Bissell Powergroom Multi-Cyclonic Canister Vacuum 1654 User Guide - Page 4
Replacement Parts
View all Bissell Powergroom Multi-Cyclonic Canister Vacuum 1654 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
D Care & Storage D1 - Empty the dirt cup Empty the dirt cup as soon as the dirt reaches the "FULL" lines on the sides of the dirt cup. D3 - Replacing the post-motor filter The post-motor filter assists in the filtration process to return cleaner air to the room. Use only BISSELL replacement filters. 1. Unplug the vacuum from electrical outlet. 1. Unplug the vacuum from the electrical outlet. 2. Press the dirt cup release button on the carry handle and lift up to remove the dirt cup. 3. Choose an emptying method. Method #2 is recommended for allergy suffers. Method #1 - Hold the dirt cup over a trash bin and push the emptying button to open the bottom. Close the bottom after the dirt empties. 2. Remove the filter door (located in the wheel next to the on/ off switch of the vacuum) by twisting it counter-clockwise and pulling out and away from the vacuum 3. The post-motor filter can be hand washed in cold water with a mild detergent. Rinse well and air dry thoroughly before placing back into the vacuum. 4. Replace the filter door by aligning the tabs up with the slots on inside the wheel and turning clockwise until you hear a click. Method #2 - Place a plastic bag over the bottom of the dirt cup. Push the D4 - Cleaning the cyclone emptying button through the plastic 1. Remove the dirt cup from the dirt cup to open the bottom. After the dust lid and cyclone assembly by twisting it settles, close the bottom and remove counter-clockwise and pulling away. the bag to discard. 2. Remove the cyclone by twisting it 4. Replace the dirt cup by placing it back into clockwise then pulling down and away from the vacuum and pushing down on the carry the dirt tank lid, over the secondary cyclone handle until it snaps back into place. fine dirt collector. D2 - Cleaning the dirt cup filter Use only BISSELL replacement filters in your vacuum. 1. Unplug the vacuum from the electrical outlet. 2. The dirt cup filters can be reached by removing the dirt cup from the vacuum and lift up the filter cup release latch. Pull filter upwards to remove. 3. The cyclone can be washed in cold water with a mild detergent. Make sure it is completely dry before replacing. 4. Replace the cyclone by sliding it over the bottom of the secondary cyclone dirt collector and lining it up with the lock/unlock arrow before twisting counter‑clockwise until you hear a click. 5. Replace the dirt cup and twist clockwise to lock. 3. The dirt cup filter can be can be hand washed in cold water with a mild detergent. Rinse well and air dry thoroughly before placing back onto the filter frame base. 4. Close dirt cup lid and replace dirt cup back onto product. To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical socket before performing maintenance or care. Do not operate cleaner with damp or wet filters or without all filters in place. This product is intended for household use only and not for commercial or industrial use. Vacuuming of dust from products like plaster, concrete or ashes will damage the motor and void the warranty. Clearing clogs from the dirt cup 5. Reach up into the dirt cup to clear any dirt or debris from the dirt cup. 1. Unplug the vacuum from electrical outlet. 2. Remove the dirt cup from the vacuum, 6. Check to see if there are any clogs in the suction inlet. following steps 1-3 of Emptying the dirt cup on page 6. 7. After clearing any dirt or debris from the dirt cup, replace the dirt cup filter 3. Remove the dirt cup filter assembly from assembly back in the dirt cup following the dirt cup, following step 2 of Clean the D2 - Cleaning the dirt cup filter on page 6. dirt cup filter on page 6. 4. Tap the dirt cup filter assembly over a garbage container to remove any dirt or debris from the cyclone screen that surrounds the dirt cup filter. Replacement Parts These items are available for purchase as accessories for your BISSELL vacuum: To purchase visit www.BISSELL.ca. PART # PART NAME 160-7710 Post-Motor Filter PART # PART NAME 160-5295 Dirt Cup Filter 160-7546 Dusting Brush 160-6491 PowerFoot 160-6494 Hose with Handle 160-6493 Telescopic Extension Wand 160-7545 Crevice Tool 160-7461 Upholstery Tool www.BISSELL.ca 6 7