BenQ MX511 DLP Projector User Manual - Page 42

Personalizing the projector menu display, Shutting down the projector

Get BenQ MX511 DLP Projector PDF manuals and user guides View all BenQ MX511 DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Menu position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. • Reminder Message in the SYSTEM SETUP: Basic > Menu Settings menu sets whether to display reminder messages on screen. Use / to select your desired setting. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Shutting down the projector 1. Press II Power and a confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press II Power a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. • To protect the lamp, the projector will not respond to any commands during the cooling process. • To shorten the cooling time, you can also activate the Quick Cooling function. See "Quick Cooling" on page 45 for details. 3. Once the cooling process finishes, the POWER indicator light is a steady orange and fans stop. 4. Disconnect the power cord from the power putlet if the projector will not be used in an extended period of time. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the POWER indicator light turns orange. • Actual lamp life may vary due to different environmental conditions and usage. 42 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Operation
42
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets the length
of time the OSD will remain active after your last key press. The time length ranges from
5 to 30 seconds in 5-second increments. Use
/
to select a suitable time frame.
•
Menu position
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets the OSD
position in five locations. Use
/
to select a preferred position.
•
Language
in the
SYSTEM SETUP: Basic
menu sets your familiar language for the OSD
menus. Use
/
to select your language.
•
Reminder Message
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets whether to
display reminder messages on screen. Use
/
to select your desired setting.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen to be
displayed during projector start-up. Use
/
to select a screen.
Shutting down the projector
1.
Press
Power
and a confirmation message
displays prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
Press
Power
a second time. The
POWER
indicator light
flashes orange, the projection
lamp shuts down, and the fans will continue to
run for approximately 90 seconds to cool down
the projector.
•
To protect the lamp, the projector will not respond
to any commands during the cooling process.
•
To shorten the cooling time, you can also activate
the Quick Cooling function. See
"Quick Cooling"
on page 45
for details.
3.
Once the cooling process finishes, the
POWER
indicator light
is a steady orange and fans stop.
4.
Disconnect the power cord from the power putlet if the projector will not be used in
an extended period of time.
•
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
the projector, the fans will run for a few minutes to cool down. Press Power again to start
the projector after the fans stop and the POWER indicator light turns orange.
•
Actual lamp life may vary due to different environmental conditions and usage.
I
I
I
I