Home » Bosch Manuals » Dishwashers » Bosch SHXM63WS5N » Manual Viewer

Bosch SHXM63WS5N Instructions for Use - Page 31

Warning, Caution

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Auto power off This setting determines the length of time the control panel stays illuminated after the cycle is complete. To save energy the recommended setting is ˜:‹,. This setting can be adjusted from ˜:‹‹ to ˜:‹ƒ. dishwasher does not turn off automatically dishwasher turns off automatically after 1 minute dishwasher turns off automatically after 120 minutes (2 hours) To change the setting: 1. Open the door. 2. Press On/Off button (. 3. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number). 4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value •:‹... 5. Press function key # until the display 8 indicates ˜:‹x. 6. Press function key 3 until the display corresponds with your requirements. 7. Press Start button P. Switching off the appliance Short time after the end of the wash cycle: 1. Open the door. 2. Switch off On/Off button (. 3. Turn off water supply. 4. Remove the utensils when they have cooled down. Operating the Dishwasher en-us 9 WARNING RISK OF INJURY! To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. Interrupting the wash cycle 9 CAUTION Expansion (overpressure) may cause the appliance door to open and/or water to escape! If the door was opened on an appliance which has a hot water connection or is heated, always leave the door ajar for several minutes and then close. 1. Open the door. 2. Switch off On/Off switch (. The LED's go out. The wash cycle is saved. 3. To continue the wash cycle, switch on the On/Off switch ( again. 4. Close the door. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Press the Start button again and close the appliance door. 31

Section	Page
Table of contents	3
en-us Operating instructions	3
( Safety Definitions 5	3
( IMPORTANT SAFETY INSTRUCTIONS 6	3
ƒ Causes of Damage 9	3
* Getting Started 10	3
+ Water softening system / special salt 13	3
, Rinse Aid 15	3
- Loading the Dishwasher 16	3
. Detergent 24	3
/ Dishwasher Cycles 26	3
0 Dishwasher Cycle Options 27	3
1 Operating the Dishwasher 29	3
2 Care and Maintenance 33	3
3 Troubleshooting 37	3
4 Customer Service 41	3
‡ Statement of Limited Product Warranty 42	3
( Safety Definitions	5
Safety Definitions	5
9 WARNING	5
9 CAUTION	5
NOTICE	5
Note:	5
( IMPORTANT SAFETY INSTRUCTIONS	6
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
To reduce the risk of fire, electrical shock, or serious injury, observe the following:	6
Risk of fire, electrical shock, or serious injury	6
9 WARNING	6
Risk of injury or death!	6
9 WARNING	6
Risk of injury!	6
9 WARNING	6
Risk of electrical shock or fire!	6
9 WARNING	6
Health hazard!	6
GROUNDING INSTRUCTIONS	7
9 WARNING	7
Risk of electric shock!	7
Safe Operation	7
9 CAUTION	7
9 WARNING	7
Risk of injury!	7
Child Safety	8
Proper Care and Maintenance	8
9 WARNING	8
Risk of explosion!	8
NOTICE	8
9 WARNING	8
State of California Proposition 65 Warnings!	8
ƒ Causes of Damage	9
Causes of Damage	9
NOTICES	9
* Getting Started	10
Getting Started	10
Appliance overview	10
Operating panel	11
Dishwasher interior components	11
Display indicators	11
Menu overview	12
Setting	12
Factory setting	12
Description	12
+ Water softening system / special salt	13
Instructions for use of included “Water Hardness Test Strip”	13
1. Run the water at the kitchen sink for 5 minutes.	13
2. Dip the end of the test strip with the colored squares into the tap water for 1 second and shake off excess water.	13
3. After one minute, compare the test strip to the chart below and determine the Dishwasher Water Softener setting.	13
4. Adjust the dishwasher Water Softener setting. * 'Adjusting the water softening system' on page 14 *	13
5. If required, add salt to the dishwasher salt chamber as shown. ~ Page 14	13
Adjusting the water softener settings	13
Using the test strip included with your dishwasher (Purchased test strips may have a different scale)	13
Water softener setting	13
Add salt to salt dispenser	13
Water hardness onversion chart (only necessary if you purchase a different test strip)	13
ppm	13
gpg/°dH	13
Adjusting the water softening system	14
Set the softening system as follows:	14
1. Ask your local water utility company for the water hardness value of your tap water.	14
2. Required setting can be found in the water hardness table.	14
3. Open the door.	14
4. Switch on On/Off switch (.	14
5. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number).	14
6. Release both buttons. The indicator of function key # flashes and the display 8 indicates •:‹…. Press function key 3 to select the desired setting.	14
7. Save the selected setting by pressing the Start button P .	14
Using special dishwasher salt	14
NOTICE	14
Top off the salt as follows:	14
1. Undo the screw plug on the dispenser 1Z.	14
2. Fill the dispenser with water (required only when switching on the appliance for the first time).	14
3. Add salt as illustrated (do not use table salt, salt tablets or salt for use with whole house water softeners).	14
Using detergents with salt component	14
Detergent with a salt component	14
Switching off low salt indicator / water softening system	14
Switching off water softening system	14
, Rinse Aid	15
Rinse Aid	15
Note:	15
Adding rinse aid	15
NOTICE	15
1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pull it open.	15
2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill.	15
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	15
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	15
NOTICE	15
Setting the amount of rinse aid used	15
Setting	15
Amount	15
1. Open the door.	16
2. Press the On/Off button (.	16
3. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	16
4. Press the function key # until the display 8 shows §:‹†.	16
5. Press the function key 3 to select the desired setting.	16
6. Press the Start button P to save the setting.	16
Turning off rinse aid indicator	16
NOTICE	16
- Loading the Dishwasher	16
Loading the Dishwasher	16
Dishware material	16
Note:	16
Recommended	16
Not Recommended	17
Loading the racks	17
For best dishwashing results, observe the following when loading the dishwasher:	17
NOTICE	17
Loading the upper rack	17
Note:	17
Loading the lower rack	17
Recommended loading pattern	18
12 place setting	18
Lower rack 9\	18
Upper rack 12	18
Note:	18
Third rack 1*	18
Additional loading pattern	18
10 place setting	18
Lower rack 9\	18
Upper rack 12	18
Note:	18
Third rack 1*	19
Loading the silverware basket	19
9 WARNING	19
Risk of injury!	19
Long silverware basket	19
Note:	19
Unloading the dishwasher	19
Note:	19
Adjusting the height of the rack	20
With silverware basket	20
Upper rack	20
Lower rack	20
9.4 in (24 cm)	20
13.4 in (34 cm)	20
10.4 in (26.5 cm)	20
12 in (30.5 cm)	20
11.4 in (29 cm)	20
11 in (28 cm)	20
With third rack	20
Upper rack	20
Lower rack	20
7 in (18 cm)	20
13.4 in (34 cm)	20
8 in (20.5 cm)	20
12 in (30.5 cm)	20
9 in (23 cm)	20
11 in (28 cm)	20
RackMatic®	20
1. Pull the upper rack out of the dishwasher until it stops.	20
2. To lower the rack, push the RackMatic® lever inward.	20
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	20
Note:	20
Rack accessories	21
Flip tines	21
Third rack	21
Cup shelves	21
Removing/Installing third rack	22
Removing third rack 1*	22
1. Pull out third rack all the way (1).	22
2. Lift upper rollers over the stopper hooks of both rails (2).	22
3. Pull third rack out forward and upward so the the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	22
Installing third rack 1*	22
1. Pull out third rack rails all the way (1).	22
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	22
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	22
4. Push in third rack (4).	22
Removing/Installing upper rack with Rackmatic®	23
Removing upper rack 12	23
1. Pull out upper rack all the way (1).	23
2. Lift front rollers over the stopper hook of the rail (2).	23
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	23
Installing upper rack 12	23
1. Pull out upper rack rails all the way (1).	23
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	23
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	23
4. Push in upper rack (4).	23
. Detergent	24
Detergent	24
NOTICE	24
Note:	24
Wash Cycle	24
Hard Water/ Heavy Soil	24
Medium Water/ Medium Soil	24
Soft Water/ Little Soil	24
Adding detergent	25
1. If the detergent dispenser 92 is still closed, actuate the locking bar 9: to open it.	25
Note:	25
2. Pour detergent into the dry detergent dispenser 92 only. Add detergent. Do not overfill the detergent dispenser.	25
Note:	25
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed and press down firmly until it clicks.	25
Tip:	25
/ Dishwasher Cycles	26
Dishwasher Cycles	26
Wash cycle	26
Recommended use	26
Possible wash cycle option	26
Note:	26
Note:	26
The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9*. A single dose of detergent was inserted into the detergent dispenser 92, with no detergent...	26
0 Dishwasher Cycle Options	27
Dishwasher Cycle Options	27
Delay	27
Half Load	27
Sanitize	27
Extra Dry	27
Wash Cycle Information	28
Note:	28
Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...	28
1 Operating the Dishwasher	29
Operating the Dishwasher	29
Note:	29
9 WARNING	29
Risk of injury!	29
Protection against unintentional operation	29
This function will be activated when:	29
Note:	29
Operating the touch buttons	29
AquaSensor	29
AquaSensor	29
Switching the appliance on	30
1. Turn the water supply on fully.	30
2. Press the On/Off button (.	30
3. Press Start button P.	30
Note:	30
Time display	30
Delay Start	30
To set Delay start:	30
1. Open the door and press the On/Off button (. Select a cycle.	30
2. Press the Delay button from the wash cycle options H until the displayed time corresponds with your requirements.	30
3. Press the Start button P to activate Delay start.	30
To cancel Delay start:	30
1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display 8.	30
2. Press the Start button P to save setting.	30
Note:	30
Wash cycle end	30
To change the signal volume:	30
1. Open the door.	30
2. Press the On/Off button (.	30
3. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number).	30
4. Release both buttons. The LED for function key # flashes and teh digital display shows the factory setting •:‹….	30
5. Press function key # until the display shows ›:‹ƒ.	30
6. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value ›:‹„, the display jumps back to ›:‹‹ (off).	30
7. Press Start button P to save the setting.	30
Auto power off	31
To change the setting:	31
1. Open the door.	31
2. Press On/Off button (.	31
3. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number).	31
4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value •:‹…	31
5. Press function key # until the display 8 indicates ˜:‹x.	31
6. Press function key 3 until the display corresponds with your requirements.	31
7. Press Start button P.	31
Switching off the appliance	31
Short time after the end of the wash cycle:	31
1. Open the door.	31
2. Switch off On/Off button (.	31
3. Turn off water supply.	31
4. Remove the utensils when they have cooled down.	31
9 WARNING	31
Risk of injury!	31
Interrupting the wash cycle	31
9 CAUTION	31
1. Open the door.	31
2. Switch off On/Off switch (.	31
3. To continue the wash cycle, switch on the On/Off switch ( again.	31
4. Close the door.	31
Note:	31
Cancel a cycle (Reset)	32
1. Open the door and press and hold Start button P for approximately 3 seconds until the display reads ‹:‹‚, then close door again.	32
2. Wait about 1 minute while the dishwasher drains.	32
3. Open the door and press the On/Off button (.	32
Changing the wash cycle	32
Intensive drying	32
To change the setting:	32
1. Open the door.	32
2. Press On/Off button (.	32
3. Hold down function key # and press Start button P until the display 8 indicates •:x (x can be any number).	32
4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value •:‹…	32
5. Press function key # until the display 8 indicates the factory set value š:‹‹.	32
6. Press function key 3 to switch the feature on š:‹‚ or off š:‹‹.	32
7. Press Start button P to save setting.	32
InfoLight®	32
To change the setting:	32
1. Open the door.	32
2. Press the On/Off button (.	32
3. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number).	32
4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value •:‹…	32
5. Press the function key 3 to switch the InfoLight® feature on ‚:‹‚ or off ‚:‹‹.	32
6. Press Start button P to save the setting.	32
2 Care and Maintenance	33
Care and Maintenance	33
Overall condition of the dishwasher	33
NOTICE	33
9 WARNING	33
Filters	33
Filter components	33
The filter system 1b consists of three parts.	33
Cleaning intervals	34
Your filter system may need to be cleaned when:	34
Cleaning interval	34
Use this setting,	34
Note:	34
To check or clean the filter system:	34
1. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	34
2. Remove any residue and clean filters by rinsing under running water. Note: do not use abrasive brushes or steel wool, etc., as they may damage the filter.	34
3. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	34
Spray arms	35
Check spray arms 1:, 1R for grease and limescale deposits. If you find such deposits:	35
Drain pump	35
Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case:	35
Note:	35
Preparing your unit for vacation	36
NOTICE	36
Winterizing your unit	36
NOTICE	36
3 Troubleshooting	37
Troubleshooting	37
Problem	37
Cause	37
Action	37
Note:	37
Note:	38
Note:	38
Note:	38
Note:	39
Note:	39
Note:	40
--------	40
4 Customer Service	41
Customer Service	41
1. Call us at 1-800-944-2904	41
2. Contact Customer Service from our web site: www.bosch-home.com/us or www.bosch-home.ca	41
3. Contact your installer or the Bosch Authorized Service Contractor in your area.	41
4. Write us:	41
‡ Statement of Limited Product Warranty	42
Statement of Limited Product Warranty	42
What this Warranty Covers & Who it Applies to:	42
The limited warranty provided by BSH Home Appliances Corporation (BSH) in this Statement of Limited Product Warranty applies only to Bosch® dishwashers (“Product”) sold to you, the first using purchaser, provided that the Product was purchased:	42
How Long the Warranty Lasts	42
Extended Limited Warranty	42
BSH also provides these additional limited warranties:	42
Repair/Replace as Your Exclusive Remedy	43
Out of Warranty Product	43
Warranty Exclusions	43
The warranty coverage described herein excludes all defects or damage that are not the direct fault of BSH, including without limitation, one or more of the following:	43
How to Obtain Warranty Service	45
Table des matières	46
fr-ca Notice d'utilisation	46
( Indications de sécurité 48	46
( CONSIGNES DE SÉCURITÉ IMPORTANTES 49	46
ƒ Causes de pannes 53	46
* Mise en marche 54	46
+ Système d'adoucissement de l'eau / sels 57	46
, Produit de rinçage 60	46
- Chargement du lave-vaisselle 62	46
. Détergent 70	46
/ Cycles du lave-vaisselle 72	46
0 Options de cycles du lave-vaisselle 73	46
1 Mise en marche du lave-vaisselle 75	46
2 Entretien et maintenance 80	46
3 Dépannage 84	46
4 Service à la clientèle 89	46
‡ Déclaration de la garantie limitée du produit 90	46
( Indications de sécurité	48
Indications de sécurité	48
9 AVERTISSEMENT	48
9 ATTENTION	48
AVIS	48
Remarque :	48
( CONSIGNES DE SÉCURITÉ IMPORTANTES	49
CONSIGNES DE SÉCURITÉ IMPORTANTES	49
LISEZ ET CONSERVEZ CES INSTRUCTIONS	49
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :	49
Risque d'incendie, de choc électrique, ou de blessures graves	49
9 AVERTISSEMENT	49
Risque de blessure ou de décès !	49
9 AVERTISSEMENT	49
Risque de blessures !	49
9 AVERTISSEMENT	49
Risque de choc électrique ou d'incendie !	49
9 AVERTISSEMENT	49
Risque pour la santè !	49
INSTRUCTIONS DE MISE À LA TERRE	50
9 AVERTISSEMENT	50
Risque de choc électrique !	50
Fonctionnement normal	50
9 ATTENTION	50
9 AVERTISSEMENT	51
Risque de blessures !	51
Sécurité pour enfants	51
Entretien et maintenance corrects	51
9 AVERTISSEMENT	51
Risque d’explosion !	51
AVIS	52
9 AVERTISSEMENT	52
Mises en garde conformément à la proposition 65 de l'État de Californie !	52
ƒ Causes de pannes	53
Causes de pannes	53
AVIS	53
* Mise en marche	54
Mise en route	54
Vue d'ensemble de l'appareil	54
Panneau de commande	55
Composants internes du lave-vaisselle	55
Indicateurs	55
Réglages	56
Réglage	56
Réglages d'usine	56
Description	56
+ Système d'adoucissement de l'eau / sels	57
Instructions d'utilisation de la bandelette d'analyse de la dureté de l'eau comprise	57
1. Faites couler l'eau du robinet de la cuisine pendant 5 minutes.	57
2. Trempez l'extrémité de la bandelette avec les carrés de couleur dans l'eau du robinet pendant 1 seconde, puis secouez-la doucement pour en enlever l'excès d'eau.	57
3. Après une minute, comparez la bandelette d'analyse à la charte ci-dessous déterminez le réglage de l'adoucisseur d'eau.	57
4. Réglage de l'adoucisseur d'eau du lave-vaisselle. * 'Réglage du système d'adoucissement de l'eau' on page 58 *	57
5. Si nécessaire, ajouter de l'eau au compartiment salin de votre lave-vaisselle tel qu'indiqué. ~ Page 59	57
Réglage du système d'adoucissement de l'eau	58
Utiliser la bandelette d'analyse comprise avec votre lave-vaisselle (les bandelettes d'analyse achetées séparément pourraient avoir une échelle différente)	58
Réglage de l'adoucisse ur d'eau	58
Ajouter du sel au distributeur de sel	58
Charte de conversion de la dureté de l'eau (uniquement nécessaire si vous achetez une bandelette d'analyse différente)	58
ppm	58
gpg/°dH	58
Réglage du système d'adoucissement de l'eau	58
Réglez le système d'adoucissement comme suit :	58
1. Demandez le degré de dureté de votre eau courante à votre fournisseur d'eau.	58
2. Le réglage à effectuer se trouve dans le tableau de dureté de l'eau.	58
3. Ouvrez la porte.	58
4. Appuyez sur le bouton On/Off (Marche/arrêt) (.	58
5. Maintenez la touche # enfoncée et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur8 indique •:‹x (x peut être un nombre quelconque).	58
6. Relâchez les deux boutons. L'indicateur de la touche # clignote et l'afficheur 8 indique la •:‹…. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	58
7. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le paramètre.	58
Utilisation de sels spéciaux pour lave-vaisselle	59
AVIS	59
Remplissez les sels au maximum comme suit :	59
1. Retirez le bouchon à vis du distributeur 1Z.	59
2. Remplissez le distributeur d'eau (opération requise uniquement lors de la première mise sous tension de l'appareil).	59
3. Ajoutez le sel comme illustré (n'utilisez pas de sel de table, de comprimés de sel ni de sel destiné aux adoucisseurs d'eau de toute la maison).	59
Utilisation de détergents chargés en sels	59
Détergent chargé en sels	59
Éteindre l'indicateur de niveau bas de sels/le système d'adoucissement de l'eau	59
Éteindre le système d'adoucissement de l'eau	59
, Produit de rinçage	60
Produit de rinçage	60
Remarque :	60
Ajout de produit de rinçage	60
AVIS	60
1. Ouvrez le distributeur de liquide de rinçage 9* en appuyant sur le loquet du couvercle et en tirant celui-ci.	60
2. Ajoutez le produit de rinçage liquide au distributeur 9* à pleine capacité. Ne le remplissez pas outre mesure.	60
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	60
4. Essuyez tout excédent de produit de nettoyage déversé lorsque le réservoir est plein.	60
AVIS	60
Réglage de la quantité de produit de rinçage utilisé	61
Réglage	61
Quantité	61
1. Ouvrez la porte.	61
2. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	61
3. Maintenez la touche # enfoncée et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur 8 indique š:‹x (x peut être un nombre quelconque). Relâchez les deux boutons.	61
4. Appuyez sur la touche de fonction # jusqu'à ce que l'afficheur 8 indique §:‹†.	61
5. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	61
6. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le paramètre.	61
Désactivation de l'indicateur de produit de rinçage	61
AVIS	61
- Chargement du lave-vaisselle	62
Chargement du lave-vaisselle	62
Matériaux lavables au lave-vaisselle	62
Remarque :	62
Recommandé	62
Non recommandé	62
Chargement des paniers	63
Pour obtenir les meilleurs résultats, respectez les instructions suivantes lors du chargement de la vaisselle :	63
AVIS	63
Chargement du panier supérieur	63
Remarque :	63
Chargement du panier inférieur	63
Mode de chargement recommandé	63
Réglage 12 places	63
Panier inférieur 9\	63
Panier supérieur 12	64
Remarque :	64

Match case Limit results 1 per page

Operating the Dishwasher

en-us

Auto power off

This setting determines the length of

time the control panel stays

illuminated after the cycle is

complete.

To save energy the recommended

setting is

‹‚

This setting can be adjusted from

‹‹

‹ƒ

To change the setting:

Open the door.

Press

On/Off

button

(

Hold down function key

and

press

Start

button

until the

display

indicates

•

‹

x (x can

be any number).

Release both buttons.

The indicator of function key

flashes and the display

indicates the factory set value

•

‹…

Press function key

until the

display

indicates

‹

Press function key

until the

display corresponds with your

requirements.

Press

Start

button

Switching off the appliance

Short time after the end of the wash

cycle:

Open the door.

Switch off On/Off button

(

Turn off water supply.

Remove the utensils when they

have cooled down.

WARNING

RISK OF INJURY!

To avoid risk of injury, always

use caution when opening the

door during or following a wash

cycle as hot water or steam

may escape. Do not fully open

the door until water noises have

stopped and steam has

subsided.

Interrupting the wash cycle

CAUTION

Expansion (overpressure) may

cause the appliance door to

open and/or water to escape! If

the door was opened on an

appliance which has a hot water

connection or is heated, always

leave the door ajar for several

minutes and then close.

Open the door.

Switch off On/Off switch

(

The LED’s go out. The wash cycle

is saved.

To continue the wash cycle,

switch on the On/Off switch

(

again.

Close the door.

Note:

Your dishwasher is protected

against unintentional operation. If the

appliance door remains open for

more than 4 seconds after pressing

the Start button, the operation will be

paused. Press the Start button again

and close the appliance door.

‹‹

dishwasher does not turn off

automatically

‹‚

dishwasher turns off

automatically after 1 minute

‹ƒ

dishwasher turns off

automatically after

120 minutes (2 hours)