Asus M2N-X PLUS User Manual - Page 36

IDE connector 40-1 pin PRI_IDE

Get Asus M2N-X PLUS PDF manuals and user guides View all Asus M2N-X PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2. IDE connector (40-1 pin PRI_IDE) The onboard IDE connector is for Ultra DMA 133 / 100 / 66 / 33 signal cable. There are three connectors on each Ultra DMA 133 / 100 / 66 / 33 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). Drive jumper setting Single device Cable-Select or Master Two devices Cable-Select Master Slave Mode of device(s) Cable connector - Black Master Black Slave Gray Master Black or gray Slave • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133 / 100 / 66 / 33 IDE devices. If any device jumper is set as "Cable-Select", ensure that all other device jumpers have the same setting. R M2N-X PLUS PRI_IDE PIN1 NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1. M2N-X PLUS IDE Connector 1-24 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
1-24
Chapter 1: Product introduction
2.
IDE connector (40-1 pin PRI_IDE)
The onboard IDE connector is for Ultra DMA 133 / 100 / 66 / 33 signal cable.
There are three connectors on each Ultra DMA 133 / 100 / 66 / 33 signal
cable: blue, black, and gray. Connect the blue connector to the motherboard’s
IDE connector, then select one of the following modes to configure your
device(s).
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133 / 100 / 66 / 33 IDE
devices.
If any device jumper is set as “Cable-Select”, ensure that all other device
jumpers have the same setting.
Black or gray
Drive jumper
Mode
Cable
setting
of device(s)
connector
Single device
Cable-Select or Master
-
Black
Two devices
Cable-Select
Master
Black
Slave
Gray
Master
Master
Slave
Slave
M2N-X PLUS IDE Connector
NOTE:
Orient the red markings
(usually zigzag) on the ID
ribbon cable to PIN 1.
PRI_IDE
PIN1
M2N-X PLUS