Biostar K8M800MAM2 K8M800 MICRO AM2 bios guide
Biostar K8M800MAM2 Manual
 |
View all Biostar K8M800MAM2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Biostar K8M800MAM2 manual content summary:
- Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 1
K8M800 Micro AM2 BIOS Setup BIOS Setup ...1 1 Main Menu ...3 2 Standard CMOS Features ...6 4 Advanced Chipset Features 16 5 Integrated Peripherals...23 6 Power Management Setup ...30 7 PnP/PCI Configurations ...36 8 PC Health Status...39 9 Frequency/ Voltage Control 41 i - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 2
K8M800 Micro AM2 BIOS Setup BIOS Setup Introduction This manual discussed Award™ Setup program built into the ROM BIOS. The Setup program of this manual is intended to guide you through the process of configuring your system using Setup. Plug and Play Support These AWARD BIOS supports the Plug - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 3
K8M800 Micro AM2 BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR SDRAM (Double Data Rate Synchronous DRAM) are supported. Supported CPUs This AWARD BIOS supports the AMD CPU. Using - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 4
K8M800 Micro AM2 BIOS Setup 1 Main Menu Once you enter Award BIOS™ CMOS Setup Utility, the Main Menu will sub-menu. !! WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information. „ - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 5
K8M800 Micro AM2 BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE voltage and clock may cause the CPU or M/B damage!) Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence. These - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 6
K8M800 Micro AM2 BIOS Setup Set User Password If the Supervisor Password is not set, will not be able to change them. Save & Exit Setup Save all configuration changes to CMOS(memory) and exit setup. Confirmation message will be displayed before proceeding. Exit Without Saving Abandon all changes - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 7
K8M800 Micro AM2 BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 8
K8M800 Micro AM2 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Description Date mm : dd : yy Set - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 9
K8M800 Micro AM2 BIOS Setup Item Halt On Base Memory Extended Memory Total Memory Options All Errors No Errors All, but Keyboard All, but Diskette All, but Disk/ Key N/A N/A N/A Description Select the situation in which you want the BIOS to stop the POST process and notify you. Displays the - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 10
K8M800 Micro AM2 BIOS Setup 3 Advanced BIOS Features „ Figure 3: Advanced BIOS Setup 9 - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 11
K8M800 Micro AM2 BIOS Setup Boot Seq & Floppy Setup This item allows you to setup boot seq & Floppy. „ Figure 3.1: Boot Seq & Floppy Setup Hard Disk Boot Priority These BIOS attempt to arrange the Hard Disk boot sequence automatically. This will depend on which Hard Disk is installed. „ Figure - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 12
K8M800 Micro AM2 BIOS Setup First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the to setup cache & shadow setup. „ Figure 3.2: Shadow Setup Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution. Enabled (default) - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 13
K8M800 Micro AM2 BIOS Setup Cache Setup „ Figure 3.3: Cache Setup CPU Internal Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. External Cache This option enables or disables " - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 14
K8M800 Micro AM2 BIOS Setup CPU Feature „ Figure 3.4: CPU Feature NPT Fid control This function allows you to adjust the frequency ratio of CPU. The Choices: Auto (default), x4: 800Mhz ~ x25: 5000Mhz (differs from CPU) NPT Vid control This function allows you to adjust the CPU voltage. The Choices: - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 15
K8M800 Micro AM2 BIOS Setup Virus Warning This option allows you to choose the VIRUS Warning feature that is used to protect the IDE Hard Disk boot sector. If this function is enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 16
K8M800 Micro AM2 BIOS Setup APIC Mode Selecting Enabled enables APIC mode reporting from the BIOS to the operating system. The Choices: Enabled (default), Disabled MPS Version Control For OS The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification. Select version supported - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 17
K8M800 Micro AM2 BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 18
K8M800 Micro AM2 BIOS aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the Control By choosing "Auto" the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card. By choosing "Manual", it allows user to set AGP - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 19
K8M800 Micro AM2 BIOS Setup AGP Driving Value While AGP driving control item set to "Manual", it allows user to set AGP driving Trans The Choices: Disabled (default), Auto. VGA Share Memory Size This item allows you to select the VGA share memory size. The Choices: 64M (default), 32M, 16M Disabled. - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 20
K8M800 Micro AM2 BIOS Setup DRAM Configuration „ Figure 4.2: DRAM Configuration Timing Mode This item allows you to choose to manually or automatically regulate the DDR Timing. The Choices: Auto (default), Manual CS. Memory tri-stating The Choices: Disabled (default), Enabled. Memory Hole Remapping - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 21
K8M800 Micro AM2 BIOS Setup DDRII Timing Item The Choices: Disabled (default), Enabled. TwTr Command Delay The Choices: 3 bus clocks (default). TrTfc0 for DIMM0 The Choices: 75ns (default). TrTfc1 - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 22
K8M800 Micro AM2 BIOS Setup LDT & PCI Bus Control If you highlight the literal "Press Enter" next to the "LDT & PCI Bus Control" label and then press the enter - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 23
K8M800 Micro AM2 BIOS Setup PCI1 Post Write When enabled, writes to the PCI bus are buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification. The Choices: Enabled (default), Disabled. Memory Hole You can reserve this area of system memory for ISA - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 24
K8M800 Micro AM2 BIOS Setup 5 Integrated Peripherals „ Figure 5. Integrated Peripheral 23 - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 25
K8M800 Micro AM2 BIOS Setup VIA OnChip IDE Device If you highlight the literal "Press Access. The Choices: Enabled (default), Disabled. OnChip IDE Channel 0/1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels. Select "Enabled" to activate the first and/or second - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 26
in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. IDE HDD Block Mode - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 27
K8M800 Micro AM2 BIOS Setup VIA OnChip PCI Device If you highlight the literal "Press Enter" next to the "VIA OnChip PCI Device" label and then press the enter - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 28
K8M800 Micro AM2 BIOS Setup OnChip USB Controller This option should be enabled if your system Legacy Support. The Choices: On (default), off, KB/ MS. USB Keyboard Support Enables support for USB attached mouse/keyboard. The Choices: Auto (default), Enabled. USB Mouse Support Enables support for USB - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 29
K8M800 Micro AM2 BIOS Setup Super IO Device Press Enter to configure the Super I/O Device. „ Figure 5.3: Super IO Device Onboard FDC Controller Select Enabled if your system has a floppy - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 30
K8M800 Micro AM2 BIOS Setup Parallel Port Mode The default value is SPP. The Choices: SPP (default) Using Parallel Port as Standard Printer Port. EPP Using Parallel Port as - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 31
K8M800 Micro AM2 BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. „ - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 32
K8M800 Micro AM2 BIOS Setup Power Management Option This category allows you to select the type Mode = 1 hr. HDD Power Down = 15 min Max. Power Saving Maximum power management only available for sl CPU's. Suspend Mode = 1 min. HDD Power Down = 1 min. User Define (default) Allows you to set each - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 33
power is restored to a system that had lost power previously without any subsequent manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power Supply (3.3V). While - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 34
K8M800 Micro AM2 BIOS Setup For example: If set to "Former-Sts" and AC power is lost when system is live, then after AC power is restored, the system - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 35
K8M800 Micro AM2 BIOS Setup USB Resume from S3 This item allows you to enable or disabled (default), Off. PCI Master When set to On, you need a LAN add-on card which supports the power function. It should also support the wake-up on LAN jump. The Choices: Off (default), On. PowerOn by PCI Card When - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 36
K8M800 Micro AM2 BIOS Setup IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events (i.e. wake on LPT & COMM activity). „ Figure 6.1.1: - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 37
K8M800 Micro AM2 BIOS Setup 7 PnP/PCI Configurations This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU system like Window™ 95. When set to NO, BIOS will initialize - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 38
K8M800 Micro AM2 BIOS Setup Reset Configuration Data The system BIOS supports update ESCD to the memory locations. These locations (4K) are reserved in the system BIOS. If the Disabled settings will be shown on the screen only if "Manual" is chosen for the resources controlled by function. Legacy - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 39
K8M800 Micro AM2 BIOS Setup PCI / VGA Palette Snoop Choose Disabled or Enabled. Some graphic controllers which are not VGA compatible take the output from a VGA controller and map - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 40
K8M800 Micro AM2 BIOS Setup 8 PC Health Status „ Figure 8: PC Health Status Shutdown Temperature This item allows you to set up the CPU shutdown Temperature. The Choices: 70℃/ 158℉, 75℃/ 167℉, 80℃/ 176℉, 85℃/ 185℉(default) CPU Vcore/ 3.3V/ +5.0V/ +12V/DDR Voltage/ LDT Voltage/Voltage Battery Detect - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 41
K8M800 Micro AM2 BIOS Setup SYS FAN Speed This field displays the speed of the SYSTEM fan. Show H/W Monitor in POST If you computer contain a monitoring system, it will - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 42
K8M800 Micro AM2 BIOS Setup 9 Frequency/ Voltage Control „ Figure 9: Frequency/ Voltage Control CPU Vcore The Choices: Default (default), +0.15V, +0.10V, +0.05V. DDR Voltage This item allows you to select DDR Voltage. The Choices: 1.95V (default), 2.05V, 2.15V, 2.25V. - Biostar K8M800MAM2 | K8M800 MICRO AM2 bios guide - Page 43
K8M800 Micro AM2 BIOS Setup CPU CLOCK This item allows you to select CPU Clock, and CPU over clocking The Choices: 200Mhz (default), Disabled. Min= 200 Max= 232 Key in a DEC number. Special Notice: If unfortunately, the system's frequency that you are
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
 |
 |
K8M800 Micro AM2 BIOS Setup
i
BIOS Setup
.........................................................................................................
1
1
Main Menu
.............................................................................................................................
3
2
Standard CMOS Features
.......................................................................................................
6
4
Advanced Chipset Features
..................................................................................................
16
5
Integrated Peripherals
...........................................................................................................
23
6
Power Management Setup
....................................................................................................
30
7
PnP/PCI Configurations
.......................................................................................................
36
8
PC Health Status
...................................................................................................................
39
9
Frequency/ Voltage Control
.................................................................................................
41