Asus P2V-B P2V-B User Manual - Page 31

Enabled, Power Management Setup

Get Asus P2V-B PDF manuals and user guides View all Asus P2V-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

GND +12V Rotation III. H/W SETUP Connectors III. HARDWARE SETUP 7. Chassis,CPU,&Power SupplyFanConnectors(3-pinCHA_,CPU_,PWR_FAN) These connectors support 12-Volt cooling fans of 500mA (6 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the this connector. NOTE: The "Rotation" signal should be used only with a specially designed fan with rotation signal. WARNING! These connectors have power. Damage may occur to the motherboard and/or the CPU fan if these connectors are incorrectly used. CPU Fan Power P2V-B R Power Supply Fan GND +12V Rotation Chassis Fan Power GND +12V Rotation P2V-B Fan Connectors 8. Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101. The LAN card powers up the system when a wakeup packet or signal is received from the network. IMPORTANT: This feature requires that the WAKE On LAN Power Up Control is set to Enabled (see Power Management Setup under BIOS SETUP) and that your system has an ATX power supply with at least 720mA +5V standby power. P2V-B R WOL_CON Ground +5 VSB PME P2V-B Wake-On-LAN Connector ASUS P2V-B User's Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
ASUS P2V-B User’s Manual
31
III. HARDWARE SETUP
7.
Chassis, CPU , & Power Supply Fan Connectors (3-pin CHA_, CPU_, PWR_FAN)
These connectors support 12-Volt cooling fans of 500mA (6 Watts) or less.
Ori-
entate the fans so that the heat sink fins allow airflow to go across the onboard
heat sink(s) instead of the expansion slots.
Depending on the fan manufacturer,
the wiring and plug may be different.
The red wire should be positive, while the
black should be ground.
Connect the fan’s plug to the board taking into consid-
eration the polarity of the this connector.
NOTE:
The “Rotation” signal should
be used only with a specially designed fan with rotation signal.
WARNING!
These connectors have power. Damage may occur to the mother-
board and/or the CPU fan if these connectors are incorrectly used.
P2V-B Fan Connectors
Chassis Fan Power
GND
Rotation
+12V
Power Supply Fan
CPU Fan Power
GND
Rotation
+12V
GND
Rotation
+12V
P2V-B
8.
Wake-On-LAN Connector (3-pin WOL_CON)
This connector connects to a LAN card with a Wake-On-LAN output, such as
the ASUS PCI-L101. The LAN card powers up the system when a wakeup
packet or signal is received from the network.
IMPORTANT:
This feature requires that the
WAKE On LAN
Power Up Con-
trol
is set to
Enabled
(see
Power Management Setup
under BIOS SETUP
)
and
that your system has an ATX power supply with at least 720mA +5V standby
power.
P2V-B Wake-On-LAN Connector
+5 VSB
PME
Ground
P2V-B
WOL_CON
Connectors
III.
H/W SETUP