Acer AL711 User Guide
Acer AL711 Manual
 |
View all Acer AL711 manuals
Add to My Manuals
Save this manual to your list of manuals |
Acer AL711 manual content summary:
- Acer AL711 | User Guide - Page 1
Monitor and Swivel Base 2 Introduction...3 Installation...3 User Controls...4 OSD Function Description...4 OSD Icon Summary...5 Specification...5 Troubleshooting...7 Important Safety Instructions 1. Please read these instructions thoroughly. 2. Please keep this guide a qualified service center: a- - Acer AL711 | User Guide - Page 2
, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, du Règlement sur le matériel brouilleur du Canada. Connecting the Monitor and Swivel Base 1. Place the monitor with its tube down on a stable surface. 2. Align the four - Acer AL711 | User Guide - Page 3
following items are in the packing it was shipped in, and found in good working condition: n 17" Monitor n Tilt and Swivel Base n Power Cord n This User's manual Please contact your dealer or nearest service centers if any of the above items is missing or damaged. Installation 1. Connect the - Acer AL711 | User Guide - Page 4
User Controls 1. Power Switch Turns the monitor on 2. Power LED Indicator LED color Status Green On Amber Sleep 3. Select Button • Launches On -Screen Display • Make sure the select functions or adjustments • Exit menus and On-Screen Display 4. Backward and Forward Buttons • Backward button - Acer AL711 | User Guide - Page 5
-clockwise Color Temp. Adjusts the warmth of the displayed colors Reset Resets to default values Degauss Demagnetizes the screen to reduce color impurities Exit Exits the OSD menu Specification Screen Size Dot Pitch (mm) Surface Viewable Image Area 17" CRT 0.27 Non -glare 16.14" (41.0 cm - Acer AL711 | User Guide - Page 6
Packed in box 16.8 Kgs (37.04 lbs) 6 - Acer AL711 | User Guide - Page 7
Troubleshooting Please refer to the following solutions for the failure symptoms that occur the most frequent. If the symptom remains after trying these suggested solutions, please contact your local authorized service center. Problem: Power LED is not lit when monitor is powered on. @ Check to make
-
1 -
2 -
3 -
4 -
5 -
6 -
7
 |
 |
1
Table of Contents
Important Safety Instructions
.......................................................................................................
1
Federal Communications Commission
........................................................................................
4
Connecting the Monitor and Swivel Base
....................................................................................
2
Removing the Monitor and Swivel Base
......................................................................................
2
Introduction
....................................................................................................................................
3
Installation
......................................................................................................................................
3
User Controls
..................................................................................................................................
4
OSD Function Description
............................................................................................................
4
OSD Icon Summary
.......................................................................................................................
5
Specification
....................................................................................................................................
5
Troubleshooting
.............................................................................................................................
7
Important Safety Instructions
1.
Please read these instructions thoroughly.
2.
Please keep this guide for future use.
3.
Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol
sprays to clean this device. Use a clean dampened cloth in stead.
4.
To avoid damaging the device, only use factory-approved accessories.
5.
Protect the device against moisture.
6.
In order to set up the device, first place it on a stable surface. Tipping it over or dropping can harm the
monitor and cause injuries. Please follow the setup instructions of the manufacturer while setting up your
monitor.
7.
The ventilation openings are used for air circulation to protect the device against overheating.
8.
When connecting the device, obey the maximum connected load values of the main power supply.
9.
The wall socket must be equipped with a non-fused grounded conductor contact for electrical safety.
10.
The power cable must be laid in such a way nobody can trip over it. Please do not place any objects on the
cable.
11.
Follow all instructions and warning remarks that are printed on the device.
12.
If the device will not be used for a long period of time, please disconnect it from the main power supply to
avoid power surge damage such as lightning.
13.
Make sure no sharp objects or liquids enter the device via its air circulation openings. This could result in a
fire or an electric shock.
14.
Never open the device casing yourself, there are no user serviceable parts inside. Only authorized technical
service personnel should open the casing of this device.
15.
If any of the following conditions occur, the device must be disconnected from the main supply, and be
checked by a qualified service center:
a-
Power cable or power plug are damaged;
b- Liquid has entered the device;
c- The device was exposed to moisture;
d-
The device does not operate according to the user’s guide, or you do not achieve any improvement with
the aid of this guide;
e-
The device has been dropped and/or the casing is damaged;
f-
The device shows obvious signs of a defect.
16.
Use only approved original spare parts, or parts in accordance with the
original parts, for repairs. The use of
incorrect/unauthorized spare parts may cause further damage.
17.
Please contact your service center for any questions regarding service and repairs to guarantee the device’s
performance and reliability.
18.
The power socket must be installed near the equipment to be easily accessible.