Biostar TFORCE 945P BIOS SETUP MANUAL - Page 21

On-chip Secondary PCI IDE, IDE Primary/Secondary/Master/Slave UDMA, SATA Mode - driver

Get Biostar TFORCE 945P PDF manuals and user guides View all Biostar TFORCE 945P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

TForce 945P BIOS Manual Mode4. On-chip Secondary PCI IDE This item allows you to enable or disable the primary/ secondary IDE Channel. The Choices: Enabled (default), Disabled. IDE Primary/Secondary/Master/Slave UDMA Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. SATA Mode This item allows you to choose SATA Mode. The Choices: IDE (default),RAID,AHCI. On-Chip Serial ATA This item allows you to choose: Disabled: disabled SATA Controller Combined Mode: PATA and SATA are combined max of 2 IDE drivers in each channel. Enhanced Mode: enabled both SATA and PATA max of 6 IDE drivers are supported. SATA Only: SATA is operating in legacy mode. The Choices: Default (default), Auto, Combined Mode, Enhanced Mode, and SATA only. SATA PORT Speed Settings This item allows you to set SATA PORT Speed. The Choices: Disabled (default),Force GEN I, Force GEN II. PATA IDE Mode This item allows you to choose PATA IDE Mode. The Choices: Primary (default), Secondary. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
TForce 945P
BIOS Manual
Mode4.
On-chip Secondary PCI IDE
This item allows you to enable or disable the primary/ secondary IDE Channel.
The Choices: Enabled
(default), Disabled.
IDE Primary/Secondary/Master/Slave UDMA
Ultra DMA/100 functionality can be implemented if it is supported by
the IDE hard drives in your system. As well, your operating
environment requires a DMA driver (Windows 95 OSR2 or a third
party IDE bus master driver). If your hard drive and your system
software both support Ultra DMA/100, select Auto to enable BIOS
support.
The Choices: Auto
(default), Disabled.
SATA Mode
T
his item allows you to choose SATA Mode.
The Choices: IDE
(default),RAID,AHCI.
On-Chip Serial ATA
This item allows you to choose:
Disabled:
disabled SATA Controller
Combined Mode:
PATA and SATA are combined max of 2 IDE drivers
in each channel.
Enhanced Mode:
enabled both SATA and PATA max of 6 IDE drivers
are supported.
SATA Only:
SATA is operating in legacy mode.
The Choices: Default
(default), Auto, Combined Mode, Enhanced Mode,
and SATA only.
SATA PORT Speed Settings
This item allows you to set SATA PORT Speed.
The Choices: Disabled
(default),Force GEN I, Force GEN II.
PATA IDE Mode
This item allows you to choose PATA IDE Mode.
The Choices: Primary
(default), Secondary.
20