Brother International HL-1050 Quick Setup Guide - English - Page 21

Using the Printer Status Monitor Program, C:\RPCX>STMX, AUTOEXEC.BAT

Get Brother International HL-1050 PDF manuals and user guides View all Brother International HL-1050 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Using the Printer Status Monitor Program Type C:\RPCX>STMX and press the Enter key to make the Printer Status Monitor Program stay resident in your computer memory. If there are any changes to the printer status, it displays a message on your computer screen. If the printer status monitor program stays resident in your computer, you can monitor the printer status on your computer screen immediately using the hot-key sequence (Ctrl+Alt+R). To remove the Printer Status Monitor program from your computer memory, type C:\RPCX>STMX/R and press the Enter key. t The RPC works in the environment where your printer is directly connected to your computer. If you are using any printer buffer switches which do not support bi-directional communication between the printer and computer, the program works only in the PC to printer direction and cannot receive printer status information. t The program does not work with printers on a network. t If the RPC conflicts with some application software, exit your application software and then run the RPC. t The RPC may work in the DOS-compatible box screen mode of Windows, however, it is recommended that you completely exit from Windows to the DOS prompt before using the RPC. t The Printer Status Monitor and some other Terminate-and-Stay programs cannot coexist in the computer's memory. If they do not work properly together, use them one at a time. You can suspend the Printer Status monitor with any of the following methods or commands.  Type C:\RPCX>STMX/R and press the Enter key.  Hold the space bar down while executing the AUTOEXEC.BAT file at DOS startup to prevent the status monitor being loaded as a TSR program. -19 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
-19 -
Using the Printer Status Monitor Program
Type
C:\RPCX>STMX
and press the
Enter
key to make the Printer Status Monitor Program
stay resident in your computer memory. If there are any changes to the printer status, it
displays a message on your computer screen.
If the printer status monitor program stays resident in your computer, you can monitor the
printer status on your computer screen immediately using the hot-key sequence (
Ctrl
+
Alt
+
R
).
To remove the Printer Status Monitor program from your computer memory, type
C:\RPCX>STMX/R
and press the
Enter
key.
The RPC works in the environment where your printer is directly connected to your
computer. If you are using any printer buffer switches which do not support bi-directional
communication between the printer and computer, the program works only in the PC to
printer direction and cannot receive printer status information.
The program does not work with printers on a network.
If the RPC conflicts with some application software, exit your application software and
then run the RPC.
The RPC may work in the DOS-compatible box screen mode of Windows, however, it is
recommended that you completely exit from Windows to the DOS prompt before using the
RPC.
The Printer Status Monitor and some other Terminate-and-Stay programs cannot coexist in
the computer’s memory. If they do not work properly together, use them one at a time.
You can suspend the Printer Status monitor with any of the following methods or
commands.
±²
Type
C:\RPCX>STMX/R
and press the
Enter
key.
±²
Hold the space bar down while executing the
AUTOEXEC.BAT
file at DOS startup to
prevent the status monitor being loaded as a TSR program.