Biostar IDEQ 220K BIOS MANUAL
Biostar IDEQ 220K Manual
 |
View all Biostar IDEQ 220K manuals
Add to My Manuals
Save this manual to your list of manuals |
Biostar IDEQ 220K manual content summary:
- Biostar IDEQ 220K | BIOS MANUAL - Page 1
K8VBK-S7 BIOS Setup BIOS Setup 1 1 Main Menu 3 2 Standard CMOS Features 6 3 Advanced BIOS Features 9 4 Advanced Chipset Features 16 5 Integrated Peripherals 22 6 Power Management Setup 29 7 PnP/PCI Configurations 35 8 PC Health Status 38 9Voltage Control 40 i - Biostar IDEQ 220K | BIOS MANUAL - Page 2
fine-tuning of the chipset controlling the entire system. The rest of this manual is intended to guide you through the process of configuring your system using Setup. Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1.0A specification. ESCD (Extended System Configuration - Biostar IDEQ 220K | BIOS MANUAL - Page 3
Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR SDRAM (Double Data Rate Synchronous DRAM) are supported. Supported CPUs This AWARD BIOS supports the AMD CPU. Using Setup In general, you use the arrow keys to highlight items, press - Biostar IDEQ 220K | BIOS MANUAL - Page 4
WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update features of the BIOS. Advanced Chipset Features This submenu allows you to configure special chipset features. Integrated Peripherals - Biostar IDEQ 220K | BIOS MANUAL - Page 5
K8VBK-S7 BIOS Setup Power Management Setup This submenu allows you to configure the power management features. PnP/PCI Configurations This may cause the CPU or M/B damage!) Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the - Biostar IDEQ 220K | BIOS MANUAL - Page 6
K8VBK-S7 BIOS Setup Set User Password If the Supervisor Password is not set, then but will not be able to change them. Save & Exit Setup Save all configuration changes to CMOS(memory) and exit setup. Confirmation message will be displayed before proceeding. Exit Without Saving Abandon all changes - Biostar IDEQ 220K | BIOS MANUAL - Page 7
K8VBK-S7 BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one - Biostar IDEQ 220K | BIOS MANUAL - Page 8
K8VBK-S7 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Description Date mm : dd : yy Set - Biostar IDEQ 220K | BIOS MANUAL - Page 9
, but Diskette All, but Disk/ Key N/A N/A N/A Description Select the situation in which you want the BIOS to stop the POST process and notify you. Displays the amount of conventional memory detected during boot up. Displays the amount of extended memory detected during boot up. Displays the total - Biostar IDEQ 220K | BIOS MANUAL - Page 10
K8VBK-S7 BIOS Setup 3 Advanced BIOS Features ! Figure 3. Advanced BIOS Setup 3.1 Boot Seq & Floppy Setup 9 - Biostar IDEQ 220K | BIOS MANUAL - Page 11
K8VBK-S7 BIOS Setup 3.1.1 Hard Disk Boot Priority These BIOS attempt to load the operating system from the device in the sequence selected in these items. The Choices: Pri. Master, Pri.Slave, Sec.Master, Sec. Slave, USBHDD0, USBHDD1, USBHDD2 and Bootable Add-in Carde. 10 - Biostar IDEQ 220K | BIOS MANUAL - Page 12
Setup 3.1.2 First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items. The Choices: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, - Biostar IDEQ 220K | BIOS MANUAL - Page 13
K8VBK-S7 BIOS Setup 3.2 Shadow Setup This item allows you to setup cache & shadow setup. Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution. Enabled (default) Optional ROM is enabled. Disabled Optional ROM is disabled.. 12 - Biostar IDEQ 220K | BIOS MANUAL - Page 14
K8VBK-S7 BIOS Setup 3.3 Cache Setup 3.3.1 CPU Internal Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. 3.3.2 External Cache This option enables or disables "Level 2" - Biostar IDEQ 220K | BIOS MANUAL - Page 15
enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound an alarm beep. Disabled Normal POST. 3.6 Boot Up NumLock Status Selects the NumLock. State after power on. On (default) Numpad is number keys. Off Numpad is arrow - Biostar IDEQ 220K | BIOS MANUAL - Page 16
the operating system. The Choices: Enabled (default), Disabled. 3.12 MPS VERSION CONTROL FOR OS The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification. Select version supported by the operation system running on this computer. The Choices: 1.4 (default), 1.1. 3.13 OS SELECT - Biostar IDEQ 220K | BIOS MANUAL - Page 17
K8VBK-S7 BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default - Biostar IDEQ 220K | BIOS MANUAL - Page 18
2.0 Mode This item allows you to select the AGP Mode. The Choices: 4X (default), 2X, 1X. 4.1.3 AGP Driving Control By choosing "Auto" the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card. By choosing "Manual", it allows user to set AGP output Buffer Drive strength P Ctrl by - Biostar IDEQ 220K | BIOS MANUAL - Page 19
K8VBK-S7 BIOS Setup 4.1.5 AGP Fast Write The Choices: Enabled, Disabled (default). 4.1.6 AGP Master 1 WS Write When Enabled, writes to the AGP (Accelerated Graphics Port) are executed with - Biostar IDEQ 220K | BIOS MANUAL - Page 20
K8VBK-S7 BIOS Setup 4.2 DRAM CONFIGURATION 4.2.1 4.2.2 Max Memclock (MHz) Places an artifical memory clock limit on the system. Memory is prevented from running faster than this frequency. The Choices: 200 (Default), 166, 133, and 100. CAS# Latency This field specify the cas# latency, i.e. cas# - Biostar IDEQ 220K | BIOS MANUAL - Page 21
K8VBK-S7 BIOS Setup 4.3 LDT & PCI BUS CONTROL If you highlight the literal "Press Enter" 4.3.8 PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification. The Choices: Disabled ( - Biostar IDEQ 220K | BIOS MANUAL - Page 22
K8VBK-S7 BIOS Setup 4.4 MEMORY HOLE You can reserve this area of system memory for ISA adapter ROM. When this area is reserved it cannot be cached. The user information of peripherals that need to use this area of system memory usually2 discussed their memory requirements. The Choices: Disabled ( - Biostar IDEQ 220K | BIOS MANUAL - Page 23
K8VBK-S7 BIOS Setup 5 Integrated Peripherals ! Figure 5. Integrated Peripherals 22 - Biostar IDEQ 220K | BIOS MANUAL - Page 24
: 5.1.1 OnChip SATA This option allows you to enable the onchip Serial ATA. The Choices: Enabled (default), Disabled. 5.1.2 IDE DMA Transfer Access The Choices: Enabled (default), Disabled. 5.1.3 On-chip IDE Channel 0/1 The motherboard chipset contains a PCI IDE interface with support for two - Biostar IDEQ 220K | BIOS MANUAL - Page 25
in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. 5.1.7 IDE HDD Block - Biostar IDEQ 220K | BIOS MANUAL - Page 26
K8VBK-S7 BIOS Setup 5.2 VIA OnChip PCI Device If you highlight the literal "Press Enter : Enabled (Default), Disabled. 5.2.4 USB Emulation Support USB legacy、keyboard、Mouse and storage. The Choices: ON (default), OFF. 5.2.5 USB Keyboard/ Mouse Support This item allows you to enable or disable - Biostar IDEQ 220K | BIOS MANUAL - Page 27
K8VBK-S7 BIOS Setup 5.3 Super IO Device 5.3.1 5.3.2 5.3.3 5.3.4 If you highlight the literal "Press Enter" next to the "Super IO Device" label and then press the enter key, it - Biostar IDEQ 220K | BIOS MANUAL - Page 28
K8VBK-S7 BIOS Setup 5.3.5 5.3.6 5.3.7 5.3.8 UR2 Duplex Mode Select the value required by the IR device connected to the IR port. Full-duplex mode permits simultaneous two-direction transmission. - Biostar IDEQ 220K | BIOS MANUAL - Page 29
K8VBK-S7 BIOS Setup 5.4 Onboard 1394 chip This item allows you to enable or disable the Onboard 1394 Chip. The Choices: Enabled (default), Disabled. 5.5 Onboard LAN Device This - Biostar IDEQ 220K | BIOS MANUAL - Page 30
-S7 BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. ! Figure 6. Power Management Setup 6.1 ACPI function This item displays the status of the Advanced Configuration and Power - Biostar IDEQ 220K | BIOS MANUAL - Page 31
K8VBK-S7 BIOS Setup Max. Power Saving Maximum power management only available for sl CPU's. Suspend Mode = 1 min. HDD Power Down = 1 min. User Define (default) Allows you to set each mode individually. When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD Power Down which - Biostar IDEQ 220K | BIOS MANUAL - Page 32
manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard battery (3V). If AC power - Biostar IDEQ 220K | BIOS MANUAL - Page 33
K8VBK-S7 BIOS Setup 6.12 IRQ/Event Activity Detect If you highlight the a VGA Port will awaken a system which has been powered down. The Choices: Off (default), On. 6.12.5 LPT & COM When this option is set to On, any event occurring at a COM (serial)/LPT (printer) port will awaken a system - Biostar IDEQ 220K | BIOS MANUAL - Page 34
-S7 BIOS Setup 6.12.6 HDD & FDD When this option is set to On, any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down. The Choices: On (default), Off. 6.12.7 PCI Master When set to On, you need a LAN add-on card which supports the power function - Biostar IDEQ 220K | BIOS MANUAL - Page 35
K8VBK-S7 BIOS Setup 6.12.13 IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events (i.e. wake on LPT & COMM - Biostar IDEQ 220K | BIOS MANUAL - Page 36
cards used for the boot sequence (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like Window™ 95. When set to NO, BIOS will initialize all the PnP cards. For non-PnP operating systems (DOS, Netware™), this option must set to NO. The Choices: No - Biostar IDEQ 220K | BIOS MANUAL - Page 37
), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral.By Choosing "Manual", the user will bus if the PCI VGA controller responds to the Write. In this case, the PCI VGA controller should not respond to the Write, it should - Biostar IDEQ 220K | BIOS MANUAL - Page 38
K8VBK-S7 BIOS Setup 7.6 Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA. The Choices: Enabled (default), Disabled. 7.7 Assign IRQ For USB This item allows the users to choose which IRQ to assign for the USB. The Choices: Enabled (default), Disabled. 37 - Biostar IDEQ 220K | BIOS MANUAL - Page 39
K8VBK-S7 BIOS Setup 8 PC Health Status ! Figure 8. PC Health Status 8.1 CPU FAN Control The Choice mart? Can make your CPU FAN to Temperature This item allows you to set up the CPU shutdown Temperature. This item only effective under Windows 98 ACPI mode. The Choices: Disabled (default), 60℃/ - Biostar IDEQ 220K | BIOS MANUAL - Page 40
K8VBK-S7 BIOS Setup 8.6 CPU FAN Speed This field displays the current speed of CPU fan. 8.7 SYS FAN Speed This field displays the current speed SYSTEM fan. 8.8 Show H/W Monitor in POST If your computer contains a monitoring system, it will show - Biostar IDEQ 220K | BIOS MANUAL - Page 41
setting. Method 2: Press the key and Power button simultaneously, after that keep-on pressing the key until the power-on screen showed. This action will boot-up the system according to FSB of the processor. It's strongly recommended to set CPU Vcore and clock in default setting. If - Biostar IDEQ 220K | BIOS MANUAL - Page 42
K8VBK-S7 BIOS Setup 12/1/2004 41
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
 |
 |
K8VBK-S7 BIOS Setup
i
BIOS Setup
.......................................................................................
1
1 Main Menu
...................................................................................................
3
2 Standard CMOS Features
.............................................................................
6
3 Advanced BIOS Features
.............................................................................
9
4 Advanced Chipset Features
........................................................................
16
5 Integrated Peripherals
.................................................................................
22
6 Power Management Setup
..........................................................................
29
7 PnP/PCI Configurations
..............................................................................
35
8 PC Health Status
.........................................................................................
38
9Voltage Control
...........................................................................................
40