Bosch SGE68X55UC Instruction manual - Page 31
AquaSensor, Switching the appliance on, Time display, Delay start
View all Bosch SGE68X55UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
AquaSensor The AquaSensor is an optical measuring device which measures the cleanliness of the rinse water. The AquaSensor is used according to the wash cycle. If the AquaSensor is active, "clean" rinse water can be transferred to the next rinse and water consumption can be reduced by 0.8-1-5 gal (3-6 liters). If the rinse water is not yet clear, the water is drained and is replaced with fresh water. In the automatic wash cycles the temperature and running time can also be adjusted to the degree of soiling. Switching the appliance on 1. Turn the water supply on fully. 2. Press the On/Off button (. The AUTO wash cycle has been preset as a default whenever the appliance starts. This wash cycle remains selected if no other wash cycle button 0 is pressed. Select any desired option. 3. Press Start button P. Wash cycle sequence starts. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Close the appliance door and press the Start button P again. Operating the Dishwasher en-us Time display When a wash cycle is selected the remaining wash cycle time is shown on the display 8. The wash cycle time is determined during the wash cycle by the water temperature, the amount of dishes, as well as the degree of soiling and may vary (depending on the selected wash cycle). Delay start You can delay the start of the cycle in one hour increments up to 24 hours. œ:‹, 1 hour delay œ:ƒ... 24 hours delay To set Delay start: 1. Press On/Off button (. Select a cycle. 2. Press Delay button @ until the displayed time corresponds with your requirements. 3. Press Start button P to activate Delay start. To cancel Delay start: 1. Press Delay button @ until œ:‹‹ is indicated on the digital display 8. 2. Press Start button P to save setting. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Close the appliance door and press the Start button P again. 31
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108