Asko D5636XLHS/TH Use and Care Guide EN - Page 9
If the dishwasher is turned off using
View all Asko D5636XLHS/TH manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
You can vary the temperature as shown below: Sanitation: 150 °F (65 °C) / 160 °F (70 °C) Normal: 124 °F (51 °C) / 150 °F (65 °C) Heavy: 140 °F (60 °C)/150 °F (65 °C) Quick: 85 °F (30 °C) / 140 °F (60 °C) Delicate: 105 °F (40 °C) / 120 °F (50 °C) Eco: 130 °F (55 °C) / 140 °F (60 °C) Upper half: 130 °F (55 °C) / 150 °F (65 °C) Lower half: 130 °F (55 °C) / 150 °F (65 °C) Long dry Activate Long dry to increase final rinse temperature and dry time to improve drying results. This causes a slight increase in energy consumption. This option can be used with all programs except Rinse & Hold. If you want a program with Short dry, press again so that the field under the button turns off. Delayed start When you select Delayed start, the dishwasher will start 1-24 hours after you press the Start/Stop button. 1 Press the button once to activate Delayed start. Press the button several times - or hold it in - to set the desired number of hours. 2 Press Start/Stop and the dishwasher counts down 1 hour at a time and starts after the selected delay. Press and hold Start/Stop for three seconds if you want to cancel the Delayed start option. NOTE! Remember to press the Start/Stop button to start the program. Start the dishwasher Press and hold Start/Stop until the display shows (the door open symbol). This indicates that the dishwasher is ready to start. Close the door properly, otherwise the dishwasher will not start. The display flashes three times with the remaining time to indicate that the program has started. NOTE! If the machine does not start within 2 minutes of the last button press, the display returns to showing the last program run. Time remaining Once you have selected a program and options, the display indicates how long the program took the last time it was used. Once you have started the dishwasher, the display indicates how much program time remains. The remaining time is updated after the water for the final rinse has been heated. This may differ somewhat from time to time depending on the temperature of the water supply, the amount of dishes, the ambient temperature, and other factors. The time counts down while the program is running and the remainder of the program is displayed. The remaining time is displayed, e.g., 1:15, meaning that 1 minute 15 seconds of the program remains. NOTE! During the first run of each program, the remaining time displayed can be slightly misleading, as the dishwasher is estimating the time. When you run the program a second time, the dishwasher will calculate the remaining time based on the previous duration of the program. Stopping or changing a program If you want to change programs after starting the dishwasher, open the door then press and hold Start/Stop for three seconds. Add more detergent if the lid of the detergent dispenser has opened. Then choose a new program, press Start/Stop, and close the door. Do you want to add more dishes? Open the door. The dishwasher stops automatically. Add the dishes, close the door, and the dishwasher resumes the program. If the dishwasher is turned off using the On/Left-on mode button or due to a power failure If the program was not finished, the interrupted program resumes when power is restored. NOTE! During drying, the program is interrupted if the power is cut or the door is open for more than 2 minutes. Once the program has finished Once the program has finished, "End" appears on the display. At the end of the program, one short signal will sound. Chapter Settings describes how to change this function. Once the cycle is complete, the dishwasher uses standby power only. 9