Acer FL8610 User Manual - Page 5

Product servicing, Additional safety information, RG2 IEC 62471-5:20151

Get Acer FL8610 PDF manuals and user guides View all Acer FL8610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

v Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel when: • the power cord or plug is damaged, cut or frayed • liquid was spilled into the product • the product was exposed to rain or water • the product has been dropped or the case has been damaged • the product exhibits a distinct change in performance, indicating a need for service • the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options. Your device and its enhancements may contain small parts. Keep them out of the reach of small children. Additional safety information • Do not look into the lens while the light source is on. The strong light from the light source may cause damage to your eyesight. RG2 IEC 62471-5:20151 • Do not place anything in front of the lens while the projector is operating. Things placed in front of the lens may overheat and burn or start a fire. If you want to temporarily stop the projected image, use the Blank key on the remote control. • Do not remove any screws. Do not block or cover the vents. • Do not look into the lens. (For USA and Canada only). • Laser aperture warning: (For USA and Canada only). • CLASS 3R LASER PRODUCT-AVOID DIRECT EYE EXPOSURE • Do not look into the light source using optical instruments (such as magnifying glasses and mirrors). Visual impairment could result. • When turning on the projector, make sure no one within projection range is

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need
for service
•
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
Do not look into the lens while the light source is on. The strong light from
the light source may cause damage to your eyesight.
RG2 IEC 62471-5:20151
•
Do not place anything in front of the lens while the projector is operating.
Things placed in front of the lens may overheat and burn or start a fire. If
you want to temporarily stop the projected image, use the Blank key on
the remote control.
•
Do not remove any screws. Do not block or cover the vents.
•
Do not look into the lens. (For USA and Canada only).
•
Laser aperture warning: (For USA and Canada only).
•
CLASS 3R LASER PRODUCT-AVOID DIRECT EYE EXPOSURE
•
Do not look into the light source using optical instruments (such as magnifying
glasses and mirrors). Visual impairment could result.
•
When turning on the projector, make sure no one within projection range is