1998 Ford Expedition Owner Guide 1st Printing

1998 Ford Expedition Manual

Get 1998 Ford Expedition PDF manuals and user guides View all 1998 Ford Expedition manuals

1998 Ford Expedition manual content summary:

  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 1
    Contents Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Reporting safety defects Index 150 200 207 208 92 98 127 2 4 20 60 All
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 2
    , vary speeds frequently. This is necessary to give the moving parts a chance to break in. If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 3
    type vehicles Before you drive your vehicle, please read this Owner's Guide carefully. Your vehicle is not a passenger car. As with other loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the "Four Wheeling" supplement included with 4WD and utility
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 4
    Instrumentation Instrument cluster (pg. 6) Driver side air bag (pg. 78) Headlamp control (pg. 20) LOW FUEL F H E L 60 40 50 80 • 100 60 • 70 30 • 20 40• 000005 120 • 80 90 1 2 THEFT 3 4 5 ABS 20•km/h •140 • - + - + H 18 C 8 10 0 0000 100 0 RPMx1000 CHECK ENGINE 6 4X4 ON RES SET
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 5
    Instrumentation Gearshift (includes overdrive button) (pg. 104) Electronic sound system; refer to Audio Guide (pg. 23) VOL-PUSH ON AM FM FM 1 FM 1 BASS TREB ST BAL FADE AUTO SET SEEK DISCS REW 1 TUNE SCAN EJ DOLBY 8 NR TAPE CD FF 2 SIDE 1-2 3 4 COMP 5 SHUFFLE 6 LO A4WD LO FLOOR
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 6
    Instrumentation WARNING LIGHTS AND CHIMES LOW FUEL F H E DOOR AJAR BRAKE 40 60 30 20 40 50 60 80 100 000000 120 70 80 140 3 2 THEFT 4 FUEL DOOR ABS L H 18 C 8 ! - + 10 0 20 km/h 160 90 1 0 5 6 FUEL RESET CHECK SUSP LOW WASH LOW RANGE 4X4 MPH 0 0 0 0 100 RPM X1000 CHECK ENGINE
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 7
    control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing. What you should do if the check engine light illuminates Light present, the Check Engine light should turn off. (A
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 8
    your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Air bag readiness Momentarily illuminates
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 9
    after releasing the parking brake indicates low brake fluid level. Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned on and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. Turn signal
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 10
    system serviced. Refer to SecuriLock௢ anti-theft system in the Controls and features chapter. Charging system Momentarily illuminates when the ignition is turned ON and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Oil
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 11
    Instrumentation oil pressure gauge in this chapter for more air suspension Illuminates momentarily when the ignition is turned to the ON position and the engine is OFF. The light also illuminates when the air suspension system requires servicing. For information on the air suspension system
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 12
    fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. LOW WASH DOOR AJAR FUEL
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 13
    ignition is off (and the key is not in the ignition) and either front door is opened. GAUGES LOW FUEL F H E DOOR AJAR BRAKE 40 60 30 20 40 50 60 80 100 000000 120 70 80 140 3 2 1 0 THEFT FUEL DOOR ABS 4 5 6 FUEL RESET 4X4 CHECK SUSP LOW WASH LOW RANGE L H 18 C 8 ! - + 10 0 20 km/h 160
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 14
    Instrumentation than the advertised capacity due to the reserve fuel. Speedometer Indicates the current vehicle speed. 40 60 30 20 10 0 40 50 60 80 100 000000 120 70 80
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 15
    /h 160 90 MPH 0 0 0 0 100 Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 50 60 80 100 40 60 30 20 10 0 40 000000 120 70 80 140 20 km/h 160 90 MPH 0 0 the top of the scale may damage the engine. 3 2 1 0 4 FUEL DOOR 5 6 RPM X1000 15
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 16
    the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician. TRIP COMPUTER The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems. You may select display features on
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 17
    vehicle's option package, but the functions are the same. The trip computer only works when the ignition is in the ON position. Trip computer features follow: Selectable features English/metric display Press this control to change the trip computer display from metric to English units. Press again
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 18
    indicate the vehicle's average fuel economy in liters/100 km (or miles/gallon) since last reset. • To reset the average fuel economy: 1. Press the MODE control repeatedly until AVG F/ECON is displayed (no other display is resettable). 2. Press the E/M and MODE
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 19
    Instrumentation Press the MODE control one final time to turn the trip computer display off. MODE RESET MILES TO EMPTY E/M 19
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 20
    on. The foglamp indicator light (located to the right of the control) will illuminate. Daytime running light (Canadian vehicles only) The daytime running light system turns the headlamps on, with a reduced light output, when: • the vehicle is running • the parking brake is released • the headlamp
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 21
    turn on. • Rotate all the way down to override. AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a preselected period of time after the ignition
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 22
    the position and pull for fog. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. • is turned to the OFF position. To manually turn off the defroster before ten minutes have passed, push the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 23
    the Control-Trac 4WD. Refer to Control trac automatic four-wheel drive system in the Driving chapter for more information. A4WD 4H 4L 2H AUDIO SYSTEM Refer to the "Audio Guide" for instructions on how to operate the audio system. CLIMATE CONTROL SYSTEM Manual heating and air conditioning system
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 24
    while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to "breathe" through the outside air inlet duct. • MAX
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 25
    from entering the vehicle. PANEL & FLOOR-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 26
    Controls and features • FLR & DEF-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 27
    three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally. • When placing objects on top of your instrument panel defroster outlets and block airflow and possibly damage your climate control system. 27
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 28
    not be equipped with rear console audio/climate controls. Turn the air distribution control to the desired airflow position. The instrument panel climate controls must be on in order for the rear climate control console controls to work. Turn the fan speed control to the desired position. - VOLUME
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 29
    and features Select for air to flow through these vents: - VOLUME + BAND SEEK MEMORY Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle. Besides the driver's overhead control panel for the front seat
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 30
    for the auxiliary A/C-heater to operate. When the auxiliary A/C-heater control is set to FLOOR, airflow only occurs from the third row seat floor vent located in the driver's side rear quarter trim panel. When the auxiliary A/C-heater control is set to PANEL, airflow occurs from the overhead 2nd and
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 31
    and features Turn the temperature control to the desired temperature. COOL WARM OFF LO You can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: • Far left for airflow to the overhead registers. • Far right for
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 32
    the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine. Release the key as soon as the engine starts. TURN SIGNAL CONTROL
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 33
    roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition. ON OFF Once speed control is switched off, the previously programmed set speed will be erased. 33
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 34
    vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a , you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 35
    the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or • Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or RES SET
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 36
    . When the desired vehicle speed is reached, press SET ACC/SET ACCEL. RES SET ACCEL COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. ON OFF
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 37
    than 48 km/h (30 mph). RES SET ACCEL COAST TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. 37
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 38
    and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 39
    and features INT 1 - Ten second interval rear wiper. OFF - Rear wiper and washer off. Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle's speed increases. HIGH BEAMS Push forward to activate
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 40
    automatically return to normal (Overdrive) mode. OVERHEAD CONSOLE The appearance of your vehicle's overhead console will vary according to your option package. Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 41
    (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place Velcro௢ hook onto back side of aftermarket transmitter opposite of actuator control. • Place transmitter into storage compartment, control down. • Place the provided height
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 42
    . • Press and hold (as desired) the front portion of the moon roof control to close. • To halt motion at any point during one-touch opening, press the control a second time. • The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut. • To close the shade
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 43
    Controls and features Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual in for your geographic location by referring to the zone map. 1 2 3 13
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 44
    Controls and features 2. Locate the compass module mounted at the base of the mirror. 3. Turn ignition steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 45
    Controls and features 2. Locate the compass module mounted on the base of the mirror. 3. Insert an rear windows (if equipped) portion of the VENT Press the control to open the power rear quarter windows. portion of the VENT Press the control to close the power rear quarter windows. VENT VENT MODE
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 46
    will change from the normal state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will automatically adjust to minimize glare. Press the control to turn the mirror on or off. The mirror will automatically return to
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 47
    Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close.
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 48
    Controls and features Window lock The window lock feature allows only the driver to operate the power windows. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either door is opened. POWER
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 49
    Controls and features Relock The autolock feature repeats when: • any door is opened and closed • the brake pedal is released. Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the liftgate window are closed. You
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 50
    are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the lock. Move control down to disengage childproof locks. POWER
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 51
    Controls and features 3. Return to the center your vehicle is equipped with signal mirrors, the word "signal" is located at the top of the right and left side view mirrors. When the cannot see the arrow. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: •
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 52
    located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the powerpoint. COMPACT DISC CHANGER (IF EQUIPPED) The compact disc changer is located inside the front center console. For information on the compact disc changer, refer to the "Audio Guide
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 53
    Controls and features POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake . DOOR GLASS 53
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 54
    . This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. SECURILOCKி ANTI-THEFT SYSTEM Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 55
    an electronic code. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. Unlocking the doors Press this control to unlock the driver door. The interior lamps and running
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 56
    all doors. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 57
    time and use • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 58
    the running board lights illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control or 58
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 59
    Controls and features • any door is open. Battery saver will shut off the interior lamps 40 minutes after the last door is closed. 59
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 60
    support control clockwise to increase softness. Front seats Never adjust the driver's seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 61
    Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the armrest (if equipped) Pull the strap to move the armrest down. To move the armrest up, lift it until it latches in the upright position. Adjusting the front power seat (if
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 62
    Seating and safety restraints Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press to raise or lower the front portion of the seat cushion. Press to
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 63
    that the second row seat head rest clears the front seat. For assistance, refer to the label located on the lower position of the opening. 1. Locate handle below the seat cushion near the bottom of the door side cushion (this handle is marked "A"). 2. Lift the handle and push the seatback toward the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 64
    restraints 3. Press the green control on the seatback to release the closeout panel. Rotate the panel to closeout the space in the floor. 4. the closeout panel onto the seatback and press the black control (adjacent to the green control) to lock. 2. Locate and lift the handle marked "A". 3. Pull on
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 65
    belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter. The third row seat may be removed from the vehicle for additional cargo space
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 66
    : • through the passenger side rear door if your vehicle has a second row bench seat • through either rear door if your vehicle has second row bucket the upright, fully latched position before putting the vehicle in motion. 1. Locate the lever at the bottom of the seatback marked "1". 2. Press down
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 67
    seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of into the vehicle floor. 3. Use the black plastic clip (located just above the detachable anchor) to stow the loose seat
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 68
    cushion. • The seatback will latch onto the cushion. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches. 5. While pulling up on prevent correct use of the safety belts and could increase the risk of injury. Refer to the warning label on the seat
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 69
    of the floor tubs. 2. Guide the positioners around each pin and lower the seat. • When the rear of the seat is 10-13 cm (4-5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor. 3. Locate the seat belt anchor tongue in the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 70
    move freely on either side of the seat. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 71
    or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Each seating position in your vehicle has a specific safety belt assembly which is made up of one
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 72
    Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of 8 km
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 73
    or Safety Seats for Children later in this chapter. How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a 73
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 74
    your waist. Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. 74
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 75
    and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 76
    assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 77
    and the warning chime is sounding...The safety belt warning light remains The driver's safety belt is buckled before the ignition key off. is turned to ON...Safety belt maintenance Check the safety belt systems periodically to make sure they work properly and are not damaged. Check the safety
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 78
    and maintaining the safety belts in the Maintenance and care section. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) LOW FUEL F E H 30 20 10 40 40 60 50 80 60 100 70 3 120 H DOOR AJAR BRAKE 000000 80 90 1 2 THEFT 4 VOL - PUSH ON 140 20 160 MPH 5 6 RPMx1000 CHECK ENGINE ABS CHECK SUSP 18
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 79
    system is designed to: • work with the safety belt to protect the driver and right front passenger • reduce certain upper body injuries Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury. The right front passenger air bag
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 80
    Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children should always wear their safety belts. Failure to follow these instructions
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 81
    restraints How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 82
    ), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 83
    the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 84
    or provincial laws for specific requirements regarding the Always follow the instructions and warnings that belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 85
    neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. If the shoulder belt cannot be properly positioned: • move the child to one of the seats with a lap belt only (if equipped) OR • if the child is the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 86
    size and weight of the child. Carefully follow all of the manufacturer's instructions with the safety seat you put in your vehicle. If you do or collision. When installing a child safety seat: • Use the correct safety belt buckle for that seating position. • Make sure the tongue is securely fastened
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 87
    safety seats with tether straps. Carefully follow all of the manufacturer's instructions included with the safety seat you put in your vehicle. If lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Air bag can kill or
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 88
    portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 89
    5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 90
    restraints able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through cushion frame. The anchor bracket must be installed using the instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions, may
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 91
    Seating and safety restraints Tether anchor brackets may also be installed to the floor behind the second row seats. Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision. 91
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 92
    START YOUR VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference-Causing idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 93
    exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine's idle revolutions per minute (RPM
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 94
    Starting • Make sure the parking brake is set. HOOD BRAKE • Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 94
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 95
    2 THEFT 4 FUEL DOOR ABS L H 18 C 8 ! - + 10 0 20 km/h 160 90 1 0 5 6 CHECK SUSP LOW WASH MPH 0 0 0 0 100 RPM X1000 CHECK ENGINE A4WD P RN D 21 FUEL RESET LOW RANGE 4X4 Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 96
    After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. They are strongly
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 97
    exhaust and body ventilation systems checked whenever: • the vehicle is raised for service • the sound of the exhaust system changes • the inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 98
    environmental conditions such as cold, heat, moisture, road dust, salt or mud. If a "metal-to-metal," "continuous grinding" or "continuous squeal" sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. Anti-lock brake system (ABS
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 99
    five seconds when starting the vehicle. If an ABS fault is detected, the light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective unless the BRAKE warning lamp is also illuminated. Using ABS • In an emergency or when maximum efficiency from
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 100
    Driving there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Parking brake Apply the parking brake whenever the vehicle is
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 101
    to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. HOOD BRAKE STEERING Your vehicle is action could damage the power steering pump. Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds,
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 102
    your dealer or a qualified service technician. AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspension system is designed to improve ride, handling and general vehicle performance for static, on and off-road driving conditions. • The load leveling feature of the air suspension automatically keeps the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 103
    air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 104
    the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF. Apply the brake pedal to Fuses and relays in the Roadside emergencies chapter. Do not drive your vehicle until you verify that the brakelamps are working. If
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 105
    not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. Driving with a 4-speed automatic
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 106
    Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 107
    • towing a trailer up or down steep hills • additional engine downhill braking is desired. If towing a trailer, refer to Driving while you tow in the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 108
    decelerates to the proper speed. CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) Your 4x4 features a heavy-duty Control-Trac system, including a computer-operated transfer case. Coupled with a center-disconnected front axle, this unique system is interactive with the road, continually
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 109
    any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles. Using the Control-Trac system Shifting to A4WD Move the 4WD control to A4WD at a stop or at speeds up to 88 km/h (55 mph). • At temperatures
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 110
    to 4L (and 4L to 4H) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4H (or 4L) position. A4WD 4H 4L 2H Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed. Shifting from 2H to 4H
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 111
    gets stuck If the vehicle is stuck, shift the transmission in a steady motion between forward and reverse gears. Allow the transmission to engage, then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 112
    slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 113
    sideways. Drive straight up, straight down or avoid the hill completely. Know the conditions on the other side of a hill before driving over the crest. When avoid sudden braking. Rapid pumping of the brake pedal will help slow the vehicle and still maintain steering control. When speed control is on
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 114
    out of (Overdrive) into D (Drive). Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like braking, apply the brakes as you normally would. In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 115
    Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver's door pillar. • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is 115
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 116
    Driving specific to each vehicle and is listed on the Safety Compliance Label on the driver's door pillar. • GCWR (Gross Combined Weight Rating): Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer. The GCWR indicates the maximum loaded weight that the vehicle
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 117
    Certification Label. Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle's GVWR and ratio. 3. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 118
    engine, transmission, axle, brakes, tires, and suspension. For your safety and Service Guide". • Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). • Refer to the instructions included with towing accessories for the proper installation and adjustment specifications
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 119
    , stop and turn lamps, back up lamps, battery charge, electric brakes (when a customer provided controller is installed) and ground. The kit included with your vehicle provides you with adaptors to attach the brake controller and convert the hitch connector for Class I trailer usage. Trailer
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 120
    the maximum loads listed on the Safety Compliance Certification label. For load specification terms found on the label, refer to Vehicle loading in this chapter. in engine damage, transmission damage, structural damage, loss of control and personal injury. Preparing to tow Use the proper equipment
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 121
    recommended for the automatic transmission system if you are planning on: doors closed, allow the vehicle to stand for several minutes so that it can level. 2. Turn the air suspension (if equipped) control to OFF. 3. Measure the height of a reference point on the front and rear bumpers at the center
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 122
    within 0-13 mm (0.5 in) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 3. 5. Turn the air suspension (if equipped) control to ON. Adjusting an equalizing hitch so the rear bumper of the vehicle is lower or higher than it was unloaded will defeat the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 123
    a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances ball with a 25.4 mm (one inch) shank diameter. The bumper has a 1 814 kg (4 000 lb.) trailer weight and 181 kg (400 lb.) tongue weight capability. Use a frame
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 124
    and transmission cooling. • Anticipate stops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Severe Duty Schedule in your "Service Guide" for more information. Towing behind another vehicle
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 125
    gearshift in P (Park) and increase idle speed. This aids engine cooling and air conditioner efficiency. • Vehicles with trailers should not be parked on a grade. If 15 cm (six inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 126
    Driving LUGGAGE RACK Load luggage at the front crossbar and adjust the rear crossbar as necessary. • Do not exceed 90.7 kg (200 lb) of luggage if the weight is placed directly on the crossbars. • Do not exceed 68 kg (150 lb) if the weight is resting directly on the roof. To adjust the luggage rack,
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 127
    lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off. FUEL PUMP Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 128
    a further check for leaks in the fuel system. The fuel pump shut-off switch is located in the passenger's foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 129
    50 amp fuse link 60 amp fuse link 80 amp fuse link 100 amp fuse link Color Tan Brown Red Light blue Yellow Light blue Natural Light green Pink Green Red Yellow Black Dark blue Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 130
    5 9 10 20 The fuses are coded as follows. Fuse/Relay Location 1 2 3 4 Fuse Amp Rating 15A 5A 25A 5A Description Flasher Relay Instrument Cluster, Overhead Trip Computer (OTC) Module Cigar Lighter Park Lamp Relay, Headlamp Relay, Autolamp Module, Remote Anti-Theft Personality (RAP) Module, Power
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 131
    emergencies Fuse/Relay Location 5 Fuse Amp Rating 15A Description Digital Transmission Range (DTR) Sensor, Daytime Running Lamps (DRL) Module, Speed Control Servo/Amplifier Assembly, Heater-A/C Control Assembly, Blend Door Actuator, Electronic Variable Orifice (EVO) Module Shift Lock Actuator
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 132
    through Main Light Switch) Instrument Cluster, Air Bag Diagnostic Monitor 4 Wheel Air Suspension (4WAS), Generic Electronic Module (GEM) Digital Transmission Range (DTR) Sensor, Junction Box Fuse/Relay Panel (Fuse 20) Air Bag Diagnostic Monitor Trailer Tow Battery Charge Relay, 4X4 Center Axle
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 133
    Roadside emergencies Fuse/Relay Location 26 Fuse Amp Rating 10A Description Daytime Running Lamps (DRL) Module, Right Headlamp (Power supplied through Multi-Function Switch) Main Light Switch, Fog Lamp Relay Left Headlamp Autolamp Module, Instrument Cluster, Transmission Control Switch (TCS) Radio
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 134
    Running Lamp Relay, Trailer Tow Backup Lamp Relay Air Bag Diagnostic Monitor All Unlock Relay, All Lock Relay, Driver's Unlock Relay Air Suspension Service Switch Horn Relay Radio, Premium Sound Amplifier, CD Changer, Rear Integrated Control Panel, Sub-Woofer Power (Fuse 3 & Fuse 5) 134 1 2 20
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 135
    Relay, Rear Wiper Down Motor Relay Auxiliary A/C Relay 4 Wheel Anti-Lock Brake System (4WABS) Module Air Suspension Solid State Compressor Relay Trailer Tow Battery Charge Relay, Engine Fuse Module (Fuse 2) Shift on the Fly Relay, Transfer Case Shift relay Power Seat Control Switch Fuel Pump Relay
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 136
    Roadside emergencies Fuse/Relay Location 27 28 29 Fuse Amp Rating 40A** 30A** 30A** Description Junction Box Fuse/Relay Panel, Heated Grid Relay Trailer Electronic Brake Controller Flip Window Relay, Hybrid Cooling Fan Relay * Mini Fuses ** Maxi Fuses Relays Relays are located in the power
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 137
    3 20A The primary battery fuses are located in the engine compartment near the battery. Ford recommends that the megafuses are serviced by a qualified service technician. Location 1 2 3 Amperage 175 175 20 Description Power Network Box Megafuse Alternator Megafuse Alternator Field Minifuse Engine
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 138
    . Slot Number 1 2 3 4 5 6 Fuse Amperage Rating 5 amp 20 amp 10 amp 10 amp 20 amp - Circuits Protected Powertrain Control Module (PCM) Trailer Tow Stop/Turn Lamps Audio Rear Integrated Control Panel (RICP), Compact Disc Changer, Radio Running Board Lamps Amplifier, Subwoofer Amplifier Not Used
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 139
    : Item Spare tire Jack, wheel nut wrench, instructions, work gloves Jack handle Location Under the vehicle, just forward of the rear bumper Behind the access panel located on the right rear quarter panel interior trim On top of the radiator support at the front of the engine compartment Removing
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 140
    Roadside emergencies Removing the jack and tools 1. Locate the access panel on the interior trim. Lift and rotate the two panel retaining clips and remove the panel. 2. Un-snap the wheel lug nut wrench, instructions and work gloves from their retaining bracket. 3. Remove the jack by turning the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 141
    Roadside emergencies 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet (located behind the interior
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 142
    turn counterclockwise but do not remove them until the wheel is raised off the ground. 7. Turn OFF the air suspension switch (if equipped). 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 143
    Roadside emergencies • Front (4x2) • Front (4x4) • Rear 143
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 144
    lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. 15. Turn on the air suspension switch (if equipped). 3 4 5 2 144
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 145
    catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing. Preparing your vehicle Also see the label on the battery. 1. Use only a 12-volt supply to start your vehicle. If you connect your battery to a 24-volt power supply you can damage your starter, ignition system
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 146
    terminals and remove any excessive corrosion before you attach the battery cables. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1. Position the vehicles so that they do not touch one another. 2. Switch
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 147
    the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the discharged battery (4). 3. After the disabled vehicle has been started, allow it to idle for a while so the engine can "relearn" its idle conditions
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 148
    Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground. On
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 149
    emergencies When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle. 149
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 150
    engine compartment for easy location. • We provide a "Service Guide" which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your "Warranty Guide" to find out which parts and services are covered. Use
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 151
    lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must "relearn" its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. Working with the engine off 1. Set the parking brake and ensure the gearshift
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 152
    . 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the hood until the lift cylinders hold it open. HOOD BRAKE IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L/5.4L engines 1 2 3 4 5 6 7 8 10 9 1. Battery 152
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 153
    3. Engine oil filler 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Power distribution box 8. Air filter assembly 9. Engine coolant recovery reservoir 10. Windshield washer fluid reservoir ENGINE OIL Checking the engine oil Check the engine oil each time
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 154
    and care 5. Locate and carefully remove the engine oil level indicator (dipstick). MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 155
    the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the fluid level is
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 156
    in severe dust and police, taxi or delivery service. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 157
    until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. MAX MIN If you use a brake fluid that is not DOT 3, you will cause
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 158
    the windshield. ENGINE COOLANT Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may 158
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 159
    not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Do not put engine coolant in the container for the windshield washer of coolant and water to bring the liquid level to the fill line on the reservoir. 159
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 160
    the cap down, turn it counterclockwise and remove it. Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 161
    recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle's cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you have to add more than
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 162
    to alternating four cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs, the engine coolant temperature gauge will move into the red area and the light illuminates. The check engine light will illuminate, indicating that vehicle service is required
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 163
    air conditioning capability. Continued operation will increase engine temperature and cause the engine to completely shut down. The vehicle will coast to a stop. As the engine temperature cools, the engine may be re-started. Take your vehicle to a service be near the center of the NORMAL band). 163
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 164
    until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the "Service Guide." Before adding any fluid, make sure the correct type is
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 165
    Maintenance and care Capacities and specifications chapter. An overfill condition of transmission fluid may cause shift at least twice a year. The fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 166
    30 minutes to allow the fluid to cool before checking. 1. Park the vehicle on a level surface and engage the parking brake. 2. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 167
    fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns JOINT AND SLIP YOKE The universal joints standard with your vehicle do not require lubrication. If the original universal joints are replaced with universal joints
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 168
    If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 169
    some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park), turn off all accessories and
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 170
    for disposal. Call your local recycling center to find out more about recycling automotive batteries. AIR CLEANER FILTER MAINTENANCE Refer to the "Service Guide" for the appropriate intervals for changing the air cleaner filter. Do not start your engine with the air cleaner removed and do not remove
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 171
    care For information on replacement air filter elements, refer to the Capacities and specifications chapter. WINDSHIELD WIPER BLADES Changing the wiper blades When replacing wiper blade assemblies, always use a Motorcraft part or equivalent. To make replacing the wipers easy, turn the ignition to ACC
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 172
    Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 173
    the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service braking (straight ahead) traction tests and does not include
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 174
    of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 175
    Adjust tire pressure to recommended specifications found on the Safety Compliance Certification control. Tire rotation Because your vehicle's tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the "Service Guide
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 176
    these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. Tires that are larger or smaller than your vehicle's original tires may guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory 176
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 177
    the vehicle's wheel house and/or body. Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 178
    Maintenance and care If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 179
    , including manganese-based compounds containing MMT. Vehicles certified to California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California reformulated gasolines. If California reformulated gasoline is not available when
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 180
    Maintenance and care control devices and systems may be adversely affected. Repair of damage problems try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a gasoline specification
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 181
    . Do not use gasolines containing methanol, which can damage critical fuel system components. Damage resulting from the use of methanol may not be covered by your warranty. Filling the fuel tank 1. Turn the engine off. After opening the fuel door, remove the cap carefully and slowly by turning it
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 182
    the tabs on the cap with the notches on the fuel filler pipe. Turn it clockwise until it stops. • Push the fuel door closed. If the check engine warning light illuminates and remains illuminated while the engine is started, the fuel cap may not be properly seated. Turn off the engine, remove
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 183
    that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the services listed in your "Service Guide" performed
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 184
    a fire. Watch for fluid leaks, strange odors, smoke, loss of oil pressure, the charging system warning light, the "Check Engine" light or the temperature warning light. These events could indicate that the emission control system is not working properly. If you smell exhaust fumes of any kind inside
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 185
    and Chimes section of your owners guide. Your vehicle may not pass the I/M test with the "check engine/service engine soon" light on. If the vehicle's powertrain system or its battery has just been serviced, the OBD-II system is reset to a "not ready for I/M test" condition. To ready the OBD-II
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 186
    Maintenance and care • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop and go, city type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 187
    . Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. At the back of the headlamp
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 188
    attachment standoff. 12. Carefully insert the headlamp assembly into the vehicle making sure the alignment pins are inserted into the proper holes and into the guide ribs. 13. Hold the headlamp assembly snugly against the vehicle and push down on the clips to lock the lamp into position. 188
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 189
    Maintenance and care Replacing parking lamp/turn signal bulbs 1. Remove screw from the top of lamp assembly. 2. Disengage lamp assembly (it has a snap fit). 3. Remove the electrical connector from the bulb by grasping the wire and pulling it rearward. 4. Remove bulb retainer ring by turning it
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 190
    Maintenance and care 9. Align top and bottom ribs of parking lamp assembly with corresponding slots on front of vehicle. 10. Push gently until parking lamp assembly seats (you will hear a snap). 11. Replace screw removed in step 1. Replacing foglamp bulbs 1. Disconnect the electrical connector from
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 191
    . 4. Replace the bulbs as needed and replace the high-mount brakelamp lens. Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp assemblies are located in the same portion of the vehicle rear, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 192
    2 9007 Front park/turn lamps 2 3157NAK Front sidemarker 2 194NA Foglamps 2 899 Turn/tail/brake lamps 2 3157K Liftgate lamp 2 916 Backup lamp 2 579 License lamp 2 168 High-mount brake See a dealer or qualified service technician lamp To replace all instrument panel lights - see your dealer 192
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 193
    The alignment of your headlamps should be checked by a qualified service technician if: 1. Oncoming motorists frequently signal you to deactivate your not activated. 2. The headlamps do not seem to provide enough light for clear night vision. 3. The headlamp beams are pointed substantially
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 194
    Customer Assistance Guide" for a accessories, such as antennas, before entering a car wash. After washing, apply the brakes several times to dry them. Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 195
    accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. Cleaning the wheels Wash with the same detergent as the body
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 196
    is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 197
    cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 198
    Maintenance and care Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter. Cleaning leather seats For routine cleaning, wipe
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 199
    And Finish Scrubbing Pads (UPC 04011-01276) are available through your local 3M distributor. Call 1-800-742-9649 for the nearest distributor in your area. PART NUMBER (Obtain Locally) (Obtain Locally) PART NAME Tanners Preserve Leather Cleaner 3M ЉType TЉ Clean and Finish Scrubbing Pads 199
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 200
    Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.6L engine 5.4L engine Air filter FA-1632 FA-1632 Fuel filter FG-872 FG-872 Battery (standard) BXT-59 BXT-59 Battery (optional) BXT-65-750 BXT-65-750 Oil filter FL-820-S FL-820-S PCV Valve EV-98 EV-233 Spark plugs*-platinum AWSF-32PP
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 201
    Capacities and specifications Fluid Windshield washer fluid Engine coolant Ford Part Name Ultra-Clear Windshield Concentrate Ford Premium Cooling System Fluid Application All Capacity to be checked or changed unless a leak is suspected, service required or the axle has been submerged in water. The
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 202
    hole. LUBRICANT SPECIFICATIONS Item Windshield washer fluid reservoir Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler door hinge and spring, hood latch, auxiliary latch Lock cylinders, swing-away spare tire carrier padlock Brake master cylinder Ford part name Ultra
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 203
    Capacities and specifications Item Engine oil Ford part Ford part name number Motorcraft 5W30 XO-5W30-QSP Super Premium Motor Oil High E8TZ-19590-A Temperature 4x4 Front Axle & Wheel Bearing Grease Ford specification WSS-M2C153-G with API Certification Mark ESA-M1C198-A 4x4 front wheel bearings,
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 204
    Capacities and specifications complete refill of Ford Traction-Lok rear axles. ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel grade Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Dimensions (1) Overall length (2) Overall width (3) Maximum height 4x2
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 205
    Capacities and specifications 4 1 3 5 2 205
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 206
    Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label located on the driver side instrument panel. AIR BAG XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 207
    if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 208
    passenger air bag ...81 Air cleaner filter ...170 Air conditioning auxiliary heater and air conditioner ...29 manual heating and air conditioning system ..23,24,26,28 Air suspension description ...102 warning light ...11 Ambulance packages ...3 Anti-lock brake system (ABS) description ...99 Battery
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 209
    cables ...147 Keys key in ignition chime ...13 Lamps interior lamps ...193 map lamps ...193 parking lamps ...189 Liftgate ...53 Lights, warning and indicator air bag ...8 anti-lock brakes (ABS) ...9 anti-theft ...10 brake ...9 charging system ...10 check engine ...6,7 door ajar ...12 engine oil
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 210
    Index Relays ...128,136 Remote entry system ...55 illuminated entry ...58 locking/unlocking doors ...55,56 replacement/additional transmitters ...58 replacing the batteries ...57 Reporting safety defects ...207 Safety restraints automatic locking mode (retractor) ...72,73,74 extension assembly ...76
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 211
    Index Windshield washer fluid and wipers checking and adding fluid ...158 checking and replacing wiper blades ...171 operation ...38 Wrecker towing ...148 211
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 212
    212
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 213
    213
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 214
    214
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 215
    215
  • 1998 Ford Expedition | Owner Guide 1st Printing - Page 216
    fuel Fuel tank capacity-4x2 without air suspension Fuel tank capacity-4x2 vehicles with air suspension and 4x4 vehicles Engine oil (with filter change) Unleaded fuel only - 87 octane 98.0L (26 gallons) 114.0L (30 gallons) Tire size and pressure Hood release Oil capacity (with filter change) Coolant
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Before driving
Introduction
2
Instrumentation
4
Controls and features
20
Seating and safety restraints
60
Starting and driving
Starting
92
Driving
98
Roadside emergencies
127
Servicing
Maintenance and care
150
Capacities and specifications
200
Reporting safety defects
207
Index
208
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage
and retrieval system or translation in whole or part is not permitted without
written authorization from Ford Motor Company.
Copyright
r
1997 Ford Motor Company
Elemental Chlorine Free
Contents
1