Bosch SHE3AEM5N Use and Care Manuals - Page 30

Issue, Cause and troubleshooting, Reset

Get Bosch SHE3AEM5N PDF manuals and user guides View all Bosch SHE3AEM5N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

en-us Troubleshooting Issue All LEDs light up or flash. Cause and troubleshooting Electronics have detected a fault. 1. Press the main switch button for approx. 4 seconds. → "Controls", Page 8 The appliance is reset and restarted. 2. If the problem occurs again: ‒ Switch off the appliance. ‒ Unplug the power plug or switch off the circuit breaker in the fuse box. ‒ Wait at least 2 minutes. ‒ Switch on the circuit breaker in the fuse box or plug in the power plug. ‒ Switch on the appliance. 3. If the problem occurs again: ‒ Contact customer service. → "Customer Service", Page 32 Water is left in the appliance at the Filter system or area under the filters is blocked. end of the program. 1. Clean the Filters → Page 22. 2. Clean the Drain pump → Page 31. Program has not yet ended. ▶ Wait until the program ends or terminate the program with Reset. ▶ → "Terminating the wash cycle", Page 18 Appliance cannot be switched on Software update is taking place. or operated. ▶ Wait until the software update has finished. Appliance functions have failed. 1. Pull out the power cord plug or switch off the breaker. 2. Wait at least 2 minutes. 3. Connect the appliance to the power supply. 4. Switch the appliance on. Appliance does not start. The breaker has tripped. ▶ Check the relevant breaker. Power cord is not inserted. 1. Check whether the power outlet is working. 2. Check whether the power cord plug is properly inserted in the power outlet and on the rear of the appliance. Appliance door is not closed properly. ▶ Close the appliance door. Wash cycle starts up automatically. You did not wait until the cycle ended. ▶ → "Terminating the wash cycle", Page 18 Appliance stops during the cycle or Appliance door is not closed properly. cuts out. ▶ Close the appliance door. Power and/or water supply has been interrupted. 1. Check the power supply. 2. Check the water supply. Upper rack is pressing against inner door and preventing appliance door from being closed securely. ▶ Check whether the rear panel of the appliance is being pressed in by a power outlet or a hose holder that has not been removed. ▶ Arrange the dishware so that no parts project beyond the rack and prevent the appliance door from closing properly. Appliance door cannot be closed. Door lock has been activated. ▶ Close the appliance door with greater force. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
en-us
Troubleshooting
30
Issue
Cause and troubleshooting
All LEDs light up or flash.
Electronics have detected a fault.
1.
Press the main switch button for approx. 4 seconds.
→
"Controls", Page 8
The appliance is reset and restarted.
2.
If the problem occurs again:
‒
Switch off the appliance.
‒
Unplug the power plug or switch off the circuit breaker in the fuse box.
‒
Wait at least 2 minutes.
‒
Switch on the circuit breaker in the fuse box or plug in the power plug.
‒
Switch on the appliance.
3.
If the problem occurs again:
‒
Contact customer service.
→
"Customer Service", Page 32
Water is left in the appliance at the
end of the program.
Filter system or area under the filters is blocked.
1.
Clean the Filters
→
Page 22
.
2.
Clean the Drain pump
→
Page 31
.
Program has not yet ended.
▶
Wait until the program ends or terminate the program with
Reset
.
▶
→
"Terminating the wash cycle", Page 18
Appliance cannot be switched on
or operated.
Software update is taking place.
▶
Wait until the software update has finished.
Appliance functions have failed.
1.
Pull out the power cord plug or switch off the breaker.
2.
Wait at least 2 minutes.
3.
Connect the appliance to the power supply.
4.
Switch the appliance on.
Appliance does not start.
The breaker has tripped.
▶
Check the relevant breaker.
Power cord is not inserted.
1.
Check whether the power outlet is working.
2.
Check whether the power cord plug is properly inserted in the power outlet and
on the rear of the appliance.
Appliance door is not closed properly.
▶
Close the appliance door.
Wash cycle starts up
automatically.
You did not wait until the cycle ended.
▶
→
"Terminating the wash cycle", Page 18
Appliance stops during the cycle or
cuts out.
Appliance door is not closed properly.
▶
Close the appliance door.
Power and/or water supply has been interrupted.
1.
Check the power supply.
2.
Check the water supply.
Upper rack is pressing against inner door and preventing appliance door from being
closed securely.
▶
Check whether the rear panel of the appliance is being pressed in by a power
outlet or a hose holder that has not been removed.
▶
Arrange the dishware so that no parts project beyond the rack and prevent the
appliance door from closing properly.
Appliance door cannot be closed.
Door lock has been activated.
▶
Close the appliance door with greater force.