Brother International BAS-370E Extended Option Output Instruction Manual - Eng - Page 5

Setting option output No. to ON using trigger data during sewing

Get Brother International BAS-370E PDF manuals and user guides View all Brother International BAS-370E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

(option output No. 15: OFF). This is for checking the case that the output conditions of ON and OFF are different. •Prepare the programmer, and display the output setting screen. ,Referring to the condition number table of machine operation mode (see page 191), set the option output No. 15 to ON when the condition No. 2 (after the feed is completed at the sewing start position) is set, Input on the setting screen as follows: ƒMove the cursor to "ON", press the + key. ON, OFF, and F/F are switched every time the + key is pressed. After setting "OFF", referring to the condition number table of machine operation mode (see page 191), set the option output No. 15 to OFF when the condition No. 3 (before sewing start) is set. Input on the setting screen as follows: „After overwriting the option program to the FD, press the P key to turn off the display of the programmer, and turn the power off and on again. ...Read the sewing data and carry out sewing. When the feed returns to the sewing start position, check that the left work clamp rises, and descends at sewing start. As shown in the above, when the timer 2 is "00", the option output number stays ON or OFF after the condition is met. 2-4 Setting option output No. to ON using trigger data during sewing No. 15 was set to ON at sewing start position in 2-2. The following procedure is to set No. 15 to ON during sewing. For OFF setting, keep the setting of 2-3 so that No. 15 stays OFF at sewing start. •Read the written data with the FD read icon. ,Referring to the condition number table of machine operation mode (see page 191), set the No. 15 to ON when the condition No. 14 (trigger data detection) is set. Input on the setting screen by overwriting as follows: 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
5
(option output No. 15: OFF). This is for checking the case that the output conditions of ON and
OFF are different.
±
Prepare the programmer, and display the output setting screen.
²
Referring to the condition number table of machine operation mode (see page 191), set the option
output No. 15 to ON when the condition No. 2 (after the feed is completed at the sewing start
position) is set, Input on the setting screen as follows:
³
Move the cursor to “ON”, press the + key. ON, OFF, and F/F are switched every time the + key is
pressed. After setting “OFF”, referring to the condition number table of machine operation mode
(see page 191), set the option output No. 15 to OFF when the condition No. 3 (before sewing start)
is set. Input on the setting screen as follows:
´
After overwriting the option program to the FD, press the P key to turn off the display of the
programmer, and turn the power off and on again.
µ
Read the sewing data and carry out sewing. When the feed returns to the sewing start position,
check that the left work clamp rises, and descends at sewing start.
°
As shown in the above, when the timer 2 is “00”, the option output number stays ON or OFF after
the condition is met.
2-4 Setting option output No. to ON using trigger data during sewing
°
No. 15 was set to ON at sewing start position in 2-2. The following procedure is to set No. 15 to
ON during sewing. For OFF setting, keep the setting of 2-3 so that No. 15 stays OFF at sewing
start.
±
Read the written data with the FD read icon.
²
Referring to the condition number table of machine operation mode (see page 191), set the No. 15
to ON when the condition No. 14 (trigger data detection) is set. Input on the setting screen by
overwriting as follows: