Biostar M6VLR M6VLR user's manual - Page 53

Onboard Parallel Port

Get Biostar M6VLR PDF manuals and user guides View all Biostar M6VLR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 2 BIOS Setup Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. The Choices: Auto (default), Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3. Onboard IR Port Select IR Address. The Choices: Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled (default). UART 2 Mode This item allows you to determine which Infrared (IR) function onboard I/O chip. The Choices: HPSIR (default), ASKIR. IR Function Duplex This item allows you to decide to active IR transmission delay. The Choices: Half (default), Full. TX, RX inverting enable This item allows you to determine the active of Rx,Tx. The Choices: No/Yes (default), No/No, Yes/No, Yes/Yes. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O Address. The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled. Onboard Parallel Mode The default value is Normal. EPP Using Parallel Port as Enhanced Parallel 2-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
Chapter 2
BIOS Setup
2-19
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the
system board and you wish to use it. If install and FDC or the system has no
floppy drive, select Disabled in this field.
The Choices: Enabled
(default), Disabled.
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial ports.
The Choices: Auto
(default), Disabled, 3F8/IRQ4, 2F8/IRQ3,
3E8/IRQ4, 2E8/IRQ3.
Onboard IR Port
Select IR Address.
The Choices:
Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,
2E8/IRQ3,
Disabled
(default).
UART 2 Mode
This item allows you to determine which Infrared (IR) function onboard I/O chip.
The Choices: HPSIR
(default), ASKIR.
IR Function Duplex
This item allows you to decide to active IR transmission delay.
The Choices: Half
(default), Full.
TX, RX inverting enable
This item allows you to determine the active of Rx,Tx.
The Choices: No/Yes
(default), No/No, Yes/No, Yes/Yes.
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O Address.
The Choices: 378/IRQ7
(default), 278/IRQ5, 3BC/IRQ7, Disabled.
Onboard Parallel Mode
The default value is Normal.
EPP
Using Parallel Port as Enhanced Parallel