American Standard 3264.016.222 Installation Instructions
American Standard 3264.016.222 - 3264.016.222 Standard Collection Elongated Toilet Bowl Manual
 |
UPC - 033056558690
View all American Standard 3264.016.222 manuals
Add to My Manuals
Save this manual to your list of manuals |
American Standard 3264.016.222 manual content summary:
- American Standard 3264.016.222 | Installation Instructions - Page 1
Toilet " THE " C O L L E C T I O N™ by Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions from base area. NOTE: Mounting surface must be clean and level before new toilet is - American Standard 3264.016.222 | Installation Instructions - Page 2
SEAT Install toilet seat in accordance with manufacturer's directions. 9a 9b Before continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal - American Standard 3264.016.222 | Installation Instructions - Page 3
damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked - American Standard 3264.016.222 | Installation Instructions - Page 4
of this American Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model. This warranty does not apply to local building code compliance
-
1 -
2 -
3 -
4
 |
 |
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely.
Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line.
NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
, and slide
into place 6" (152 mm) apart and parallel to wall.
3
2
CLOSET FLANGE
CLOSET BOLTS
730517-100
A
CAUTION:
PRODUCT IS FRAGILE.
TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
!
NOTE:
Pictures may not exactly define contour of china and components.
ROUGHING-IN DIMENSIONS:
Thank you
for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
INSTALLATION INSTRUCTIONS
Model 2474 Elongated Two Piece Toilet
WAX RING
SEALANT
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet.
Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
C/L OF SUPPLY
AS REQUIRED
FINISHED
FLOOR
12"
(305mm)
FINISHED WALL
by
COLLECTION
™
“
”
THE
SAVE FOR FUTURE USE