ASRock 4Core1600-D800 User Manual - Page 19

Onboard Headers and Connectors

Get ASRock 4Core1600-D800 PDF manuals and user guides View all ASRock 4Core1600-D800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.10 No. 20) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.10 No. 7) PIN1 connect the blue end to the motherboard IDE1 connect the black end to the IDE devices 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1: see p.10, No. 14) (SATAII_2: see p.10, No. 12) (SATAII_3: see p.10, No. 13) (SATAII_4: see p.10, No. 11) SATAII_3 SATAII_1 Serial ATA (SATA) Data Cable (Optional) SATAII_4 SATAII_2 These four Serial ATAII (SATAII) connectors support SATA data cables for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on this motherboard. Serial ATA (SATA) Power Cable (Optional) connect to the SATA HDD power connector connect to the power supply Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
19
19
19
19
19
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.10
No. 20)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.10
No. 7)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These four Serial ATAII (SATAII)
(SATAII_1: see
p.10, No. 14)
connectors support SATA data
(SATAII_2: see
p.10, No. 12)
cables for internal storage
(SATAII_3: see
p.10, No. 13)
devices. The current SATAII
(SATAII_4: see
p.10, No. 11)
interface allows up to 3.0 Gb/s
data transfer rate.
F
LOPP
Y
1
P
i
n1
the red-striped side to Pin1
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
I
D
E
1
PIN1
SATAII_3
SATAII_4
80-conductor ATA 66/100 cable
SATAII_1
SATAII_2
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on this motherboard.
connect
to the SATA
HDD power connector
connect
to
the power
supply
Serial ATA (SATA)
Please connect the black end of
Power Cable
SATA power cable to the power
(Optional)
connector on each drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.