2013 Dodge Avenger User Guide - Page 65

2013 Dodge Avenger Manual

Get 2013 Dodge Avenger PDF manuals and user guides View all 2013 Dodge Avenger manuals

Page 65 highlights

ELECTRONICS NOTE: Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code • For programming Garage Door Openers that were manufactured after 1995. These Garage Door Openers can be identified by the "LEARN" or "TRAIN" button located where the hanging antenna is attached to the Garage Door Opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. • Place the ignition switch into the ON/RUN position. • Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. • Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button. • Continue to hold both buttons and observe the indicator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. • At the garage door opener motor (in the garage), locate the "LEARN" or "TRAINING" button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly press and release the "LEARN" or "TRAINING" button. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. • Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. NOTE: If the device does not activate, press the button a third time (for two seconds) to complete the training. • To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. Programming A Non-Rolling Code • For programming Garage Door Openers manufactured before 1995. • Turn the ignition switch to the ON/RUN position. • Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
NOTE:
ErasingallchannelsshouldonlybeperformedwhenprogrammingHomeLink®forthefirst
time.Donoterasechannelswhenprogrammingadditionalbuttons.
• Ifyouhaveanyproblems,orrequireassistance,pleasecalltoll-free1–800–355–3515or,
ontheInternetatwww.HomeLink.comforinformationorassistance.
ProgrammingARollingCode
• For programming Garage Door Openers that were manufactured after 1995. These
GarageDoorOpenerscanbeidentifiedbythe“LEARN”or“TRAIN”buttonlocatedwhere
thehangingantennaisattachedtotheGarageDoorOpener.ItisNOTthebuttonthatis
normallyusedtoopenandclosethedoor.Thenameandcolorofthebuttonmayvaryby
manufacturer.
• PlacetheignitionswitchintotheON/RUNposition.
• Placethehand-heldtransmitter1to3in(3to8cm)awayfromtheHomeLink®buttonyou
wishtoprogramwhilekeepingtheHomeLink®indicatorlightinview.
• SimultaneouslypressandholdboththeHomeLink®buttonyouwanttoprogramandthe
hand-heldtransmitterbutton.
• Continuetoholdbothbuttonsandobservetheindicatorlight.TheHomeLink®indicator
willflashslowlyandthenrapidlyafterHomeLink®hasreceivedthefrequencysignalfrom
thehand-heldtransmitter.Releasebothbuttonsaftertheindicatorlightchangesfrom
slowtorapid.
• Atthegaragedooropenermotor(inthegarage),locatethe“LEARN”or“TRAINING”
button.Thiscanusuallybefoundwherethehangingantennawireisattachedtothe
garagedooropenermotor.Firmlypressandreleasethe“LEARN”or“TRAINING”button.
NOTE:
Youhave30secondsinwhichtoinitiatethenextstepaftertheLEARNbuttonhasbeen
pressed.
• ReturntothevehicleandpresstheprogrammedHomeLink®buttontwice(holdingthe
buttonfortwosecondseachtime).Ifthedeviceispluggedinandactivates,program-
mingiscomplete.
NOTE:
Ifthedevicedoesnotactivate,pressthebuttonathirdtime(fortwoseconds)tocomplete
thetraining.
• ToprogramtheremainingtwoHomeLink®buttons,repeateachstepforeachremaining
button.DONOTerasethechannels.
ProgrammingANon-RollingCode
• ForprogrammingGarageDoorOpenersmanufacturedbefore1995.
• TurntheignitionswitchtotheON/RUNposition.
• Placethehand-heldtransmitter1to3in(3to8cm)awayfromtheHomeLink®buttonyou
wishtoprogramwhilekeepingtheHomeLink®indicatorlightinview.
ELECTRONICS
63