Asus P5B-Plus Vista P5B-Plus user's manual - Page 54
ICH8R Serial ATA connectors 7-pin SATA1 [red], SATA2 [red], SATA3, black], SATA4 [black], SATA5 [red
View all Asus P5B-Plus Vista manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 54 highlights
3. ICH8R Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black], SATA5 [red], SATA6 [red]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 5, RAID 10 configuration with the Intel® Matrix Storage Technology through the onboard Intel® ICH8R RAID controller. • These connectors are set to Standard IDE mode by default. In Standard IDE mode, you can connect Serial ATA boot/data hard disk drives to these connectors. If you intend to create a Serial ATA RAID set using these connectors, set the Configure SATA as item in the BIOS to [RAID]. See section 4.3.5 IDE Configuration for details. • For RAID 5, use at least three hard disk drives. For RAID 10, use at least four hard disk drives. Use two to four Serial ATA hard disk drives for each RAID 0 or RAID 1 set. SATA1 SATA2 SATA3 SATA1 SATA2 SATA3 RRGSSNAARGDTTSNAA__ADTRRAXX_PN11RXN1 GNRDSATA_RXP1 RRGSSNAARRGDTTSSNAA__AADTTTTXXAAPN__11TTXXPN11 GND GND RSATA_RXN2 RSATA_RXP2 GNGDND RRGSSNAARRGDTTSSNAA__AADTTTTXXAAPN__22RRXXPN22 RSATA_TXN2 RSATA_TXP2 GND GND RSATA_RXN3 RSATA_RXP3 GND RSATA_TXN3 RGSNARGDTSNA_ADTTXAP_3RXN3 RSATA_RXP3 GND RSATA_TXN3 RSATA_TXP3 GND ® P5B-PLUS ® P5B-PLUS SSAATTAA66 SASTAA5TA5SATAS4ATA4 RGSNADTRRGASSN_AADTTRAAX__RRN6XXPN66 RSATGAN_DRXP6 RRGSSNAADTTRRGAASSN__AADTTTTAAXX__PNTT66XXPN66 GND GND RSATA_RXN5 RSATA_RXP5 GNDGND RRGSSNAADTTRRGAASSN__AADTTRRAAXX__TTPNXX55PN55 RSATA_TXN5 RSATA_TXP5 GND GND RSATA_RXN4 RSATA_RXP4 GND RSATA_TXN4 RGSNADTRGASN_ADTRAX_TNX4P4 RSATA_RXP4 GND RSATA_TXN4 RSATA_TXP4 GND P5B-PLUS SATA connectors P5B-PLUS SATA connectors • You must install Windows® 2000 Service Pack 4 or the Windows® XP Service Pack 1 before using Serial ATA hard disk drives. The Serial ATA RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is available only if you are using Windows® 2000/XP or later version. • When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1/2/5/6 connector. Refer to the table below for the recommended SATA hard disk drive connections. Serial ATA hard disk drive connection Connector SATA1/2/5/6 Color Red Setting Master SATA3/4 Black Slave Use Boot disk Data Disk 2-28 Chapter 2: Hardware information