Behringer ACX900 Manual - Page 8
Sound Processing
View all Behringer ACX900 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
ULTRACOUSTIC ACX450/ACX900/ACX1800 4. SOUND PROCESSING s Use the FX LEVEL controller audible. to make the effect The ULTRACOUSTIC offers many options for sound processing. The ACX1800 includes, for example, an FBQ equalizer, a multieffects unit and a compressor. The various processing options are explained in this chapter. s Edit the effect using the PARAMETER controller (only in ACX1800). 4.1 FBQ equalizer A graphic equalizer with FBQ spectrum analyzer is available for sound adjustment and correction. If the sliding controllers are in neutral position (0), the signal is not modified. s To boost the frequency range, move the respective sliding controller up. s To dampen the range, move the sliding controller down. s Press the FBQ switch to activate the FBQ display. FBQ function: Each controller is equipped with a LED indicating the level of the associated frequency range of the controller by means of its brightness. This assists you in identifying the controller that must be used to edit the sound. If the sound is for example too dull or too droning, one of the LEDs is probably very bright, indicating the sliding controller that should be moved down to reduce the bass level. On the other hand, you can quickly identify frequency ranges whose level is too low (LED barely lit) to increase it. + To emphasize certain frequency ranges, it might not be necessary to raise these, but to lower the levels of the other frequencies by moving the respective sliding controllers down. This approach prevents excessively high internal signal levels, thus retaining valuable dynamic reserves (headroom). 4.2 Digital effects processor One of the key features of your ULTRACOUSTIC are the two built-in multi-effects processors that operate independently of each other in both channels. Each effects module offers a total of 16 different programs that are grouped in four categories. s To switch effects on or off, press the IN/OUT switch at the ULTRACOUSTIC or at the foot switch. s Turn the FX SELECT controller to select a program. The effects are described in the following overview: AY AYÃ t h 5(9(5% 02' 02''/< '(/$< Apv Chamber Room Hall Concert Chorus Flanger Phaser Tremolo Chorus / Delay 400 ms Flanger / Delay 400 ms Chorus / Delay 300 ms Flanger / Delay 300 ms Delay 80 ms Delay 300 ms Delay 400 ms Delay 500 ms Qh hrr 68Y ' Decay Decay Decay Decay Depth Depth Speed Speed Delay Level Delay Level Delay Level Delay Level Feedback Feedback Feedback Feedback Table 4.1: Effects programs The reverb presets are effects that imitate the reverberation of various large rooms. Use the PARAMETER controller to adjust the reverberation time (decay). 1 CHAMBER simulates the typical characteristics of a studio. This effect is useful in cases where you need unobtrusive reverb to liven up the signal. 2 ROOM: Reverberation typical for rooms of medium size, with clearly audible reverb from walls. 3 HALL: Simulation of a lively large hall with considerable echo. 4 CONCERT simulates the prolonged reverb in a large concert hall. This group includes four modulation effects that are generated in different ways. For each effect, you can adjust the depth and speed of the modulation. 5 CHORUS give guitar signals more depth and width. This is achieved by means of a modulated delay of the input signal. 6 FLANGER: Popular guitar effect achieved by constant modulation of the tone pitch. 7 PHASER: The phase effect is similar to the flange, but somewhat subtler. It is achieved by superimposing a phase-shifted effects signal on the input signal. 8 TREMOLO: Intensive variation of the volume at a preset rate. This group includes a number of dual effects where for example a chorus or flanger effect is combined with a delay. In the ACX1800, you can adjust the volume of the delay effect. 9 CHORUS/DELAY with a delay of 400 ms. 10 FLANGER/DELAY with a long delay (400 ms) 11 CHORUS/DELAY with a short delay (300 ms). 12 FLANGER/DELAY with a delay of 300 ms. In this group you find delay effects with different delay times. The Feedback parameter determines the number of repeats. 13 Short DELAY of 80 milliseconds (ms). 14 Medium DELAY of 300 ms. 15 DELAY of 400 ms. 16 Long DELAY of 500 ms. 8 4. SOUND PROCESSING