Brother International RH-9820 Basic Instruction Manual - English
Brother International RH-9820 Manual
View all Brother International RH-9820 manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International RH-9820 manual content summary:
- Brother International RH-9820 | Basic Instruction Manual - English - Page 1
RH-9820 Basic Operation Manual ELECTRONIC EYELET BUTTON HOLER Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. This basic operation manual describes basic operations including sewing machine operations. For cleaning, standard - Brother International RH-9820 | Basic Instruction Manual - English - Page 2
much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explanations given in the instruction manual. With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such as the needle - Brother International RH-9820 | Basic Instruction Manual - English - Page 3
indications and their meanings This instruction manual and the indications and symbols that are used on the machine itself are provided in order to ensure safe operation of this machine and to prevent accidents and example, the symbol at left means "you must make the ground connection".) RH-9820 i - Brother International RH-9820 | Basic Instruction Manual - English - Page 4
problems with correct operation. Installation Machine installation should only be carried out by a qualified technician. Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. The sewing machine the oil out of the reach of children. ii RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 5
sewing, as this may result in personal injury or damage to the machine. If an error occurs in machine operation, or if abnormal noises or smells are noticed, immediately turn off the power switch. Then contact your nearest Brother dealer or a qualified technician. If the machine develops a problem - Brother International RH-9820 | Basic Instruction Manual - English - Page 6
Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer. 1 2 3 Do not touch the knife or press - Brother International RH-9820 | Basic Instruction Manual - English - Page 7
0332B Belt cover (Rear) 0331B 0333B 0486B 0334B RH-9820 0485B v - Brother International RH-9820 | Basic Instruction Manual - English - Page 8
the sewing machine 37 6-3. Program setting method 38 6-3-1. Parameter list 40 6-4. Checking the sewing SEWING MACHINE (SEWING OPERATION 50 7-1. Automatic sewing (automatic mode)..........50 7-2. Using the STOP switch 51 7-2-1. Pausing sewing during automatic sewing 51 Document CD 54 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 9
because the sewing machine will not start even if the start switch is pressed. (2) STOP switch + REET key (1) Speedy sewing in automatic mode (3) Accurate checking of lower thread trimming operation during manual mode RH-9820 3787M 3788M - Brother International RH-9820 | Basic Instruction Manual - English - Page 10
2. NAMES OF MAJOR PARTS 2. NAMES OF MAJOR PARTS 0335B The accessory switches shown below to use for starting the sewing machine will vary depending on the pulley (11) Feed base (12) Cotton stand (16) Needle guide cover (17) Belt cover *: CFTM is a trademark of SanDisk Corporation. RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 11
3. SEWING SHAPES Eyelet buttonhole 3. SEWING SHAPES Without bartack Taper bartack Straight bartack Straight buttonhole Round bartack Without bartack Circular stitch Taper bartack Straight bartack Round bartack RH-9820 0536B-0539B 0540B-0543B 0544B 3 - Brother International RH-9820 | Basic Instruction Manual - English - Page 12
Brother dealer or a qualified electrician for any electrical work that may need to be done. The sewing machine weighs approximately 120 kg. Installation of the sewing machine to the sewing machine may result. All cords should be secured at least 25 mm away from any moving parts. Furthermore, do - Brother International RH-9820 | Basic Instruction Manual - English - Page 13
2 x 2 mm dia. 10 depth (from underneath table) For power switch For table leg For bed base For provisionally holding bed base Melamine veneer panel 0338B RH-9820 5 - Brother International RH-9820 | Basic Instruction Manual - English - Page 14
place of purchase for further details. NOTE: When embedding the machine head into the table, be sure to install the L-shaped 20 depth (From underneath table) For valve unit For cotton stand For table leg For bed support plate Shaded area should be C10 For operation panel 4 x 2 mm dia. 10 depth - Brother International RH-9820 | Basic Instruction Manual - English - Page 15
control box (1), check that the model plate (2) on the control box (1) is "RX9820" to indicate that it is an RX-control box for RH-9820 sewing machines. (1) Control box (3) Bolts [4 pcs.] (4) Plain washers [4 pcs.] (5) Nuts [8 pcs.] NOTE: Check that the control box (1) is at least 10 mm away from - Brother International RH-9820 | Basic Instruction Manual - English - Page 16
the machine head, install the three treadle mounting bolts (A) to the table. * Insert the bolts (A) securely so that their heads do not protrude out from the top of the table. (Refer to "4-12. Installing the treadle unit (when using the treadle)".) Table 0343B (Continued on next page) 8 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 17
the machine head onto the table, have four or more people hold the machine head by the places indicated by the four locations in the illustration. • Do not hold by the head support lever are needed when moving the machine head, so store them in a safe place. gap Provisionally secure RH-9820 9 - Brother International RH-9820 | Basic Instruction Manual - English - Page 18
[4 pcs.] (5) Bolts [4 pcs.] (6) Washers (large) [4 pcs.] (7) Nuts [4 pcs.] After installing the machine head, remove the fixing bolts (8) and washers (9). NOTE: The fixing bolts (8) and washers (9) are needed when moving the machine head, so store them in a safe place. 0348B 0349B 10 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 19
will lock onto section A. 2. To return the machine head from the first step: After gently lifting up the machine head, remove the head support lever (4) from section A of the hinge support shaft (5), and then hold the bed at both sides and gently return it to its original position. RH-9820 11 - Brother International RH-9820 | Basic Instruction Manual - English - Page 20
The oiler should be installed while the machine head is tilted back. (Refer to "4-5. Tilting back and returning the machine head".) (1) Dust oiler support (2) Screws [2 pcs.] (3) Oiler (4) break. • Once installation is complete, return the machine head to its original position. 0354B 12 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 21
the far left of the table when looking from the front of the sewing machine. * Do not use the thread guide (1) which is provided a an accessory with the cotton stand. (2) the instruction manual CD "4-5. Threading the thread when the cotton stand is installed on the right side".) 0357B RH-9820 13 - Brother International RH-9820 | Basic Instruction Manual - English - Page 22
not touch the table leg. • Be careful to avoid injury from items such as sewing machine parts and the corners of table drawers during installation. 0358B 4-11. Installing the 2-pedal foot side) is depressed, the sewing machine will start. Work clamp switch Start switch 0361B 4923Q 14 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 23
, the work clamp will be lowered, and when it is depressed to the 2nd step, the sewing machine will start. 1st step 2nd step 4441Q 0359B 4-12-2. When embedding into the table (1) Treadle is depressed to the 2nd step, the sewing machine will start. 1st step 2nd step 4441Q 0360B RH-9820 15 - Brother International RH-9820 | Basic Instruction Manual - English - Page 24
> When the work clamp switch (left side) is depressed, the work clamp will be lowered, and when the start switch (right side) is depressed, the sewing machine will start. [When embedding into the table] 0363B Start switch Work clamp switch 0364B 0385B (Continued on next page) 16 - Brother International RH-9820 | Basic Instruction Manual - English - Page 25
loosened, the hand start switch (1) can be moved forward, back and sideways to adjust its position. Once adjustment is complete, securely tighten the screws (8). 0312B RH-9820 17 - Brother International RH-9820 | Basic Instruction Manual - English - Page 26
box 0365B 1. Remove the eight screws (1), and then remove the control box cover (2). 2. Gently tilt back the machine head. 3. Pass the cord bundle through the table hole, and then pass it into the control box through not to pull on the connectors. 0524B (Continued on next page) 18 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 27
switch, hand start switch 10-pin Operation panel 8-pin Hammer position sensor Machine head safety switch 3-pin (Y home position, cooling fan) sensor 12-pin P10 (SENSOR2) P12 (AIR1) P25 (AIR2) Cord clamp (5) (5) (5) (5) (5) (6) (6) (6) (6) (6) (7), (8) (7), (8) RH-9820 (Continued on next page) 19 - Brother International RH-9820 | Basic Instruction Manual - English - Page 28
to make the ground connection. (Refer to "4-14-2. Connecting the ground wire".) Connectors Machine head memory 7-pin Upper shaft motor 3-pin Synchronizer 14-pin Connectors θ-feed motor 4-pin motor harnesses so that they do not touch the PMD P.C. board. 0367B (Continued on next page) 20 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 29
not get pulled too tightly inside the control box. • Securely close the cord presser plate (9). If dust gets inside the control box, it may cause problems with operation. 7. Check that the cords do not get pulled, and then gently return the machine head to its original position. RH-9820 21 - Brother International RH-9820 | Basic Instruction Manual - English - Page 30
a serious electric shock, and problems with correct operation may also occur. 0369B (1) Ground wire from upper shaft motor harness (2) Ground wire from the machine head (3) Ground wire from foot to those mentioned above. Refer to the CE instruction manual for further details. 0336B 22 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 31
into a properly-grounded AC power supply. * The inside of the control box uses single-phase power. NOTE: Do not use extension cords. They may cause problems with correct operation of the sewing machine. Green/yellow wire (Ground wire) 0371B RH-9820 23 - Brother International RH-9820 | Basic Instruction Manual - English - Page 32
result. 1. Insert air tube No. 1 coming from the machine head into the nipple for the air unit assembly (1). (The numbers appear on the air tubes coming from the sewing machine. ) 2. Insert accessory air tube No. 5 and No (small) (3) to the underside of the table with the screw (4). 0373B RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 33
the cock (5). Air will enter the bowl and the pointer will move. 5. Repeat steps 1 to 4 until the desired air pressure is obtained. Close Open 0376B RH-9820 25 - Brother International RH-9820 | Basic Instruction Manual - English - Page 34
4. INSTALLATION 4-17. Installing the eye guard CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attached, injury may result. (1) Eye guard assembly (2) Plain washers and the scraps will collect inside the knife base. 0379B 26 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 35
Turn the upper shaft pulley (1) forward to align the mating mark (A) on the pulley with the notch (B) in the machine head. * The needle will be set to the needle up stop position. 2. Move the feed base (2) forward. > Install by carrying out the "Removal" procedure given above in reverse. RH-9820 27 - Brother International RH-9820 | Basic Instruction Manual - English - Page 36
, be sure to add more lubricating oil. If this is not done, problems such as seizing may occur. • Be careful not to add too much lubricating oil. If too much lubricating oil is added, it may overflow inside the sewing machine. 1. Tilt back the - Brother International RH-9820 | Basic Instruction Manual - English - Page 37
-use, lubricate the sewing machine in the places indicated by arrows in the illustration below. • Oil may get onto the thread while lubrication is being carried out. Carry out a test sewing to ensure that your by the arrows. 4. Once lubrication is complete, install the work clamp plates. RH-9820 29 - Brother International RH-9820 | Basic Instruction Manual - English - Page 38
5. PREPARATION BEFORE SEWING 5. PREPARATION BEFORE SEWING 5-1. Installing the needle CAUTION Turn off the power switch before installing the needle. Otherwise the machine may operate if the start switch is pressed by DO x 558 80 - 120 Nm (Schmetz 558) (Seen from the front) 0395B 30 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 39
5. PREPARATION BEFORE SEWING 5-2. Threading the upper side, the threading method will be different. Before threading, refer to the instruction manual CD "4-5. Threading the threads when the cotton stand is installed on the right for inserting the threader.) Upper thread 0396B RH-9820 0398B 31 - Brother International RH-9820 | Basic Instruction Manual - English - Page 40
PREPARATION BEFORE SEWING 5-3. the threading method will be different. Before threading, refer to the instruction manual CD "4-5. Threading the threads when the cotton stand is installed on the details on using the threader.) 0400B 32 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 41
SEWING , refer to the instruction manual CD "4-5. Threading the 00 specifications> Gimp should be clamped (when using about #8 spun thread or finer as the gimp) Gimp should be clamped Gimp should not be clamped (when using a thicker gimp) RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 42
1. Loosen the screws (3) at the left and right, and then move the cloth guides (2) forward or back to adjust the sewing margin . * can be adjusted to between 10 - 30 mm. 2. Once adjustment is complete, securely tighten the screws (3). - Brother International RH-9820 | Basic Instruction Manual - English - Page 43
SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) 6-1. Name and function of each operation panel item 0406B (1) Power indicator Illuminates when the power is turned on. (2) CAUTION indicator Illuminates when an error Illuminates when the material setting position is set to "front". RH-9820 35 - Brother International RH-9820 | Basic Instruction Manual - English - Page 44
SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) 0406B (18) BEFORE key This key is used to set cutting operation to cutting before sewing. (19) BEFORE indicator Illuminates when cutting operation is set to cutting before sewing . (35) Display This shows program numbers and messages. 36 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 45
the ON side. [The display examples are for a -01 specification sewing machine.] The power indicator (2) will illuminate and the contents the mode (automatic mode, manual mode, test mode, cycle program mode or program mode) that was active when the sewing machine was last turned off. . RH-9820 37 - Brother International RH-9820 | Basic Instruction Manual - English - Page 46
SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) 6-3. Program setting method It is recommended that you register patterns that are sewn frequently as programs. After programs have been registered, you can retrieve the desired sewing program (Refer to the instruction manual CD) (1) 0413B 3 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 47
Sewing length (Parameter No. 02) (6) Cutting spacing (Parameter No. 03) (7) Stitch pitch (Parameter No. 04) (8) No. of eyelet stitches (Parameter No. 05) (9) Bartack length (Parameter Nos. 06, 08, 10)* *: Loads the parameter number corresponding to the bartack shape for parameter No. 40. RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 48
SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) 6-3-1. Parameter list NOTE: It may not be possible to change some setting values or some settings may be invalid because of the settings for other parameters. No. Setting 01 Sewing : 25 mm : 25 mm - Brother International RH-9820 | Basic Instruction Manual - English - Page 49
6. USING THE SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) No. Setting 09 No. of straight bartack stitches Setting range 5 - 18 stitches Unit 1 Initial value 7 stitches 10 No. of round bartack stitches 5 - 17 stitches 1 7 stitches 11 Eyelet pattern 12 Zigzag width adjustment 1 - 6 1 - Brother International RH-9820 | Basic Instruction Manual - English - Page 50
at the sewing 0 - 2 stitches start 20 No. of tying stitches at the sewing end 0 - 2 stitches 21 X correction value -1 - 6 22 Y correction value 23 θ 1 correction value 24 θ 2 correction value -1 - 6 -3 - 3 -3 - 3 1 0 stitches 1 0 stitches 1 0 1 0 1 0 1 0 0284B - 0291B 42 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 51
No. Setting 25 Taper bartack angle 6. USING THE SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) -5 - 5 Setting range Unit 1 Initial value 0 26 Straight bartack width correction -1.0 - 0.0 1 0 1 stitch 33 Spare (For future version upgrades) 0292B - 0294B 0471B 0295B 0297B RH-9820 43 - Brother International RH-9820 | Basic Instruction Manual - English - Page 52
6. USING THE SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) No. Setting 34 Circular stitch knife size Setting range 2 - 5 mm Unit 1 Initial value 2 copy source) 40 Bartack shape 1: Without bartack 1 2: Taper bartack 3: Straight bartack 4: Round bartack OFF 2 0298B - 0301B 44 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 53
sewing shape (1), program number (2), total number of stitches (3) and number of remaining stitches (4) will appear in the display. 0230B Independent program (Refer to P. 38) Cycle program (Refer to the instruction manual will not be carried out in test mode. (Continued on next page) RH-9820 45 - Brother International RH-9820 | Basic Instruction Manual - English - Page 54
SEWING MACHINE (OPERATION PANEL: BASIC OPERATION) 6 [If you would like to pause test feeding and return the feed base to the material setting position] Press the STOP switch (7) and then press the RESET key. [If you would like to return the feed base to the previous sewing [Once sewing continues to - Brother International RH-9820 | Basic Instruction Manual - English - Page 55
cutting after sewing is selected, the cutting after sewing indicator illuminates. Press the BEFORE or AFTER key during the standby condition in automatic mode, test mode or manual mode. The cutting operation changes as shown in the illustration each time a key is pressed. 0308B 0309B RH-9820 47 - Brother International RH-9820 | Basic Instruction Manual - English - Page 56
mode or manual mode. The feed base will move forward (to the sewing start position). 0426B [To move the feed base backward (standard material setting position)] Press the FRONT/BACK key once more. 0427B The feed base will move backward (to the standard material setting position). 48 RH-9820 - Brother International RH-9820 | Basic Instruction Manual - English - Page 57
upper thread easier. In addition, threading mode is safe because the sewing machine will not operate when the start switch is pressed (or the the THREAD key during the standby condition in automatic mode, test mode or manual mode. • The tension discs will open. • The buzzer will sound, RH-9820 49 - Brother International RH-9820 | Basic Instruction Manual - English - Page 58
result in serious injury. • When replacing the needle • When not using the sewing machine and when leaving the sewing machine unattended Do not touch any of the moving parts or press any objects against the sewing machine while sewing. If this is not observed, it may result in personal injury or - Brother International RH-9820 | Basic Instruction Manual - English - Page 59
Using the STOP switch 7-2-1. Pausing sewing during automatic sewing The STOP switch is used to stop the sewing machine if a problem occurs such as a thread breakage. Press the STOP switch (1) while sewing is being carried out. 0436B The sewing machine will stop and the buzzer will - Brother International RH-9820 | Basic Instruction Manual - English - Page 60
7. USING THE SEWING MACHINE (SEWING OPERATION) 1 Press the RESET key. 0437B The buzzer will stop sounding. (The display will change alternately.) 0438B 2 Eliminate the cause of the problem. * If a problem such as an - Brother International RH-9820 | Basic Instruction Manual - English - Page 61
MEMO RH-9820 53 - Brother International RH-9820 | Basic Instruction Manual - English - Page 62
documents are contained in PDF format. ・ Basic Operation Manual ・ Instruction Manual ・ Parts Book How to use the Windows® 2000 Service Pack 4, Windows® XP Service Pack 2 Microsoft® Internet Explorer 6 Service Pack 1 brother.com/ © 2006 Brother Industries, Ltd. All Rights Reserved. RH-9820 SA7886-001 E
RH-9820
ELECTRONIC EYELET BUTTON HOLER
Please read this manual before using the machine.
Please keep this manual within easy reach for quick reference.
This
basic
operation
manual
describes
basic
operations including sewing machine operations.
For cleaning, standard adjustments and more details,
please refer to the instruction manual contained in
the Document CD.
Basic Operation Manual