2014 Nissan Rogue Quick Reference Guide - Page 16

2014 Nissan Rogue Manual

Page 16 highlights

FIRST DRIVE FEATURES LANE CHANGE SIGNAL To signal a lane change, move the lever up or down to the point where the indicator light  begins to flash, but the lever does not latch.  The turn signal will flash 3 times automatically. For more information, refer to the "Instruments and controls (section 2)" of your Owner's Manual. WINDSHIELD WIPER AND WASHER SWITCH  Move the lever to the following positions to operate the windshield wipers: 01 Mist 03 MIST 01 OFF INT 02 LO 04 HI 05 - One sweep operation of the front wipers. 02 Intermittent - Front wipers operate intermittently and the speed can be adjusted by twisting the time control ring 03 to increase or decrease wiper speed. - Front wipers operate at a continuous low-speed. - Front wipers operate at a continuous high-speed. - Pull the lever toward you to activate the front washer. The front wipers will operate several times. - Rear wiper operates 06 09 04 Low 05 High 06 Front Washer REAR WINDSHIELD WIPER AND WASHER 07 Intermittent intermittently. 08 Low 07 INT - Rear wiper operates at a continuous low-speed. - Push the lever forward to activate the rear washer. The rear wiper will operate several times. 09 Rear Washer 08 ON WIPER BLADE REPLACEMENT PROCEDURE The windshield wipers must be in the service position in order to replace the wiper blades. To move the wiper blades to the service position, follow this procedure:  When the ignition switch is in the ON position or within 60 seconds of placing the ignition switch to the OFF position, push the windshield wiper and washer lever up to the Mist position two times in less than 0.5 seconds. The windshield wipers will move to the service position automatically, and the wiper blades can now be replaced. To move the wiper blades back to the original position:  Pull the windshield wiper and washer lever up for more than 1 second or push the lever down to operate at any wiper speed. For more information, refer to the "Instruments and controls (section 2)" and the "Maintenance and do-it-yourself (section 8)" of your Owner's Manual. 14 To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

14
To view detailed instructional videos regarding these and other features, please go to
www.nissanownersinfo.mobi
.
FIRST DRIVE FEATURES
WINDSHIELD WIPER AND WASHER SWITCH
Move the lever to the following positions to operate
the windshield wipers:
01
Mist
— One sweep operation of the
front wipers.
02
Intermittent
— Front wipers operate
intermittently and the speed can be adjusted
by twisting the time control ring
03
to
increase or decrease wiper speed.
04
Low
— Front wipers operate at a
continuous low-speed.
05
High
— Front wipers operate at a
continuous high-speed.
06
Front Washer
— Pull the lever toward you
to activate the front washer. The front wipers
will operate several times.
REAR WINDSHIELD WIPER AND WASHER
07
Intermittent
— Rear wiper operates
intermittently.
08
Low
— Rear wiper operates at a
continuous low-speed.
09
Rear Washer
— Push the lever forward
to activate the rear washer. The rear wiper will
operate several times.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order to replace the wiper blades.
To move the wiper blades to the service position, follow this procedure:
When the ignition switch is in the
ON
position or within 60 seconds of placing the
ignition switch to the
OFF
position, push the windshield wiper and washer lever up to
the Mist
position two times in less than 0.5 seconds. The windshield wipers will
move to the service position automatically, and the wiper blades can now be replaced.
To move the wiper blades back to the original position:
Pull the windshield wiper and washer lever up for more than 1 second or push the lever
down to operate at any wiper speed.
For more information, refer to the
“Instruments and controls (section 2)”
and the
“Maintenance and do-it-yourself
(section 8)”
of your Owner’s Manual.
03
01
02
04
05
MIST
OFF
INT
LO
HI
06
09
INT
ON
07
08
LANE CHANGE SIGNAL
To signal a lane change, move the lever up or down to the point where the indicator light
begins to ²ash, but the lever does not latch.
The turn signal will ²ash 3 times automatically.
For more information, refer to the
“Instruments and controls (section 2)”
of your Owner’s Manual.