Brother International PE-700 Users Manual - English

Brother International PE-700 Manual

Get Brother International PE-700 PDF manuals and user guides View all Brother International PE-700 manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International PE-700 manual content summary:

  • Brother International PE-700 | Users Manual - English - Page 1
    GETTING READY EMBROIDERY APPENDIX Computerized Embroidery Machine Operation Manual
  • Brother International PE-700 | Users Manual - English - Page 2
    pay close attention to the needle. Do not use bent or damaged needles. • Keep fingers away from all moving parts. Special care is required around the machine needle. • Switch the machine to the symbol "O" position to turn it off when making any adjustments in the needle area. • Do not use a damaged
  • Brother International PE-700 | Users Manual - English - Page 3
    follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in the manual. Use accessories recommended by the
  • Brother International PE-700 | Users Manual - English - Page 4
    Instructions 1 Introduction ...5 Machine Features ...5 Accessories...6 Included accessories ...6 Optional accessories ...7 Names of Machine Parts and Their Functions 8 Front view ...8 Needle and embroidery foot section ...9 Right-side/rear view ...9 Operation buttons ...10 Operation panel ...11
  • Brother International PE-700 | Users Manual - English - Page 5
    partway through a design...65 Stopping while embroidering ...66 APPENDIX 69 Care and Maintenance ...70 Cleaning the machine surface ...70 Cleaning the race ...70 Attaching the Embroidery Foot 72 Attaching the embroidery Foot "Q" ...72 Troubleshooting ...74 Error messages ...78 Adjusting the LCD
  • Brother International PE-700 | Users Manual - English - Page 6
    Thank you for purchasing this embroidery machine. Before using the machine, carefully read the "Important Safety Instructions" (page 1), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can
  • Brother International PE-700 | Users Manual - English - Page 7
    X55260-153 130013-154 No. Part Name 10 Spool net 11 Operation manual 12 Quick reference guide 13 Embroidery foot "Q" (on machine) Embroidery set (large) 14 H 18cm X W 13 cm (H 7 inches X W 5 inches) 15 Scissors 16 Dust cover 17 Accessory bag Part Code U.S.A. / Canada Others XA5523-050
  • Brother International PE-700 | Users Manual - English - Page 8
    available as optional accessories. 1. 2. 3. 4. 5. 6. No. Part Name 1 Brother poly #90 bobbin thread Water solude stabilizer 2 Stabilizer material for embroidery 3 Embroidery card Part Code U.S.A. / Canada Other No. Part Name Part Code U.S.A. / Canada Other EBT-PE SA520 SA519 EBT
  • Brother International PE-700 | Users Manual - English - Page 9
    spool of thread on the spool pin. f Bobbin winder Use the bobbin winder when winding the bobbin. g Operation panel From the operation panel, patterns can be selected and edited, and operations for using the machine can be displayed (page 11). 8 h Embroidery unit connector slot Plug in the connector
  • Brother International PE-700 | Users Manual - English - Page 10
    insert the bobbin into the bobbin case. f Embroidery foot "Q" This presser foot is used for embroidering. a Handle Carry the machine by its handle when transporting the machine. b Handwheel Turn the handwheel toward you (counterclockwise) to raise and lower the needle. c Embroidery card slot Insert
  • Brother International PE-700 | Users Manual - English - Page 11
    embroidering. Red: The machine can not embroider. Orange: The machine is winding the bobbin thread, or the bobbin winder shaft is moved to the right side. b Needle position button Press the needle position button to raise or lower the needle. Pressing the button twice sews one stitch. c Thread
  • Brother International PE-700 | Users Manual - English - Page 12
    selection screen. g Settings key Press to display the settings screen. h Help key Press to get help on using the machine. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / embroidery unit attachment / embroidery frame attachment / needle replacement. 11
  • Brother International PE-700 | Users Manual - English - Page 13
    12
  • Brother International PE-700 | Users Manual - English - Page 14
    21 Checking machine operating procedures 23 Winding/Installing the Bobbin 24 Bobbin precautions 24 Winding the bobbin 24 Installing the bobbin 28 Upper Threading ...30 About the spool of thread 30 Threading the upper thread 30 Threading the needle 32 Threading the needle manually (without
  • Brother International PE-700 | Users Manual - English - Page 15
    is not attached, the machine does not operate.) For details, refer to "Attaching the embroidery unit" (page 15). ↓ 2 Checking the needle Use a needle matched to the fabric. For details on replacing the needle, refer to "Replacing the needle" (page 36). ↓ 3 Setting up the bobbin thread For the
  • Brother International PE-700 | Users Manual - English - Page 16
    describes how to attach the embroidery unit. Before turning on the machine, attach the embroidery unit to it. If the embroidery unit is not attached, the machine does not operate. 1 Embroidery unit precautions Attaching the embroidery unit Cautions for the embroidery unit will be explained
  • Brother International PE-700 | Users Manual - English - Page 17
    moves to its initial position. Make sure that the machine is completely stopped and follow the instructions below. Remove the embroidery frame. a • For details on removing the embroidery frame, refer to "Removing the embroidery frame" (page 48). Press , and then press . b a a Carriage X The
  • Brother International PE-700 | Users Manual - English - Page 18
    Hold the release button on the bottom left of d the embroidery unit, and slowly pull the embroidery unit to the left. 1 a a Release button X The embroidery unit separates from the machine. CAUTION ● Do not carry the embroidery unit by holding the release button compartment. Attaching the
  • Brother International PE-700 | Users Manual - English - Page 19
    . These things may damage the cord and cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use. ● Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a fire may result. 18
  • Brother International PE-700 | Users Manual - English - Page 20
    , be sure to attach the When you are finished using the machine, turn it off. embroidery unit to it. If the embroidery unit is not attached, the machine does not operate. (For details, In addition, before transporting the machine to another location, be sure to turn it off. 1 refer to "Attaching
  • Brother International PE-700 | Users Manual - English - Page 21
    , and operations for using the machine can be displayed (page 11). Viewing the LCD When the machine is turned on, the opening Embroidery patterns b Additional embroidery patterns c Alphabet patterns d Frame patterns e Embroidery card f Patterns stored in the machine's memory g Moves the embroidery
  • Brother International PE-700 | Users Manual - English - Page 22
    color/Time to embroider/ Needle count/Thread number (#123) Embroidery/Country/Madeira poly/ Madeira rayon/Sulky/Robison anton Display unit Selects the measurement units that are displayed (only for embroidering). mm/INCH Embroidery tension Adjusts the thread tension for embroidering (only for
  • Brother International PE-700 | Users Manual - English - Page 23
    GETTING READY Turn on the machine. a X The LCD comes on. Press b panel. (Settings key) on the operation X The settings screen appears. Press the item to be set. c Switch screens using (Previous
  • Brother International PE-700 | Users Manual - English - Page 24
    page. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / embroidery † Example: Upper threading 1 unit attachment / embroidery frame attachment / needle replacement on the LCD. Turn on the machine. a X The LCD comes on. Press b (Help key) on
  • Brother International PE-700 | Users Manual - English - Page 25
    place. CAUTION 1 ● Only use the Bobbin (part code: SA156, SFB: XA5539-151) designed specifically for this machine. Use of any other bobbin may result in injuries or damage to the machine. ● The included bobbin was designed specifically for this machine. If bobbins from other models are used, the
  • Brother International PE-700 | Users Manual - English - Page 26
    Place the spool of thread for the bobbin onto f the spool pin. Slide the spool onto the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. ● a a Spool cap (small) b Spool (cross-wound thread) c Space z When using thread that
  • Brother International PE-700 | Users Manual - English - Page 27
    , i and then pull it to the right. 1 a Thread guide plate a Thread guide Note z Make sure that the thread passes under the pretension disk. While holding the thread with your left hand, k wind the thread that was pulled out clockwise around the bobbin five or six times with your right hand. Note
  • Brother International PE-700 | Users Manual - English - Page 28
    the bobbin. 1 1 a Guide slit in bobbin winder seat (with built-in cutter) CAUTION ● Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle
  • Brother International PE-700 | Users Manual - English - Page 29
    the needle may break or the thread tension will be incorrect. ● The bobbin was designed specifically for this machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-151). 11
  • Brother International PE-700 | Users Manual - English - Page 30
    The cutter cuts the thread. Note z Make sure that the thread is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted correctly, reinsert the thread. 1 a Tension-adjusting spring Reattach the bobbin cover. g Insert the tab in the lower-left corner of the
  • Brother International PE-700 | Users Manual - English - Page 31
    needle. CAUTION ● When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle pin, and then thread the machine. Turn on the machine. a 1 a Needle position button X The needle is correctly raised when the
  • Brother International PE-700 | Users Manual - English - Page 32
    pass the thread behind the thread guide cover and to the front. 1 CAUTION ● If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break. a Thread guide cover Pass the thread under the thread guide plate, i and then pull it
  • Brother International PE-700 | Users Manual - English - Page 33
    to thread the needle. Memo z The needle threader can be used with sewing machine needles 75/11 through 100/16. z Thread with a thickness of 130/20 or thicker cannot be used with the needle threader. z If the needle threader cannot be used, refer to "Threading the needle manually (without using the
  • Brother International PE-700 | Users Manual - English - Page 34
    the left side b of the machine. Lower the needle threader lever on the left d side of the machine until it clicks, and then slowly return the lever to its original position. 1 1 1 a Cutter Note z If the thread is pulled through and cannot be cut correctly, lower the embroidery foot so that the
  • Brother International PE-700 | Users Manual - English - Page 35
    of the e thread through the embroidery foot hole. Threading the needle manually (without using the needle threader) X The upper threading is cannot be used with the needle threader, thread the needle as described below. Thread the machine to the needle bar thread a guide. • For details, refer to
  • Brother International PE-700 | Users Manual - English - Page 36
    are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent needles can easily break, possibly resulting in injuries. Embroidering with
  • Brother International PE-700 | Users Manual - English - Page 37
    fabric or paper under the embroidery d foot to cover the hole in the needle plate. Replace the needle as described below. Use the screwdriver and a needle that has been determined to be straight according to the instructions in "Checking the needle" (page 35). Press (Needle position button) once or
  • Brother International PE-700 | Users Manual - English - Page 38
    the flat side of the needle toward the rear f of the machine, insert the needle until it touches the needle stopper. 1 1 a Needle stopper While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. CAUTION ● Be sure to insert the needle until it touches the
  • Brother International PE-700 | Users Manual - English - Page 39
    GETTING READY 38
  • Brother International PE-700 | Users Manual - English - Page 40
    pattern 54 Using an embroidery card (sold separately 55 Embroidering 56 Embroidering attractive finishes .....56 Embroidering a pattern 57 Appliquéing 59 Editing and Saving Patterns 61 Adjusting the layout 61 Storing patterns 63 Adjusting the thread tension...........64 Resewing 65 Thread
  • Brother International PE-700 | Users Manual - English - Page 41
    the fabric, causing the needle to break. For the bobbin thread, use the embroidery bobbin thread. For details, refer to "Optional accessories" (page 7). Note z For good quality embroidery designs be sure to use embroidery thread designed for embroidery machines. z Before starting to embroider
  • Brother International PE-700 | Users Manual - English - Page 42
    denim, use a 90/14 home sewing machine needle. Memo z A 75/11 needle is already installed when the machine is purchased. z When replacing the needle, refer to "Replacing the needle" (page 36). 2 ■ Other Embroidery frames "small", "medium" and "extra large (multi-position)" are optional. For
  • Brother International PE-700 | Users Manual - English - Page 43
    embroidery designs. Memo z We recommend the stabilizer material for embroidery. Use a water soluble stabilizer on thin materials like organdy and fabrics with a nap like towels. For details, refer to "Optional accessories use stabilizer material for embroidery projects. The needle may break or bend
  • Brother International PE-700 | Users Manual - English - Page 44
    frame may be hit by the embroidery foot and cause injury or needle breakage. ■ Embroidery frame (medium)[option] Patterns with a height of up to 10 cm (4 inches) and a width of up to 10 cm (4 inches) can be embroidered. Loosen the embroidery frame adjustment a screw and remove the inner and
  • Brother International PE-700 | Users Manual - English - Page 45
    EMBROIDERY Press the inner frame in from the top of the c fabric. Line up on the inner frame and on outer frame. Press the inner frame in from the top of the f fabric again, lining up on the inner frame and on outer frame. Tighten the adjustment frame. Tighten the adjustment screw while removing
  • Brother International PE-700 | Users Manual - English - Page 46
    pattern can be embroidered in exactly the right position on the fabric. Line the mark on the fabric up with the base c line on the embroidery sheet. 2 Make a mark with a chalk pen at the center of a the position for the pattern to be embroidered. Place the inner frame with the fabric
  • Brother International PE-700 | Users Manual - English - Page 47
    pieces of fabric that cannot be stretched on an embroidery frame or thin pieces like ribbon are being embroidered, use stabilizer material as a base to stretch on the frame. We recommend stabilizer material for all embroidery. 1 2 3 1 3 2 1 3 a Stabilizer material b Tack or spray glue c Fabric After
  • Brother International PE-700 | Users Manual - English - Page 48
    embroidery frame. Attaching the embroidery frame Wind the embroidery bobbin thread onto the a bobbin and set it into the bobbin case. • For details, refer to "Winding/Installing the Bobbin not hit the needle with your finger or the embroidery frame. It may cause injury or needle breakage. While
  • Brother International PE-700 | Users Manual - English - Page 49
    foot lever even further. Make sure that the machine is completely stopped and follow the instructions below. Raise the presser foot lever. a a a Presser foot lever While pushing the lever of the embroidery b frame holder to the left, lift the embroidery frame up to remove it. Remove the back
  • Brother International PE-700 | Users Manual - English - Page 50
    patterns d Frame patterns e Embroidery card f Patterns stored in the machine's memory ■ Embroidery patterns (Embroidery patterns/ Additional embroidery patterns) There are total 136 patterns. The patterns are completed by changing the upper thread according to the instructions displayed on the
  • Brother International PE-700 | Users Manual - English - Page 51
    . [mm/inch] EMBROIDERY TENSION The thread tension for embroidering can be adjusted. [-8 to +8] MAX EMBROIDERY SPEED (SPM) The maximum embroidering speed can be selected. [650SPM/350SPM] NAME OF COLOR: Typical color name TIME: Time required for embroidering NEEDLE COUNT: Needle progress number #123
  • Brother International PE-700 | Users Manual - English - Page 52
    position for starting the embroidery. This is used when a specific color is not embroidered or when restarting the machine after power has been turned off in the middle of the operation. Press this key to select or cancel programmed thread cutting. Press or tension. to adjust the thread Press or
  • Brother International PE-700 | Users Manual - English - Page 53
    Selecting characters Specify the characters for embroidery. Memo z When "The pattern is too large for the embroidery frame." is displayed, no more characters can be entered. z Characters of different styles (sans serif, serif, and outline, etc.) cannot be combined. Select the alphabet
  • Brother International PE-700 | Users Manual - English - Page 54
    pattern There are total of 136 embroidery patterns, such as fruits and animals, stored in the machine's memory. 70 Embroidery patterns 66 Embroidery patterns Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples of completed patterns and the thread
  • Brother International PE-700 | Users Manual - English - Page 55
    EMBROIDERY Selecting a frame pattern 10 shapes, such as squares and circles, can be combined with 12 stitch types. Select the stitch. c Switch the screen using (Previous page key) (Next page key), and select from the 12 stitches. Memo z Refer to "Frame patterns" in the Quick reference guide
  • Brother International PE-700 | Users Manual - English - Page 56
    in their storage cases. z Use only embroidery cards manufactured for this machine. Using unauthorized cards may cause your machine to operate incorrectly. z Embroidery cards purchased in foreign countries may not work with your machine. z Large patterns supplied on embroidery cards may be difficult
  • Brother International PE-700 | Users Manual - English - Page 57
    important point is the appropriateness of the needle and thread being used. See the explanation of threads below. Thread Upper thread Bobbin thread Use embroidery thread, or country embroidery thread intended for use with this machine. Other embroidery threads may not yield optimum results. Use
  • Brother International PE-700 | Users Manual - English - Page 58
    Embroidery frames that can be used for embroidering b Current color step/Number of colors in design c Current name of color d Current color part e Next color part (page 50). Set the embroidery thread, thread the needle, b then pass the end of the thread through the embroidery foot hole. Give the
  • Brother International PE-700 | Users Manual - English - Page 59
    already been cut, otherwise the needle may break, the threads may become tangled or damage to the machine may occur. ● Do not press (Thread cutter button) if there is no fabric under the embroidery foot or while the machine is embroidering, otherwise damage to the machine may occur. • If the thread
  • Brother International PE-700 | Users Manual - English - Page 60
    -on stabilizer to the back of the appliqué piece fabric, and stretch it on the embroidery frame. Set up the thread for appliquéing. f Lower the presser foot lever, and press g (Start/stop button). X The position for the appliqué is stitched, and the machine stops. Lower the presser foot lever, and
  • Brother International PE-700 | Users Manual - English - Page 61
    EMBROIDERY Lower the presser foot lever, and press i (Start/stop button). Note z When "APPLIQUE MATERIAL", "APPLIQUE POSITION" and "APPLIQUE" are displayed, a specific color thread does not appear. Use a proper color thread to match the appliqué piece. Follow the instructions on the screen, and j
  • Brother International PE-700 | Users Manual - English - Page 62
    Horizontal mirror image key i Distance from the center j Embroidery size k Starting point key Press . b Embroidery frame size These flash if the pattern was resized, the layout was adjusted, or the recommended embroidery frame size was changed. Embroidery frame icons that appear in gray cannot be
  • Brother International PE-700 | Users Manual - English - Page 63
    EMBROIDERY Memo z If you make a note of the values in the lower part of screen when you change the size and position, you can embroider with the same size and layout even if you have to turn the power back on in the middle of your work. Starting point key Moves the needle start
  • Brother International PE-700 | Users Manual - English - Page 64
    patterns and the alphabet patterns you have customized can be stored in the machine's memory. Since the stored patterns will not be erased when the machine is turned off, you can always recall them for embroidery. This is convenient for storing names and the like. You can store up to
  • Brother International PE-700 | Users Manual - English - Page 65
    key) and (Next page key). b a c Adjusting the thread tension If embroidery fails, it is difficult to undo the thread and tension. Note z Characters saved from an embroidery card must have the embroidery card inserted in the machine in order to retrieve the memory saved from the embroidery card
  • Brother International PE-700 | Users Manual - English - Page 66
    resewn with the correct color. Press (Start/stop button) to stop the a machine. Thread runs out partway through a design When the upper thread or the bobbin thread runs out while embroidering, the machine stops. Move the needle back about 10 stitches and resume embroidering. Press . b Set up the
  • Brother International PE-700 | Users Manual - English - Page 67
    before it is complete, check the current needle count before turning off the machine. Memo z When the machine is turned off, the embroidery size and layout return to the original setting. Press (Start/stop button) to stop the a machine. Check the current needle count on the screen b and make a note
  • Brother International PE-700 | Users Manual - English - Page 68
    Press (Forward one color) to move to 2 i the beginning of the color you want to embroider. Press (Forward one stitch) to increase j the needle count. If is pressed continuously, it moves forward 1 -> 9 -> 30 stitches. Move forward to about 10 stitches before the total number of stitches
  • Brother International PE-700 | Users Manual - English - Page 69
    EMBROIDERY 68
  • Brother International PE-700 | Users Manual - English - Page 70
    are described in this chapter. Care and Maintenance 70 Cleaning the machine surface 70 Cleaning the race 70 Attaching the Embroidery Foot 72 Attaching the embroidery Foot "Q 72 Troubleshooting ...74 Error messages 78 Adjusting the LCD 81 Operation beep 81 Canceling the operation beep 82
  • Brother International PE-700 | Users Manual - English - Page 71
    cleaning the machine, otherwise injuries or an electric shock may occur. Remove the embroidery unit. c Grasp both sides of the needle plate cover, and d then slide it toward you. a a Needle plate cover X The needle plate cover is removed. Remove the bobbin case. e Grasp the bobbin case, and then
  • Brother International PE-700 | Users Manual - English - Page 72
    contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle may break. Insert the bobbin case so that the projection g on the bobbin case aligns with the spring. a b 2 1 a Projection b Spring 1 a Bobbin case Care and Maintenance 71
  • Brother International PE-700 | Users Manual - English - Page 73
    foot with your index finger wrapped around the lever at the back of the foot. a 1 a Needle position button Turn off the machine. b CAUTION ● Before attaching the embroidery foot, be sure to turn off the machine, otherwise injuries may occur if (Start/stop button) is accidentally pressed and the
  • Brother International PE-700 | Users Manual - English - Page 74
    . Firmly tighten the presser foot holder screw. g Turn the screwdriver toward the front. 3 CAUTION ● Do not hit the needle with your finger or the embroidery foot when attaching it. The needle may break or cause injury. ● Be sure to tighten the screw with the included screwdriver. If the screw is
  • Brother International PE-700 | Users Manual - English - Page 75
    it. Replace the embroidery foot. Contact your retailer or the nearest authorized service center. The bobbin case is scratched, or has a burr on it. Replace the bobbin case. Contact your retailer or the nearest authorized service center. A bobbin designed specifically for this machine is not used
  • Brother International PE-700 | Users Manual - English - Page 76
    is incorrect. Correctly install the bobbin thread. Adjust the tension of the upper thread. page 28 page 64 A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. page 24 Troubleshooting 75
  • Brother International PE-700 | Users Manual - English - Page 77
    the bobbin case. Contact your retailer or the nearest authorized service center. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. The thread does not pass through the eye of the needle
  • Brother International PE-700 | Users Manual - English - Page 78
    ., is plugged up. Remove the tangled thread. When the bobbin case is plugged up, clean the race. page 70 The thread tension is incorrect. Adjust the tension of the upper thread. page 64 If the embroidery unit carriage or 3 Embroidery not neatly done. Objects are placed near the carriage or
  • Brother International PE-700 | Users Manual - English - Page 79
    rethreading the machine, the thread tension may be wrong or the needle may break and cause injury. The machine is deleting a previously saved pattern. on the LCD was pressed when no card was inserted. The start/stop button or thread cutter button was pressed while the embroidery foot was raised
  • Brother International PE-700 | Users Manual - English - Page 80
    around the bobbin case, and the needle is bent and hitting the needle plate, etc., so the machine stops (refer to page 74). A card that cannot be used with this machine has been inserted, and you tried to select a pattern from the card. An embroidery card incompatible with this machine was inserted
  • Brother International PE-700 | Users Manual - English - Page 81
    APPENDIX Error Message Probable Cause The machine was turned on before the embroidery unit was attached. The bobbin winder is winding the bobbin. 80
  • Brother International PE-700 | Users Manual - English - Page 82
    Adjusting the LCD Operation beep If nothing appears on the LCD when the machine is turned on, the brightness of the LCD is either too light or too dark. In such a case, perform the following operation. Turn off the machine. a Each time a key is pressed you will hear one beep. If an incorrect
  • Brother International PE-700 | Users Manual - English - Page 83
    , it is set to beep each time an operation panel key is pressed. This setting can be changed so that the machine does not beep. Turn on the machine. a Press e (Back key). X The LCD comes on. Press b panel. (Settings key) on the operation X The initial screen appears again. X The settings
  • Brother International PE-700 | Users Manual - English - Page 84
    thread guide 8 M Brother poly #90 bobbin thread 7 buzzer 82 machine settings 21 , main power switch 9 19 C characters 52 maintenance 70 manual needle threading 34 , memory key 11 63 cleaning 70 cleaning brush 6 N D dust cover 6 E , embroidery card 7 55 embroidery card slot
  • Brother International PE-700 | Users Manual - English - Page 85
    65 S safety instructions 1 scissors 6 screwdriver 6 seam ripper 6 , settings key 11 22 spool cap guide cover 8 thread guide disk 9 thread guide plate 8 thread take-up lever check window 8 thread tension adjustment 64 top cover 8 touch panel 11 troubleshooting 74 turning machine
  • Brother International PE-700 | Users Manual - English - Page 86
    English 882-U30 XD1628-051 Printed in Taiwan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Computerized Embroidery Machine
Operation Manual
GETTING READY
EMBROIDERY
APPENDIX