Asus V2-P5G33 User Manual - Page 36

Installing a hard disk drive

Get Asus V2-P5G33 - V Series - 0 MB RAM PDF manuals and user guides
UPC - 610839743810
View all Asus V2-P5G33 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

7. Connect the other end of the IDE ribbon cable to the secondary IDE connector (labeled SEC_IDE) on the motherboard. See page 4-7 for the location of this connector. 8. Remove the dummy drive slot cover from the front panel. 9. Replace the front panel. 2.8 Installing a hard disk drive To install a Serial ATA hard disk drive: 1. Carefully place the hard disk into the the lowest 3.5-inch drive slot (without the metal plate cover). 2. Fasten the screws to secure the hard disk to the drive slot. the lowest 3.5inch drive slot without the metal plate cover If you do not need to install the optional card reader into your system, you can install the HDD in the one of the 3.5-inch external bay (with the metal plate cover). 3. Connect one end of the Serial ATA cable to the SATA connector at the back of the drive, then connect the other end to a Serial ATA connector on the motherboard. See page 4-6 for the location of the Serial ATA connectors. 2-18 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
2-18
Chapter 2: Basic installation
7.
Connect the other end of the IDE ribbon cable to the secondary IDE
connector (labeled SEC_IDE) on the motherboard. See page 4-7 for
the location of this connector.
8.
Remove the dummy drive slot cover from the front panel.
9.
Replace the front panel.
2.8
Installing a hard disk drive
To install a Serial ATA hard disk drive:
1.
Carefully place the hard disk into the the lowest 3.5-inch drive slot
(without the metal plate cover).
2.
Fasten the screws to secure the hard disk to the drive slot.
the lowest 3.5-
inch drive slot
without the metal
plate cover
3.
Connect one end of the Serial ATA cable to the SATA connector at
the back of the drive, then connect the other end to a Serial ATA
connector on the motherboard. See page 4-6 for the location of the
Serial ATA connectors.
If you do not need to install the optional card reader into your system,
you can install the HDD in the one of the 3.5-inch external bay (with the
metal plate cover).