2013 Ford Edge Quick Reference Guide Printing 2 - Page 8

function Rearview camera* This system provides a visual display of the area behind the vehicle. The display automatically appears in the touch screen when the vehicle is in R (Reverse) and uses green, yellow and red guides to alert you of your proximity to objects. For non-touch screen vehicles, the image will appear in the 4.2-inch center stack display. * (if equipped) MyKey®* MyKey allows you to program certain driving restrictions in order to promote good driving habits. You can program things like; speed restrictions, limited volume levels and safety belt reminders. For complete information, refer to the MyKey chapter in your Owner's Manual. Comfort Heated front seats* To access heated seats, press the Climate corner on your touch screen. Press repeatedly to cycle through the various heat modes and off. If your vehicle is not equipped with a touch screen, press the hard button . * (if equipped) Tilting Head Restraints* Panoramic Vista Roof® and Power Sunshades* Blind Spot Information System (BLIS®) with Cross Traffic Alert (CTA)* BLIS uses radar sensors to help you determine if a vehicle may be in your blind spot zone. The CTA feature alerts you if a car is coming toward you when you are backing out of a parking space. BLIS and CTA will display a yellow indicator light in your exterior mirrors and the CTA will also sound tones and display messages to warn you which direction vehicles are approaching. Refer to the Driving Aids chapter in your Owner's Manual for more information. Securicode™ keyless entry system* EAsyFold® Rear folding seats* SelectShift Automatic™ transmission* Reverse sensing system* This system sounds a warning tone if there is an obstacle near the vehicle's rear bumper when the vehicle is in R (Reverse) and is traveling less than 3 mph (5 km/h). The warning tone will increase in frequency as the object gets closer. Note: Visibility aids do not replace the need to watch where the vehicle is moving. Refer to your Owner's Manual for safety information, more detail and limitations. Allows you to lock or unlock the doors using the touchpad. You will need your five digit factory code located on your owner's wallet card in the glove box. Refer to the Locks chapter in your Owner's Manual for more information on how to use SecuriCode. Gives you the ability to manually change gears if you'd like, along with a more aggressive shift schedule. To use, move the gearshift lever from D (Drive) to S (Sport). Then, simply press + or - buttons on the gearshift lever to make shifts. If equipped with steering wheel paddles, pull the right paddle (+) to upshift, pull the left paddle (-) to downshift. The controls are located near the left side of the liftgate interior opening. Press the top control to lower the right seat, or the bottom control to lower the left seat. To return the seats to their upright position, rotate the seatbacks upward until you hear a click and the seat latches. Note: This feature is operational when the vehicle is in park and the liftgate has been open for less than 10 minutes. Your vehicle's front row head restraints can be adjusted. Pull up to raise the head restraint. To lower, press the head restraint down while pressing and holding the guide sleeve adjust/ release button. Tilt the head restraint forward for additional comfort by gently pulling the top of the head restraint. Once it is in the forward-most position, tilting it forward once more will release it to the upright position. Note: Do not attempt to force the headrest backward after its tilted. Instead, continue tilting it forward until the headrest releases to the upright position. To open, press and release the overhead moonroof switch . The front and rear sunshades will open entirely, and the glass panel will open to the first position. Press again to fully open. To close, pull the switch down. The glass panel will stop at the first position. Pull again and hold to fully close the glass panel and the sunshades. To vent from a closed position, press the TILT button. To close from a venting position, pull the TILT button. The memory function allows a "one touch" recall of personalized memory features such as; driver seat positions and power mirrors. Use the memory controls located on the instrument panel to program and then recall memory positions. To Program position 1, press and hold until you hear a chime. To set a second position, press and hold until the same chime sounds. You can now use these controls to recall the set positions. memory function* 14 15