ASRock H61MV-ITX User Manual - Page 28

Onboard Headers and Connectors

Get ASRock H61MV-ITX PDF manuals and user guides View all ASRock H61MV-ITX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2.10 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors (SATA_0 (PORT 0): see p.14, No. 4) SATA_0 (PORT 0) SATA_2 (PORT 4) (SATA_1 (PORT 1): see p.14, No. 3) (SATA_2 (PORT 4): SATA_1 (PORT 1) SATA_3 (PORT 5) see p.14, No. 5) (SATA_3 (PORT 5): see p.14, No. 6) These four Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. The current SATA2 interface allows up to 3.0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATA2 hard disk or the SATA2 connector on this motherboard. USB 2.0 Headers (9-pin USB4_5) (see p.14 No. 7) (9-pin USB6_7) (see p.14 No. 8) Besides four default USB 2.0 ports on the I/O panel, there are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports. Consumer Infrared Module Header (4-pin CIR1) (see p.14 No. 9) This header can be used to connect the remote controller receiver. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
28
2.10 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
Serial ATA2 Connectors
These four Serial ATA2
(SATA_0 (PORT 0):
(SATA2) connectors support
see
p.14, No. 4)
SATA data cables for internal
(SATA_1 (PORT 1):
storage devices. The current
see
p.14, No. 3)
SATA2 interface allows up to
(SATA_2 (PORT 4):
3.0 Gb/s data transfer rate.
see
p.14, No. 5)
(SATA_3 (PORT 5):
see
p.14, No. 6)
Serial ATA (SATA)
Either end of the SATA data
Data Cable
cable can be connected to the
(Optional)
SATA / SATA2 hard disk or the
SATA2 connector on this
motherboard.
SATA_0 (PORT 0)
SATA_2 (PORT 4)
SATA_1 (PORT 1)
SATA_3 (PORT 5)
USB 2.0 Headers
Besides four default USB 2.0
(9-pin USB4_5)
ports on the I/O panel, there
(see p.14
No. 7)
are two USB 2.0 headers on
this motherboard. Each
USB 2.0 header can support
two USB 2.0 ports.
(9-pin USB6_7)
(see p.14
No. 8)
Consumer Infrared Module Header
This header can be used to
(4-pin CIR1)
connect the remote
(see
p.14
No. 9)
controller receiver.