Acer P5530i User Manual - Page 51

OSD Messages, Problems with the Projector, Condition, Message Reminder, Solution

Get Acer P5530i PDF manuals and user guides View all Acer P5530i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

English 41 OSD Messages # Condition 1 Message Message Reminder • Fan Fail - the system fan is not working. Fan Fail. Lamp will automatically turn off soon. • Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message. Projector overheated, system will turn off automatically soon, please: 1. Check if operation ambient temperature between 5 degree and 40 degree. 2. Check if filter needs to be cleaned. 3. Check if inlet or outlet is blocked. 4. Check if high altitude mode is set when the projector operating at high altitude area. • Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon. Lamp is approaching the end of its useful life in full power Replacement suggested! Problems with the Projector # Condition Solution 1 The projector stops responding If possible, turn off the projector, then to all controls unplug the power cord and wait at least 30 seconds before reconnecting power. 2 Lamp burns out or makes a popping sound When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
41
English
OSD Messages
Problems with the Projector
#
Condition
Message Reminder
1
Message
•
Fan Fail - the system fan is not working.
•
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed
to cool down before it may be used. Please check the
following message.
•
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
Fan Fail.
Lamp will automatically turn off soon.
Projector overheated, system will turn off automatically soon, please:
1. Check if operation ambient temperature between 5 degree and 40 degree.
2. Check if filter needs to be cleaned.
3. Check if inlet or outlet is blocked.
4. Check if high altitude mode is set when the projector operating at high altitude area.
Lamp is approaching the end of its useful life in full power
Replacement suggested!