Bosch SHV89PW53N Instructions for Use - Page 36
Tone volume, Button volume, Greeting, Factory setting, Switching the appliance on, Delay start time
View all Bosch SHV89PW53N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 36 highlights
en-us Operating the Dishwasher Tone volume The end of the wash cycle is indicated by a buzzer. You can also change this setting. Button volume When you are operating the dishwasher, a signal sounds whenever a button is pressed. You can control the volume of the signal. If you do not like the button volume, you can switch it off. Greeting When you switch on the dishwasher, the brand logo appears. You can switch off the brand logo. Factory setting You can reset all settings to the factory setting. Switching the appliance on 1. Turn the water supply on fully. 2. Open the door. 3. Switch on On/Off switch (. The Auto wash cycle has been preset as a default whenever the appliance starts. This wash cycle remains selected if no other wash cycle button 0 is pressed. 4. Press Start button )". 5. Close the door. Wash cycle sequence starts. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. Delay start time You can delay the start of the wash cycle by up to 24 hours. Depending on the setting of the time display, the end of cycle is indicated with "Finish in" (for example 3h 25m) or "Finish at" (for example 15:20 hours). 1. Open the door. 2. Switch on On/Off switch (. 3. Select wash cycle 0. 4. Press Delay start button `. 5. Keep pressing the setting buttons + - X until the displayed time corresponds with your requirements. 6. Press Start button )", timer programming is activated. 7. To delete the Delay start time, press Start button )" for about 3 seconds. 8. Close the door. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. InfoLight® While the wash cycle is running, a light spot shines on the floor under the appliance door. Do not open the appliance door until the light point is no longer visible on the floor. If the appliance door is not completely closed, the light spot flashes. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. In darkened rooms, some light scattering may be visible. This is normal and cannot be changed. You can switch the Infolight on or off. 36
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108