BenQ MX503 MS502, MX503 User Manual - Page 33

Shutting down the projector, Direct power off, Power On/Off Ring Tone

Get BenQ MX503 PDF manuals and user guides View all BenQ MX503 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

2. Press to highlight Volume and press / to select a desired sound level. Turning off the Power On/Off Ring Tone To turn off the ring tone: 1. Repeat steps 1-2 above. 2. Press to highlight Power On/Off Ring Tone and press / to select Off. The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone. Shutting down the projector 1. Press POWER and a confirmation message will display prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. To protect the lamp, the projector will not respond to any commands during the cooling process. To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 39 for details. 3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop. Disconnect the power cord from the power outlet. • To turn off the power ring tone, see "Turning off the Power On/ Off Ring Tone" on page 33 for details. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange. • Lamp life results will vary depending on environmental conditions and usage. Direct power off The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press II POWER again to start the projector after the fans stop and the POWER indicator light turns orange. Operation 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Operation
33
2.
Press
to highlight
Volume
and press
/
to select a desired sound level.
Turning off the
Power On/Off Ring Tone
To turn off the ring tone:
1.
Repeat steps 1-2 above.
2.
Press
to highlight
Power On/Off Ring Tone
and press
/
to select
Off
.
The only way to change
Power On/Off Ring Tone
is setting On or Off here. Setting the sound mute or
changing the sound level will not affect the
Power On/Off Ring Tone
.
Shutting down the projector
1.
Press
POWER
and a confirmation message will display prompting you.
If you don't respond in a few seconds, the message will disappear.
2.
Press
POWER
a second time. The
POWER indicator light
flashes orange,
the projection lamp shuts down, and the fans will continue to run for approximately
90 seconds to cool down the projector.
To protect the lamp, the projector will not respond to any commands during the cooling process.
To shorten the cooling time, you can also activate the Quick cooling function. See
"Quick Cooling" on page 39
for details.
3.
Once the cooling process finishes, a "
Power Off
Ring Tone
" will be heard. The
POWER indicator
light
is a steady orange and fans stop. Disconnect
the power cord from the power outlet.
•
To turn off the power ring tone, see
"Turning off the Power On/
Off Ring Tone" on page 33
for details.
•
If the projector is not properly shut down, to protect the lamp,
when you attempt to re-start the projector, the fans will run for a
few minutes to cool down. Press
POWER
again to start the
projector after the fans stop and the
POWER indicator light
turns orange.
•
Lamp life results will vary depending on environmental conditions
and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect
the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to
re-start the projector, the fans may run for a few minutes to cool down. In such cases,
press
POWER again to start the projector after the fans stop and the POWER indicator
light turns orange.
I
I