarded to LAN port #2. SWR2311P(config)#mac-address-table static 00a0.de11.2233 forward port1.2 6.1.5 Show MAC address table [Syntax] show mac-address-table [Input mode] unprivileged EXEC - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 161
configuration mode, use the exit command. To return to priviledged EXEC mode, use the end command. [Example] Move to VLAN mode. SWR2311P(config)#vlan database SWR2311P(config-vlan)# 6.2.2 Set VLAN interface [Syntax] vlan vlan-id [name name] [state state] no vlan vlan-id [Keyword] name : Specifies - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 162
as shown below • To select from VLAN #2 through VLAN #4: 2-4 • To select VLAN #2 and VLAN #4: 2,4 [Example] Set VLAN #1000 with the name "Sales". SWR2311P(config-vlan)#vlan 1000 name Sales 6.2.3 Set private VLAN [Syntax] private-vlan vlan-id type no private-vlan vlan-id type [Parameter] vlan-id - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 163
#103 : Secondary VLAN (isolated VLAN) SWR2311P(config-vlan)#vlan 100 SWR2311P(config-vlan)#vlan 101 SWR2311P(config-vlan)#vlan 102 SWR2311P(config-vlan)#vlan 103 SWR2311P(config-vlan)#private-vlan 100 primary SWR2311P(config-vlan)#private-vlan 101 community SWR2311P(config-vlan)#private-vlan 102 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 164
is associated as an access port, use the switchport access vlan command. [Example] Set LAN port #1 as an access port. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport mode access 6.2.6 Set associated VLAN of an access port (untagged port) [Syntax] switchport access vlan vlan-id no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 165
. To specify the native VLAN, use the switchport trunk native vlan command. [Example] Set LAN port #1 as a trunk port. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport mode trunk 6.2.8 Set associated VLAN for trunk port (tagged port) [Syntax] switchport trunk allowed vlan all - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 166
add 101,103-105) [Example] Set LAN port #1 as the trunk port, and associate it to VLAN #2. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport mode trunk SWR2311P(config-if)#switchport trunk allowed vlan add 2 6.2.9 Set native VLAN for trunk port (tagged port) [Syntax] switchport - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 167
is specified. [Example] Set LAN port #1 as the trunk port, and specify VLAN #2 as the native VLAN. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport mode trunk SWR2311P(config-if)#switchport trunk native vlan 2 6.2.10 Set private VLAN port type [Syntax] switchport mode private-vlan - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 168
: Primary VLAN #100, Secondary VLAN #103 SWR2311P(config)# interface port1.1 SWR2311P(config-if)# switchport mode private-vlan host SWR2311P(config-if)# switchport private-vlan host-association 100 add 101 SWR2311P(config-if)# interface port1.2 SWR2311P(config-if)# switchport mode private-vlan host - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 169
VLAN #100, and associate the secondary VLANs #101, #102, and #103. SWR2311P(config)# interface port1.1 SWR2311P(config-if)# switchport mode private-vlan promiscuous SWR2311P(config-if)# switchport private-vlan mapping 100 add 101 SWR2311P(config-if)# switchport private-vlan mapping 100 add 102 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 170
reception is possible for the corresponding port. [Example] Set the CoS value to 6 for using LAN port #1 as voice VLAN. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport voice cos 6 6.2.15 Set DSCP value for voice VLAN [Syntax] switchport voice dscp value no switchport voice dscp - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 171
MLD snooping status • Loop detection block status [Example] Assign LAN port #1 to multiple VLAN group #10. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#switchport multiple-vlan group 10 SWR2311P(config-if)#exit 6.2.17 Set name of multiple VLAN group [Syntax] multiple-vlan group group-id - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 172
The name that was set is shown with the show vlan multiple-vlan command. [Example] Set multiple VLAN group #10 with the name "Network1". SWR2311P(config)#multiple-vlan group 10 name Network1 6.2.18 Show VLAN information [Syntax] show vlan vlan-id show vlan brief [Keyword] brief : Show all VLAN - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 173
omitted, all groups that are actually assigned to the interface are shown. [Example] Shows the setting status for multiple VLAN groups. SWR2311P>show vlan multiple-vlan GROUP ID Name Member ports 1 GROUP0001 port1.1 port1.2 port1.5 6.3 STP (Spanning Tree Protocol) 6.3.1 Set spanning tree - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 174
be changed. [Example] Set the forward delay time to 10 seconds. SWR2311P(config)#spanning-tree forward-time 10 6.3.3 Set maximum aging time [Syntax] . [Note] The maximum aging time is the time that the L2 switch waits without receiving a spanning tree configuration message, and after which time - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 175
for CIST (instance #0). [Example] Set the bridge priority to 4096. SWR2311P(config)#spanning-tree priority 4096 6.3.5 Set spanning tree for an interface [Syntax] spanning-tree switch [Parameter] switch : Spanning tree operation Setting value enable disable Description Enable spanning tree - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 176
for the corresponding LAN/SFP port returns to the default. [Example] Set the LAN port #1 link type to "shared." SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree link-type shared 6.3.7 Set interface BPDU filtering [Syntax] spanning-tree bpdu-filter filter no spanning-tree bpdu - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 177
of this command for the corresponding LAN/SFP port returns to the default. [Example] Enable BPDU filtering for LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree bpdu-filter enable 6.3.8 Set interface BPDU guard [Syntax] spanning-tree bpdu-guard guard no spanning-tree - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 178
for the corresponding LAN/SFP port returns to the default. [Example] Set the path cost of LAN port #1 to 100000. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree path-cost 100000 6.3.10 Set interface priority [Syntax] spanning-tree priority priority no spanning-tree priority - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 179
of this command for the corresponding LAN/SFP port returns to the default. [Example] Set LAN port #1 as the edge port. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree edgeport 6.3.12 Show spanning tree status [Syntax] show spanning-tree [interface ifname] [Keyword] interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 180
180 | Command Reference | Layer 2 functions Item Max Age Root Id Bridge Id topology change(s) last topology change Ifindex Port Id Role State Designated Path Cost Configured Path Cost Add type Explicit ref count Designated Port Id Priority Root Designated Bridge Message Age Hello Time Forward Delay - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 181
type. Either point-to-point or shared Auto-edge setting and current status [Example] Show the spanning tree status for LAN port #1. SWR2311P>show spanning-tree interface port1.1 % Default: Bridge up - Spanning Tree Enabled - topology change detected % Default: CIST Root Path Cost 0 - CIST Root - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 182
182 | Command Reference | Layer 2 functions % Spanning Tree Type % Current Port State % Port ID % Port Number % Path Cost % Message Age % Designated Root % Designated Cost % Designated Bridge % Designated Port Id % Top Change Ack % Config Pending : Multiple Spanning Tree Protocol : Forwarding : - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 183
the interface return from STP compatibility mode to normal mode. [Example] Return LAN port #1 from STP compatibility to normal mode. SWR2311P#clear spanning-tree detected protocols interface port1.1 6.3.15 Move to MST mode [Syntax] spanning-tree mst configuration [Input mode] global configuration - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 184
cannot specify a VLAN ID that is associated with another MST instance. [Example] Associate VLAN #2 with MST instance #1. SWR2311P(config)#spanning-tree mst configuration SWR2311P(config-mst)#instance 1 vlan 2 6.3.18 Set priority of MST instance [Syntax] instance instance-id priority priority no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 185
with the "no" syntax, the setting returns to the default. [Example] Set the MST region name to "Test1". SWR2311P(config)#spanning-tree mst configuration SWR2311P(config-mst)#region Test1 6.3.20 Set revision number of MST region [Syntax] revision revision [Parameter] revision : Revision - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 186
this command for the corresponding LAN/SFP port returns to the default. [Example] Set MST instance #2 for LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree instance 2 6.3.22 Set interface priority for MST instance [Syntax] spanning-tree instance instance-id priority - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 187
port returns to the default. [Example] Set LAN port #1 MST instance #2 to a path cost of 100000. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#spanning-tree instance 2 SWR2311P(config-if)#spanning-tree instance 2 path-cost 100000 6.3.24 Show MST region information [Syntax] show spanning - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 188
is shown. [Note] A LAN/SFP port that is associated with a logical interface cannot be specified as ifname. [Example] Show MSTP information. SWR2311P>show spanning-tree mst % Default: Bridge up - Spanning Tree Enabled - topology change detected % Default: CIST Root Path Cost 0 - CIST Root Port - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 189
logical interface cannot be specified as ifname. [Example] Show information for MST instance #1. SWR2311P>show spanning-tree mst instance 1 % Default: MSTI Root Path Cost 0 - MSTI Timer 0 % 6.4 Loop detection 6.4.1 Set loop detection function (system) [Syntax] loop-detect switch no loop-detect - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 190
loop-detect enable Disable the loop detection function for the entire system. SWR2311P(config)#loop-detect disable 6.4.2 Set loop detection function (interface) [Syntax] loop-detect switch no loop-detect [Parameter] switch : Set loop detection function for the applicable interface Setting value - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 191
the loop detection function of LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#loop-detect disable 6.4.3 Set port blocking for loop detection [Syntax] loop-detect blocking switch no loop-detect blocking [Parameter] switch : Set port blocking for the applicable interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 192
This command can be executed only if the system-wide loop detection function is enabled. [Example] Reset the loop detection status. SWR2311P#loop-detect reset 6.4.5 Show loop detection function status [Syntax] show loop-detect [Input mode] unprivileged EXEC mode, priviledged EXEC mode [Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 193
an IPv4 address of the same subnet to multiple interfaces. [Example] Specify 192.168.1.100 as the IP address for VLAN #1. SWR2311P(config)#interface vlan1 SWR2311P(config-if)#ip address 192.168.1.100/24 7.1.2 Show IPv4 address [Syntax] show ip interface [interface] brief [Parameter] interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 194
error occurs if the specified interface is one to which an IP address cannot be assigned. [Example] Show the IP address of every VLAN interface. SWR2311P>show ip interface brief Interface IP-Address vlan1 192.168.1.100/24 vlan2 192.168.2.100/24 vlan3 unassigned Admin-Status up up up Link - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 195
server ID • Domain name [Note] [Example] Show the current DHCP client status. SWR2311P>show dhcp lease Interface vlan1 IP Address: 192.168.100.2 Expires: 2018/01/01 Set auto IP function [Syntax] auto-ip switch no auto-ip [Parameter] switch : Behavior of the auto IP function Setting - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 196
is discarded, and the IPv4 address obtained from the DHCP server is used. [Example] Enable the Auto IP function for VLAN #2. SWR2311P(config)#interface vlan2 SWR2311P(config-if)#auto-ip enable 7.2 IPv4 route control 7.2.1 Set static IPv4 route [Syntax] ip route ip_address/mask gateway [number] ip - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 197
, vlan1 C 192.168.200.0/24 is directly connected, vlan100 Show the route used for sending packets that are addressed to 192.168.100.10. SWR2311P>show ip route 192.168.100.10 Routing entry for 192.168.100.0/24 Known via "connected", distance 0, metric 0, best * is directly connected, vlan1 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 198
[Description] Shows the ARP cache. The ARP cache stores up to 508 entries (total of dynamic entries and static entries). [Example] Show the ARP cache. SWR2311P>show arp IP Address MAC Address Interface Type 192.168.100.10 00a0.de00.0000 vlan1 dynamic 192.168.100.100 00a0.de00.0001 vlan1 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 199
entry is deleted. [Example] Create a static ARP entry of IP address 192.168.100.100 and MAC address 00a0.de00.0000 connected to port1.1. SWR2311P(config)#arp 192.168.100.100 00a0.de00.0000 port1.1 7.3.4 Set ARP timeout [Syntax] arp-ageing-timeout time no arp-ageing-timeout [time] [Parameter - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 200
it. Show statistical information when the command ends. [Example] Ping the IP address 192.168.100.254 three times with a data size of 120 bytes. SWR2311P#ping 192.168.100.254 repeat 3 size 120 PING 192.168.100.254 (192.168.100.254): 120 data bytes 128 bytes from 192.168 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 201
7.681 ms 7.5 IPv6 address management 7.5.1 Set IPv6 [Syntax] ipv6 switch no ipv6 [Parameter] switch : Behavior of the IPv6 Setting value enable disable Description Enable the IPv6 [Example] Enable IPv6 for VLAN #1. SWR2311P(config)#interface vlan1 SWR2311P(config-if)#ipv6 enable 7.5.2 Set IPv6 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 202
an IPv6 address of the same subnet to multiple interfaces. [Example] Specify 2001:db8:1::2 as the IPv6 address for VLAN #1. SWR2311P(config)#interface vlan1 SWR2311P(config-if)#ipv6 address 2001:db8:1::2/64 7.5.3 Set RA for IPv6 address [Syntax] ipv6 address autoconfig no ipv6 address [Initial - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 203
SWR2311P>show ipv6 interface brief Interface IPv6-Address Link-Status vlan1 2001:db8:1::2/64 setting. [Example] For the destination 2001:db8:2::/64, set the gateway to 2001:db8:1::1. SWR2311P(config)#ipv6 route 2001:db8:2::/64 2001:db8:1::1 Set the default gateway to fe80::2a0:deff:fe:1 on VLAN - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 204
:1::1, vlan1, 00:01:52 C fe80::/64 via ::, vlan1, 00:03:08 Show the route used for sending packets that are addressed to 2001:db8:1::2. SWR2311P>show ipv6 route 2001:db8:1::2 Routing entry for 2001:db8:1::/64 Known via "connected", distance 0, metric 0, best Last update 00:18:27 ago * directly - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 205
is deleted. [Note] [Example] Set the MAC address of IPv6 2001:db8:cafe::1 located at port1.1 of VLAN #1, in the Neighbor cache. SWR2311P(config)#ipv6 neighbor 2001:db8:cafe::1 vlan1 00a0.de80.cafe port1.1 7.7.2 Show neighbor cache table [Syntax] show ipv6 neighbors [Input mode] unprivileged EXEC - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 206
cache table [Syntax] clear ipv6 neighbors [Input mode] priviledged EXEC mode [Description] Clears the neighbor cache. [Note] [Example] Clear the neighbor cache. SWR2311P#clear ipv6 neighbors 7.8 IPv6 ping MAC Address 0011.2233.4455 00a0.de80.cafe 0011.2233.4455 6677.8899.aabb Interface vlan1 vlan1 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 207
command ends. [Note] [Example] Ping fe80::2a0:deff:fe11:2233. SWR2311P#ping6 fe80::2a0:deff:fe11:2233%vlan1 PING fe80::2a0:deff:fe11:2233% client 7.9.1 Set DNS lookup function [Syntax] dns-client switch no dns-client [Parameter] switch : Behavior of the DNS client Setting value enable disable - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 208
the DNS lookup function. If this command is executed with the "no" syntax, the function is disabled. [Example] Enable the DNS lookup function. SWR2311P(config)#dns-client enable 7.9.2 Set DNS server list [Syntax] dns-client name-server server no dns-client name-server server [Parameter] server - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 209
the default domain name automatically specified by the ip address dhcp command are not used. [Example] Set the default domain name to "example.com". SWR2311P(config)#dns-client domain-name example.com 7.9.4 Set search domain list [Syntax] dns-client domain-list name no dns-client domain-list name - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 210
3 functions Item Domain list Name Servers Description Search domain list DNS server list (IP address) [Example] Show the DNS client information. SWR2311P>show dns-client DNS client is enabled Default domain : example.com Domain list : example1.com example2.com Name Servers : 192.168.100 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 211
/MLD query when topology changes, and set the wait time to 5 seconds. SWR2311P(config)#l2-mcast snooping tcn-query enable 5 Disable transmission of an IGMP/MLD query when topology changes. SWR2311P(config)#l2-mcast snooping tcn-query disable 8.1.2 Set processing method for unknown multicast frames - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 212
| IP multicast control [Example] Discard unknown multicast. SWR2311P(config)#l2-unknown-mcast discard 8.2 IGMP snooping 8.2.1 Set enable/disable IGMP snooping [Syntax] ip igmp snooping switch no ip igmp snooping [Parameter] switch : IGMP snooping operations enable disable Setting value - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 213
the specified LAN/SFP port. [Example] Specify LAN port #8 as a connection destination of the multicast router. SWR2311P#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#ip igmp snooping mrouter interface port1.8 Remove LAN port #8 as a connection destination of the multicast - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 214
#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#no ip igmp snooping query-interval 8.2.6 Set TTL value verification function for IGMP packets [Syntax] ip igmp snooping check ttl switch no ip igmp snooping check ttl [Parameter] switch : TTL value verification function - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 215
only if IGMP snooping is enabled. [Example] Enable the TTL value verification function of IGMP packets for VLAN #2. SWR2311P#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#ip igmp snooping check ttl enable Disnable the TTL value verification function of IGMP packets for VLAN - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 216
router connection port information that was dynamically learned or statically set. [Example] Show multicast router connection port information for VLAN #2. SWR2311P#show ip igmp snooping mrouter vlan2 VLAN Interface IP-address Expires 2 port1.8(dynamic) 192.168.100.216 00:00:49 8.2.9 Show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 217
EXEC mode, priviledged EXEC mode [Description] Shows IGMP-related information for a VLAN interface. [Example] Show IGMP-related information for VLAN #1. SWR2311P#show ip igmp snooping interface vlan1 IGMP Snooping information for vlan1 IGMP Snooping enabled Snooping Querier none IGMP Snooping other - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 218
] Clear IGMP group membership entries for VLAN #1. SWR2311P#clear ip igmp snooping interface vlan1 8.3 MLD snooping 8.3.1 Enable/disable MLD snooping [Syntax] ipv6 mld snooping switch no ipv6 mld snooping [Parameter] switch : MLD snooping operations enable disable Setting value Description - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 219
the specified LAN/SFP port. [Example] Specify LAN port #8 as a connection destination of the multicast router. SWR2311P#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#ipv6 mld snooping mrouter interface port1.8 Remove LAN port #8 as a connection destination of the multicast - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 220
config-if)#ipv6 mld snooping query-interval 30 Return the VLAN #2 query transmission interval to the default setting. SWR2311P#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#no ipv6 mld snooping query-interval 8.3.6 Set MLD version [Syntax] ipv6 mld snooping version version - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 221
forwarded as a V1 query • If a V1 report is received, it is forwarded as a V2 report [Example] On VLAN #2, set the MLD version to 1. SWR2311P#configure terminal SWR2311P(config)#interface vlan2 SWR2311P(config-if)#ipv6 mld snooping version 1 On VLAN #2, return the MLD version to the default setting - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 222
::a00:27ff:fe8b:87e3 Show detailed MLD group membership information. Interface port1.3 Uptime Expires Last 00:00:44 00:01:07 SWR2311P#show ipv6 mld snooping groups detail MLD Snooping Group Membership Details Flags: (R - Remote, S - Static) Interface: port1.3 Group: ff15::1 Uptime: 00:00 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 223
: VLAN interface name Interface to clear [Input mode] priviledged EXEC mode [Description] Clears MLD group membership entries. [Example] Clear MLD group membership entries for VLAN #1. SWR2311P#clear ipv6 mld snooping interface vlan1 Command Reference | IP multicast control | 223 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 224
224 | Command Reference | Traffic control Chapter 9 Traffic control 9.1 ACL 9.1.1 Generate IPv4 access list [Syntax] access-list ipv4-acl-id [seq_num] action protocol src-info [src-port] dst-info [dst-port] [ack] [fin] [psh] [rst] [syn] [urg] no access-list ipv4-acl-id [seq_num] [action protocol - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 225
src-port dst-info dst-port Setting value A.B.C.D/M host A.B.C.D any Command Reference | Traffic control | 225 Description Specifies an IPv4 address (A.B.C.D) with subnet mask length (Mbit) Specifies a single IPv4 address (A.B.C.D) Applies to all IPv4 addresses : If protocol is specified - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 226
communication from source segment 192.168.1.0/24 to destination 172.16.1.1, and add the comment "Test." SWR2311P(config)#access-list 1 deny any 192.168.1.0 0.0.0.255 host 172.16.1.1 SWR2311P(config)#access-list 1 description Test 9.1.3 Apply IPv4 access list [Syntax] access-group ipv4-acl-id - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 227
numbered port is applied to the logical interface. [Example] Apply extended IPv4 access list #1 to received frames of LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#access-group 1 in 9.1.4 Generate IPv6 access list [Syntax] access-list ipv6-acl-id [seq_num] action src-info no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 228
.) [Example] Create IPv6 access list #3002 which denies frames from 3ffe:506::/32, and add the comment "Test." SWR2311P(config)#access-list 3002 deny 3ffe:506::/32 SWR2311P(config)#access-list 3002 description Test 9.1.6 Apply IPv6 access list [Syntax] access-group ipv6-acl-id direction no access - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 229
lowest-numbered port is applied to the logical interface. [Example] Apply IPv6 access list #3002 to received frames of LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#access-group 3002 in 9.1.7 Generate MAC access list [Syntax] access-list mac-acl-id [seq_num] action src-info - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 230
MAC access list #2001 which denies frames from MAC address 00-A0-DE-12-34-56. SWR2311P(config)#access-list 2001 deny mac 00A0.DE12.3456 0000.0000.0000 any Delete MAC access list #2001. SWR2311P(config)#no access-list 2001 9.1.8 Add comment to MAC access list [Syntax] access-list mac-acl - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 231
list #2000 which denies frames from MAC address 00-A0-DE-12-34-56, and add the comment "Test." SWR2311P(config)#access-list 2001 deny mac 00A0.DE12.3456 0000.0000.0000 any SWR2311P(config)#access-list 2001 description Test 9.1.9 Apply MAC access list [Syntax] access-group mac-acl-id direction no - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 232
only for the one that was applied first. [Example] Show all lists. SWR2311P>show access-list IPv4 access list 1 10 deny any 192.168.1.0/24 host 172 by the "show access-list" command. [Example] Clear counters. SWR2311P>clear access-list counters 9.1.12 Show access list applied to interface - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 233
priviledged EXEC mode, use the end command. [Example] Create a VLAN access map named "VAM001", and move to VLAN access map mode. SWR2311P(config)#vlan access-map VAM001 SWR2311P(config-vlan-access-map)# 9.1.14 Set access list for VLAN access map [Syntax] match access-list list-id no match access - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 234
map. The following items are shown. • Name of the VLAN access map • Access list applied to VLAN access map [Example] Show VLAN access map information. SWR2311P>show vlan access-map Vlan access-map VAM001 match ipv4 access-list 2 9.1.17 Show VLAN access map filter [Syntax] show vlan filter - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 235
VLAN ID applied to VLAN access map [Example] Show VLAN access map filter information. SWR2311P>show vlan filter Vlan Filter VAM001 is applied to vlan 1000 9.2 QoS (Quality of Service) 9.2.1 Enable/disable QoS [Syntax] qos action qos_disable [Parameter] action : Operation for Qos enable disable - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 236
for the lowest-numbered port is applied to the logical interface. [Example] Set the default CoS value to 2. SWR2311P(config-if)#qos cos 2 Return the default CoS value to the default value. SWR2311P(config-if)#no qos cos 9.2.3 Set trust mode [Syntax] qos trust mode no qos trust [Parameter] mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 237
[Description] Shows the enabled (Enable) or disabled (Disable) status of the QoS function. [Example] Show the status of the system's QoS setting. SWR2311P#show qos Enable 9.2.5 Show QoS information for interface [Syntax] show qos interface [ifname] [Parameter] ifname : Name of the LAN/SFP port or - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 238
trust mode. [Note] In order to execute this command, QoS must be enabled. [Example] Show the QoS settings of LAN port #1. (trust mode CoS) SWR2311P#show qos interface port1.1 Port Trust Mode: CoS Port Default CoS Priority: 0 Egress Traffic Shaping: Rate 30016 Kbps, Burst 1876 KByte Queue Scheduling - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 239
command can be used regardless of the QoS status (enabled/disabled). [Example] Show the queue usage ratio of LAN port #1. SWR2311P#show qos queue-counters port1.1 QoS: Enable Interface port1.1 Queue Counters: Queue 0 59.4 % Queue 1 15.0 % Queue 2 0.0 % Queue 3 0.0 % Queue 4 0.0 % Queue - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 240
shows the default settings of the CoS - egress queue ID conversion table. CoS value Egress queue 0 2 1 0 2 1 3 3 4 4 5 5 6 6 7 7 [Example] Assign egress queue #4 to CoS value "0". SWR2311P(config)#qos cos-queue 0 4 Return the egress queue ID of CoS value "0" to the default value - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 241
interface. [Example] Assign egress queue ID #4 as the port priority for LAN port #1. SWR2311P#interface port1.1 SWR2311P(config-if)#qos port-priority-queue 4 9.2.10 Specify egress queue of frames transmitted from the switch itself [Syntax] qos queue sent-from-cpu queue-id no qos queue sent-from-cpu - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 242
for the storage destination of frames sent to each LAN/SFP port from the switch itself (CPU). If this is executed with the "no" syntax, the #5 as the storage destination egress queue for frames sent from the CPU. SWR2311P(config)#qos queue sent-from-cpu 5 9.2.11 Generate class map (traffic category - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 243
police 48 12 12 yellow-action remark red-action drop SWR2311P(config-pmap-c)#remark-map yellow ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.13 Set traffic classification conditions (access - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 244
for traffic categorization in an access list. [Example] Specify access list #1 as the classification conditions for class map "class1." SWR2311P(config)#class-map class1 SWR2311P(config-cmap)#match access-list 1 9.2.14 Set traffic classification conditions (CoS) [Syntax] match cos cos-list no match - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 245
, QoS must be enabled. [Example] Specify DSCP values "48" and "56" as the classification conditions for class map "class1." SWR2311P(config)#class-map class1 SWR2311P(config-cmap)#match ip-dscp 48 56 9.2.17 Set traffic classification conditions (Ethernet Type) [Syntax] match ethertype type match - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 246
to execute this command, QoS must be enabled. [Example] Specify VLAN #20 as the classification conditions for class map "class1". SWR2311P(config)#class-map class1 SWR2311P(config-cmap)#match vlan 20 9.2.19 Set traffic classification conditions (VLAN ID range) [Syntax] match vlan-range id-start to - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 247
this command, QoS must be enabled. [Example] Specify VLAN #20 through #30 as the classification conditions for class map "class1". SWR2311P(config)#class-map class1 SWR2311P(config-cmap)#match vlan-range 20 to 30 9.2.20 Show class map information [Syntax] show class-map [name] [Parameter] name - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 248
-pmap-c)#police 48 12 12 yellow-action remark red-action drop SWR2311P(config-pmap-c)#remark-map yellow ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.22 Apply policy map for received frames - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 249
[Example] Apply policy map "policy1" to LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 Remove policy map "policy1" from LAN port #1. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#no service-policy input policy1 9.2.23 Set pre-marking (CoS - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 250
(config-cmap)#exit [Policy settings] SWR2311P(config)#policy-map policy1 SWR2311P(config-pmap)#class class1 SWR2311P(config-pmap-c)#set cos 2 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.24 Set pre - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 251
(config-cmap)#exit [Policy settings] SWR2311P(config)#policy-map policy1 SWR2311P(config-pmap)#class class1 SWR2311P(config-pmap-c)#set ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.26 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 252
policy1 SWR2311P(config-pmap)#class class1 SWR2311P(config-pmap-c)#police 48 12 12 yellow-action remark red-action drop SWR2311P(config-pmap-c)#remark-map yellow ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 253
) for the categorized traffic classes. If the setting was already made by the police command, its content is changed. Metering on the SWR2311P is implemented as a single-rate three-color marker (RFC2697), and the following processing can be specified for the categorized bandwidth classes. • Green - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 254
-rate 48 96 12 12 yellow-action remark red-action drop SWR2311P(config-pmap-c)#remark-map yellow ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.28 Set remarking of individual policers [Syntax - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 255
police 48 12 12 yellow-action remark red-action drop SWR2311P(config-pmap-c)#remark-map yellow ip-dscp 10 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.29 Generate aggregate policer [Syntax] aggregate - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 256
policer as an aggregate policer. If this is executed with the "no" syntax, metering/policing/remarking processing is deleted. Metering on the SWR2311P is implemented as a single-rate three-color marker (RFC2697), and the following processing can be specified for the categorized bandwidth classes - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 257
policer as an aggregate policer. If this is executed with the "no" syntax, metering/policing/remarking processing is deleted. Metering on the SWR2311P is implemented as a single-rate three-color marker (RFC2697), and the following processing can be specified for the categorized bandwidth classes - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 258
• Executing metering by TrTCM with CIR:48kbps, PIR:96kbps, CBS:12kbyte, and PBS:12kbyte • Yellow: rewrite DSCP value to 10, Red: discard [Aggregate policer creating] SWR2311P(config)#aggregate-police AGP-01 SWR2311P(config-agg-policer)#police twin-rate 48 96 12 12 yellow-action remark redaction drop - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 259
the show classmap command. [Note] In order to execute this command, QoS must be enabled. [Example] Show the contents of aggregate policer "AGP-01". SWR2311P#show aggregate-police AGP-01 Aggregator-Police Name: AGP-01 Mode: TrTCM average rate (48 Kbits/sec) peak rate (96 Kbits/sec) burst size (12 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 260
-pmap-c)#police-aggregate AGP-01 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#class class2 SWR2311P(config-pmap-c)#police-aggregate AGP-01 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.35 Show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 261
(config-cmap)#exit [Policy settings] SWR2311P(config)#policy-map policy1 SWR2311P(config-pmap)#class class1 SWR2311P(config-pmap-c)#set cos-queue 3 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.38 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 262
-cmap)#exit [Policy settings] SWR2311P(config)#policy-map policy1 SWR2311P(config-pmap)#class class1 SWR2311P(config-pmap-c)#set ip-dscp-queue 24 SWR2311P(config-pmap-c)#exit SWR2311P(config-pmap)#exit SWR2311P(config)#interface port1.1 SWR2311P(config-if)#service-policy input policy1 9.2.39 Show - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 263
(match, set, police) has not been specified. [Note] In order to execute this command, QoS must be enabled. [Example] Show information for policy map "policy1". SWR2311P#show policy-map policy1 Policy-Map Name: policy1 State: attached Class-Map Name: class1 Qos-Access-List Name: 1 Police: Mode: SrTCM - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 264
map or class map. [Note] In order to execute this command, QoS must be enabled. [Example] Show the status of policy map "policy1". SWR2311P#show qos map-status policy policy1 policy1 status input port : port1.3 edit/erase : Disable attach limitation CoS trust mode : Enable DSCP trust mode - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 265
(config)#no qos wrr-weight 7 SWR2311P(config)#no qos wrr-weight 6 SWR2311P(config)#qos wrr-weight 5 5 SWR2311P(config)#qos wrr-weight 4 5 SWR2311P(config)#qos wrr-weight 3 5 SWR2311P(config)#qos wrr-weight 2 2 SWR2311P(config)#qos wrr-weight 1 1 SWR2311P(config)#qos wrr-weight 0 1 9.2.42 Set - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 266
23476 17.28 23477 - 1000000 261 [Example] Reduce transmission from LAN port #1 down to CIR:30016 kbps, Bc:1876000 byte. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#traffic-shape rate kbps 30016 burst 1876 9.2.43 Set traffic-shaping (queue units) [Syntax] traffic-shape queue queue-id - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 267
.28 23477 - 1000000 261 [Example] Reduce transmission from queue #0 of LAN port #1 down to CIR:10 Mbps and Bc:64000 byte. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#traffic-shape queue 0 rate kbps 10000 burst 64 9.3 Flow control 9.3.1 Set flow control (IEEE 802.3x PAUSE send/receive - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 268
enabled or disabled as a set. (It is not possible to enable only send or receive.) The period of pause time requested when the SWR2311P transmits a PAUSE frame is 0xFFFF (65535). The following limitations apply. • It is not possible to specify "flowcontrol auto" for a combo port. [Example] Enable - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 269
] Enable broadcast storm control and multicast storm control for LAN port #1, and set the threshold value to 30%. SWR2311P(config)#interface port1.1 SWR2311P(config-if)#storm-control broadcast multicast level 30 9.4.2 Show storm control reception upper limit [Syntax] show storm-control [ifname - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 270
upper limit value for frame reception. If the interface name is omitted, all interfaces are shown. [Example] Show the setting status of all interfaces. SWR2311P#show storm-control Port BcastLevel McastLevel port1.1 30.00% 30.00% port1.2 20.00% 20.00% port1.3 100.00% 100.00% port1.4 100.00 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 271
start 107 config-auto-set enable 101 copy auth-web custom-file 150 copy running-config startup-config 31 copy startup-config 34 copy tech-support sd 40 D description 112 dns-client 207 dns-client domain-list 209 dns-client domain-name 208 dns-client name-server 208 dot1x control-direction - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 272
ipv6 mld snooping querier 219 ipv6 mld snooping query-interval 220 ipv6 mld snooping version 220 ipv6 neighbor 205 ipv6 route 203 L l2-mcast snooping tcn-query 211 l2-unknown-mcast 211 l2ms configuration 94 l2ms enable 94 l2ms filter enable 97 l2ms reset 98 l2ms role 95 lacp port-priority 133 - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 273
S save logging 49 service terminal-length 45 service-policy 248 set cos 249 set cos-queue 261 set ip- host key 79 show startup-config 32 show static-channel-group 125 show storm-control 269 show tech-support 39 show telnet-server 67 show tftp-server 70 show users 29 show vlan 172 show vlan access- - Yamaha SWR2311P-10G | SWR2311P-10G Command Reference - Page 274
274 | Command Reference | Index spanning-tree forward-time 174 spanning-tree instance 185 spanning-tree instance path-cost 186 spanning-tree instance priority 186 spanning-tree link-type 176 spanning-tree max-age 174 spanning-tree mst configuration 183 spanning-tree path-cost 177 spanning-tree
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
 |
 |
Yamaha L2 Switch
Intelligent L2 PoE SWR2311P-10G
Command Reference
Rev.2.02.14