Home » Bosch Manuals » Dishwashers » Bosch SHXM98W75N » Manual Viewer

Bosch SHXM98W75N Instructions for Use - Page 18

Unloading the dishwasher, Adjusting the height of - 11

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

en-us Loading the Dishwasher Additional loading pattern 10 place setting Unloading the dishwasher When unloading the dishwasher, to prevent water from dripping onto dry dishes, unload the lower rack 9" first. Next, unload the silverware basket 1j followed by the upper rack 12, and then the third rack (if equipped). Note: Dishes are more likely to chip when unloading before cooling. Adjusting the height of the rack If required, the height of the upper rack 12 can be adjusted to create more space for taller utensils either in the upper or lower rack. With silverware basket Setting 1 max. ø Setting 2 max. ø Setting 3 max. ø Upper rack Lower rack 9.4 in (24 cm) 10.4 in (26.5 cm) 11.4 in (29 cm) 13.4 in (34 cm) 12 in (30.5 cm) 11 in (28 cm) With third rack Setting 1 max. ø Setting 2 max. ø Setting 3 max. ø Upper rack Lower rack 7 in (18 cm) 13.4 in (34 cm) 8 in (20.5 cm) 12 in (30.5 cm) 9 in 11 in (28 cm) (23 cm) Arrange large plates up to a diameter of 13.4 in (34 cm) in the lower basket 9" as illustrated. 18

Section	Page
Table of contents	3
en-us Operating instructions	3
( Safety Definitions 5	3
( IMPORTANT SAFETY INSTRUCTIONS 6	3
ƒ Causes of Damage 9	3
* Getting Started 10	3
, Rinse Aid 12	3
- Loading the Dishwasher 13	3
. Detergent 22	3
/ Dishwasher Cycles 24	3
0 Dishwasher Cycle Options 25	3
1 Operating the Dishwasher 28	3
2 Care and Maintenance 32	3
3 Troubleshooting 36	3
4 Customer Service 40	3
‡ Statement of Limited Product Warranty 41	3
( Safety Definitions	5
Safety Definitions	5
9 WARNING	5
9 CAUTION	5
NOTICE	5
Note:	5
( IMPORTANT SAFETY INSTRUCTIONS	6
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
To reduce the risk of fire, electrical shock, or serious injury, observe the following:	6
Risk of fire, electrical shock, or serious injury	6
9 WARNING	6
Risk of injury or death!	6
9 WARNING	6
Risk of injury!	6
9 WARNING	6
Risk of electrical shock or fire!	6
9 WARNING	6
Health hazard!	6
GROUNDING INSTRUCTIONS	7
9 WARNING	7
Risk of electric shock!	7
Safe Operation	7
9 CAUTION	7
9 WARNING	7
Risk of injury!	7
Child Safety	8
Proper Care and Maintenance	8
9 WARNING	8
Risk of explosion!	8
NOTICE	8
9 WARNING	8
State of California Proposition 65 Warnings!	8
ƒ Causes of Damage	9
Causes of Damage	9
NOTICES	9
* Getting Started	10
Getting Started	10
Appliance overview	10
Operating panel	11
Dishwasher interior components	11
Display indicators	11
Menu overview	11
Setting	11
Factory setting	11
Description	11
, Rinse Aid	12
Rinse Aid	12
Note:	12
Adding rinse aid	12
NOTICE	12
1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pull it open.	12
2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill.	12
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	12
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	12
NOTICE	12
Setting the amount of rinse aid used	12
Setting	12
Amount	12
1. Open the door.	13
2. Press the On/Off button (.	13
3. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	13
4. Press the function key # until the display 8 shows §:‹†.	13
5. Press the function key 3 to select the desired setting.	13
6. Press the Start button P to save the setting.	13
Turning off rinse aid indicator	13
NOTICE	13
- Loading the Dishwasher	13
Loading the Dishwasher	13
Dishware material	13
Note:	13
Recommended	13
Not Recommended	14
Loading the racks	14
For best dishwashing results, observe the following when loading the dishwasher:	14
NOTICE	14
Loading the upper rack	14
Note:	14
Loading the lower rack	14
Loading the third level rack	15
Recommended loading pattern	15
12 place setting	15
Lower rack 9\	15
Upper rack 12	15
Note:	15
Third rack 1*	15
Additional loading pattern	16
10 place setting	16
Lower rack 9\	16
Upper rack 12	16
Note:	16
Third rack 1*	16
Loading the silverware basket	16
9 WARNING	16
Risk of injury!	16
Long silverware basket	17
Note:	17
Suggested loading patterns	17
Recommended loading pattern	17
12 place setting	17
Additional loading pattern	18
10 place setting	18
Unloading the dishwasher	18
Note:	18
Adjusting the height of the rack	18
With silverware basket	18
Upper rack	18
Lower rack	18
9.4 in (24 cm)	18
13.4 in (34 cm)	18
10.4 in (26.5 cm)	18
12 in (30.5 cm)	18
11.4 in (29 cm)	18
11 in (28 cm)	18
With third rack	18
Upper rack	18
Lower rack	18
7 in (18 cm)	18
13.4 in (34 cm)	18
8 in (20.5 cm)	18
12 in (30.5 cm)	18
9 in (23 cm)	18
11 in (28 cm)	18
RackMatic®	19
1. Pull the upper rack out of the dishwasher until it stops.	19
2. To lower the rack, push the RackMatic® lever inward.	19
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	19
Note:	19
Rack accessories	19
Flip tines	19
Third rack	19
Cup shelves	20
Removing/Installing third rack	20
Removing third rack 1*	20
1. Pull out third rack all the way (1).	20
2. Lift upper rollers over the stopper hooks of both rails (2).	20
3. Pull third rack out forward and upward so the the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	20
Installing third rack 1*	20
1. Pull out third rack rails all the way (1).	20
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	20
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	20
4. Push in third rack (4).	20
Removing/Installing upper rack with Rackmatic®	21
Removing upper rack 12	21
1. Pull out upper rack all the way (1).	21
2. Lift front rollers over the stopper hook of the rail (2).	21
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	21
Installing upper rack 12	21
1. Pull out upper rack rails all the way (1).	21
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	21
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	21
4. Push in upper rack (4).	21
. Detergent	22
Detergent	22
NOTICE	22
Note:	22
Wash Cycle	22
Hard Water/ Heavy Soil	22
Medium Water/ Medium Soil	22
Soft Water/ Little Soil	22
Adding detergent	23
1. If the detergent dispenser 92 is still closed, actuate the locking bar 9: to open it.	23
Note:	23
2. Pour detergent into the dry detergent dispenser 92 only. Add detergent. Do not overfill the detergent dispenser.	23
Note:	23
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed and press down firmly until it clicks.	23
Tip:	23
/ Dishwasher Cycles	24
Dishwasher Cycles	24
Wash cycle	24
Recommended use	24
Possible wash cycle option	24
Note:	24
Note:	24
The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9*. A single dose of detergent was inserted into the detergent dispenser 92, with no detergent...	24
0 Dishwasher Cycle Options	25
Dishwasher Cycle Options	25
Delay	25
Half Load	25
Delicate	25
Sanitize	25
Eco	25
Extra Dry	25
Wash Cycle Information	26
Note:	27
Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...	27
1 Operating the Dishwasher	28
Operating the Dishwasher	28
Note:	28
9 WARNING	28
Risk of injury!	28
Protection against unintentional operation	28
This function will be activated when:	28
Note:	28
Operating the touch buttons	28
AquaSensor	28
AquaSensor	28
Switching the appliance on	29
1. Turn the water supply on fully.	29
2. Press the On/Off button (.	29
3. Press Start button P.	29
Note:	29
Time display	29
Delay Start	29
To set Delay start:	29
1. Open the door and press the On/Off button (. Select a cycle.	29
2. Press the Delay button from the wash cycle options H until the displayed time corresponds with your requirements.	29
3. Press the Start button P to activate Delay start.	29
To cancel Delay start:	29
1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display 8.	29
2. Press the Start button P to save setting.	29
Note:	29
Wash cycle end	29
To change the signal volume:	29
1. Open the door.	29
2. Press the On/Off button (.	29
3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	29
4. Press function key # until the display shows ›:‹ƒ.	29
5. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value ›:‹„, the display jumps back to ›:‹‹ (off).	29
6. Press Start button P to save the setting.	29
Auto power off	30
To change the setting:	30
1. Press the On/Off button (.	30
2. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number).	30
3. Release both buttons.	30
4. Press the function key # until the display 8 indicates ˜:‹x.	30
5. Press the function key 3 until the display corresponds with your requirements.	30
6. Press the Start button P.	30
Switching off the appliance	30
Short time after the end of the wash cycle:	30
1. Open the door.	30
2. Switch off On/Off button (.	30
3. Turn off water supply.	30
4. Remove the utensils when they have cooled down.	30
9 WARNING	30
Risk of injury!	30
Interrupting the wash cycle	30
9 CAUTION	30
1. Open the door.	30
2. Switch off On/Off switch (.	30
3. To continue the wash cycle, switch on the On/Off switch ( again.	30
4. Close the door.	30
Note:	30
Cancel a cycle (Reset)	31
1. Open the door and press and hold Start button P for approximately 3 seconds until the display reads ‹:‹‚, then close door again.	31
2. Wait about 1 minute while the dishwasher drains.	31
3. Open the door and press the On/Off button (.	31
Changing the wash cycle	31
Intensive drying	31
1. Open the door.	31
2. Press the On/Off button (.	31
3. Hold down function key # and press Start button P until the display 8 indicates š:x (x can be any number).	31
4. Release both buttons.	31
5. Press function key # until the display 8 indicates the factory set value š:‹‹.	31
6. Press function key 3 to switch the Extra dry feature on š:‹‚ or off š:‹‹.	31
7. Press Start button P to save setting.	31
InfoLight®	31
To change the setting:	31
1. Open the door.	31
2. Press the On/Off button (.	31
3. Hold down function key # and press Start button P until the display 8 indicates š:‹x (x can be any number). Release both buttons.	31
4. Press function key # until the display shows ‚:‹‚.	31
5. Press the function key 3 to switch the InfoLight® feature on ‚:‹‚ or off ‚:‹‹.	31
6. Press Start button P to save the setting.	31
2 Care and Maintenance	32
Care and Maintenance	32
Overall condition of the dishwasher	32
NOTICE	32
9 WARNING	32
Filters	32
Filter components	32
The filter system 1b consists of three parts.	32
Cleaning intervals	33
Your filter system may need to be cleaned when:	33
Cleaning interval	33
Use this setting,	33
Note:	33
To check or clean the filter system:	33
1. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	33
2. Remove any residue and clean filters by rinsing under running water. Note: do not use abrasive brushes or steel wool, etc., as they may damage the filter.	33
3. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	33
Spray arms	34
Check spray arms 1:, 1R for grease and limescale deposits. If you find such deposits:	34
Drain pump	34
Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case:	34
Note:	34
Preparing your unit for vacation	35
NOTICE	35
Winterizing your unit	35
NOTICE	35
3 Troubleshooting	36
Troubleshooting	36
Problem	36
Cause	36
Action	36
Note:	36
Note:	37
Note:	37
Note:	37
Note:	38
Note:	38
Note:	39
--------	39
4 Customer Service	40
Customer Service	40
1. Call us at 1-800-944-2904	40
2. Contact Customer Service from our web site: www.bosch-home.com/us or www.bosch-home.ca	40
3. Contact your installer or the Bosch Authorized Service Contractor in your area.	40
4. Write us:	40
‡ Statement of Limited Product Warranty	41
Statement of Limited Product Warranty	41
What this Warranty Covers & Who it Applies to:	41
The limited warranty provided by BSH Home Appliances Corporation (BSH) in this Statement of Limited Product Warranty applies only to Bosch® dishwashers (“Product”) sold to you, the first using purchaser, provided that the Product was purchased:	41
How Long the Warranty Lasts	41
Extended Limited Warranty	41
BSH also provides these additional limited warranties:	41
Repair/Replace as Your Exclusive Remedy	42
Out of Warranty Product	42
Warranty Exclusions	42
The warranty coverage described herein excludes all defects or damage that are not the direct fault of BSH, including without limitation, one or more of the following:	42
How to Obtain Warranty Service	44
Table des matières	45
fr-ca Notice d'utilisation	45
( Indications de sécurité 47	45
( CONSIGNES DE SÉCURITÉ IMPORTANTES 48	45
ƒ Causes de pannes 52	45
* Mise en marche 53	45
, Produit de rinçage 56	45
- Chargement du lave-vaisselle 58	45
. Détergent 67	45
/ Cycles du lave-vaisselle 69	45
0 Options de cycles du lave-vaisselle 70	45
1 Mise en marche du lave-vaisselle 73	45
2 Entretien et maintenance 77	45
3 Dépannage 82	45
4 Service à la clientèle 87	45
‡ Déclaration de la garantie limitée du produit 88	45
( Indications de sécurité	47
Indications de sécurité	47
9 AVERTISSEMENT	47
9 ATTENTION	47
AVIS	47
Remarque :	47
( CONSIGNES DE SÉCURITÉ IMPORTANTES	48
CONSIGNES DE SÉCURITÉ IMPORTANTES	48
LISEZ ET CONSERVEZ CES INSTRUCTIONS	48
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :	48
Risque d'incendie, de choc électrique, ou de blessures graves	48
9 AVERTISSEMENT	48
Risque de blessure ou de décès !	48
9 AVERTISSEMENT	48
Risque de blessures !	48
9 AVERTISSEMENT	48
Risque de choc électrique ou d'incendie !	48
9 AVERTISSEMENT	49
Risque pour la santè !	49
INSTRUCTIONS DE MISE À LA TERRE	49
9 AVERTISSEMENT	49
Risque de choc électrique !	49
Fonctionnement normal	49
9 ATTENTION	50
9 AVERTISSEMENT	50
Risque de blessures !	50
Sécurité pour enfants	50
Entretien et maintenance corrects	51
9 AVERTISSEMENT	51
Risque d’explosion !	51
AVIS	51
9 AVERTISSEMENT	51
Mises en garde conformément à la proposition 65 de l'État de Californie !	51
ƒ Causes de pannes	52
Causes de pannes	52
AVIS	52
* Mise en marche	53
Mise en route	53
Vue d'ensemble de l'appareil	53
Panneau de commande	54
Composants internes du lave-vaisselle	54
Indicateurs	54
Réglages	55
Réglage	55
Réglages d'usine	55
Description	55
, Produit de rinçage	56
Produit de rinçage	56
Remarque :	56
Ajout de produit de rinçage	56
AVIS	56
1. Ouvrez le distributeur de liquide de rinçage 9* en appuyant sur le loquet du couvercle et en tirant celui-ci.	56
2. Ajoutez le produit de rinçage liquide au distributeur 9* à pleine capacité. Ne le remplissez pas outre mesure.	56
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	56
4. Essuyez tout excédent de produit de nettoyage déversé lorsque le réservoir est plein.	56
AVIS	56
Réglage de la quantité de produit de rinçage utilisé	57
Réglage	57
Quantité	57
1. Ouvrez la porte.	57
2. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	57
3. Maintenez la touche # enfoncée et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur 8 indique š:‹x (x peut être un nombre quelconque). Relâchez les deux boutons.	57
4. Appuyez sur la touche de fonction # jusqu'à ce que l'afficheur 8 indique §:‹†.	57
5. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	57
6. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le paramètre.	57
Désactivation de l'indicateur de produit de rinçage	57
AVIS	57
- Chargement du lave-vaisselle	58
Chargement du lave-vaisselle	58
Matériaux lavables au lave-vaisselle	58
Remarque :	58
Recommandé	58
Non recommandé	58
Chargement des paniers	59
Pour obtenir les meilleurs résultats, respectez les instructions suivantes lors du chargement de la vaisselle :	59
AVIS	59
Chargement du panier supérieur	59
Remarque :	59
Chargement du panier inférieur	59
Chargement du panier du troisième étage	59
Mode de chargement recommandé	60
Réglage 12 places	60
Panier inférieur 9\	60
Panier supérieur 12	60
Remarque :	60
Troisième panier 1*	60
Configuration de chargement supplémentaire	60
Réglage 10 places	60
Panier inférieur 9\	60
Panier supérieur 12	61
Remarque :	61
Troisième panier 1*	61
Chargement du panier à ustensiles	61
9 AVERTISSEMENT	61
Risque de blessures !	61
Paniers à ustensiles longs	61
Remarque :	61
Profils de chargement suggérés	62
Mode de chargement recommandé	62
Réglage 12 places	62
Configuration de chargement supplémentaire	62
Réglage 10 places	62
Retrait de la vaisselle	63
Remarque :	63
Réglage de la hauteur du panier	63
Avec le panier à ustensiles	63
Panier supérieur	63
Panier inférieur	63
24 cm (9,4 po)	63
34 cm (13,4 po)	63
26,5 cm (10,4 po)	63
30,5 cm (12 po)	63
29 cm (11,4 po)	63
28 cm (11 po)	63
Avec le troisième panier	63
Panier supérieur	63
Panier inférieur	63
18 cm (7 po)	63
34 cm (13,4 po)	63
20,5 cm (8 po)	63
30,5 cm (12 po)	63
23 cm (9 po)	63
28 cm (11 po)	63
RackMatic®	63
1. Faites sortir le panier supérieur du lave-vaisselle jusqu'à la butée.	63
2. Pour abaisser le panier, poussez le levier RackMatic® lever vers l'intérieur.	63
3. Pour relever le panier, tenez les côtés du panier supérieur et soulevez-le.	63
Remarque :	63
Accessoires de panier	64
Peignes rabattables	64
3ème panier	64
Étagère pour tasses	64
Retirer/installer le troisième panier	65
Retirer le troisième panier 1*	65
1. Sortez le troisième panier jusqu'au bout (1).	65
2. Soulevez les galets supérieurs au-dessus des crochets de butée des deux glissières (2).	65
3. Sortez le troisième panier vers l'avant et vers le haut, de sorte que les coins de retenue et les galets inférieurs du panier passent au-dessus des crochets de butée des deux glissières (3).	65
Installer le troisième panier 1*	65
1. Sortez les glissières du troisième panier jusqu'au bout (1).	65
2. Insérez le troisième panier incliné. Assurez-vous que les crochets de butée des deux glissières coulissent entre les coins de retenue et les galets inférieurs du troisième panier (2).	65
3. Glissez le troisième panier à l'intérieur et soulevez les galets supérieurs au-dessus des crochets de butée avant des deux glissières (3).	65
4. Insérez le troisième panier en le poussant (4).	65
Retirer/installer le panier supérieur avec Rackmatic®	66
Retirer le panier supérieur 12	66
1. Sortez le panier supérieur jusqu'au bout (1).	66
2. Soulevez les galets avant sur le crochet de butée de la glissière (2).	66
3. Sortez le panier supérieur vers l'avant et vers le haut, de sorte que les galets supérieurs et inférieurs du panier coulissent au-dessus des crochets de butée des deux glissières (3).	66