American Standard 3073.216.020 Installation Instructions
American Standard 3073.216.020 - 3073.216.020 FloWise Dual Flush Right Height Elongated High Efficiency Toilet Bowl Manual
 |
UPC - 033056710333
View all American Standard 3073.216.020 manuals
Add to My Manuals
Save this manual to your list of manuals |
American Standard 3073.216.020 manual content summary:
- American Standard 3073.216.020 | Installation Instructions - Page 1
USE INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE FloWise™ DUAL FLUSH 2-PIECE TOILET Normal Height, Elongated Rim: 2479 / 2476 / 2779 Right Height™ Elongated Rim: 2480 / 2484 / 2778 / 2566 Certified by Normal Height, Round Front: 2489 IAPMO R&T Thank you for selecting American Standard - the - American Standard 3073.216.020 | Installation Instructions - Page 2
SEAT Install toilet seat in accordance with manufacturer's directions. 9a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these - American Standard 3073.216.020 | Installation Instructions - Page 3
PARTS part is used as this fill valve varies from the standard cleaning your toilet, wash American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). REPAIR PARTS LIST Repair parts are determined by toilet - American Standard 3073.216.020 | Installation Instructions - Page 4
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. PROBLEM Does not flush Poor or sluggish flush Toilet leaks Toilet does not shut off TROUBLESHOOTING GUIDE necessary. d. Normal supply pressure must be at least 20 psi. a. Review Step 9 of installation procedure.
-
1 -
2 -
3 -
4
 |
 |
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
S
A
V
E
F
O
R
F
U
T
U
R
E
U
S
E
7301144-100 Rev. H
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE:
Pictures may not exactly define contour of china and components.
Normal Height, Elongated Rim: 2479 / 2476 / 2779
Right Height™ Elongated Rim: 2480 / 2484 / 2778 / 2566
Normal Height, Round Front: 2489
FloWise™ DUAL FLUSH 2-PIECE TOILET
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CLOSET
FLANGE
CLOSET
BOLTS
A
WAX RING
SEALANT
5
4
3
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
BOLT
CAP
FLANGE
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152mm) apart and parallel to wall.
TEMPORARILY set toilet in place.
Place tapered washer and nuts onto
the bolts as shown in Step 5. Mark bolt
length needed for bolt cap clearance.
Remove toilet.
Precut the bolts to
length by twisting the nut onto the bolt
past the cut mark, then cutting the bolt
to the desired length with a hacksaw.
Unscrew the nut to repair the threads.
Re-install bolts in flange.
!
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line.
NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
2
1
ROUGHING-IN DIMENSIONS:
FINISHED WALL
C/L
FINISHED FLOOR
SUPPLY
AS
REQUIRED
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2009
REMOVE OLD TOILET
Certified by
IAPMO R&T
A
MODELS:
DIMENSION A:
2479
2476
2779
2480
2484
2778
2566
2489
12"
(305 mm)