Canon 3801B002 User Manual

Canon 3801B002 Manual

Get Canon 3801B002 PDF manuals and user guides View all Canon 3801B002 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon 3801B002 manual content summary:

  • Canon 3801B002 | User Manual - Page 1
    User Manual Please read this manual before operating this scanner. After you finish reading this manual, store it in a safe place for future reference.
  • Canon 3801B002 | User Manual - Page 2
    Document Scanner. DR-6010C: Model M11072 Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • imageFORMULA is a trademark of CANON ELECTRONICS INC. • Microsoft, Windows and Windows
  • Canon 3801B002 | User Manual - Page 3
    jam Chapter 4 Maintenance Procedures for regular maintenance, roller replacement Chapter 5 Troubleshooting Troubleshooting information, application uninstall procedure Chapter 6 Appendix Product specifications and dimensional drawings Software Chapter 7 ISIS/TWAIN Driver Settings ISIS/TWAIN driver
  • Canon 3801B002 | User Manual - Page 4
    symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety explanations for a procedure. Reading these notes is highly recommended. (See "Documents," on p. 3-1) Shows the page number and title of a section that
  • Canon 3801B002 | User Manual - Page 5
    User Manual Hardware
  • Canon 3801B002 | User Manual - Page 6
    Safety Instructions 1-1 Installation Location 1-1 Power ...1-2 Moving the Scanner 1-2 Handling ...1-3 Disposal...1-4 Features of the DR-6010C Document Scanner 1-5 Names and Functions of Parts 1-7 Setup ...2-1 Setup Procedure 2-1 Installation Requirements 2-2 Installing the Software 2-4 Setup
  • Canon 3801B002 | User Manual - Page 7
    Retard Roller 4-11 Troubleshooting 5-1 Troubleshooting 5-1 Uninstalling Software 5-6 Uninstalling the ISIS/TWAIN Driver 5-7 Uninstalling the Job Registration Tool 5-8 Uninstalling CapturePerfect 3.0 5-10 Appendix ...6-1 Specifications 6-1 Specifications 6-1 Replacement Parts 6-2 Options
  • Canon 3801B002 | User Manual - Page 8
    .6" (650 mm) when the document feed tray and document feed tray extension are open. • If scanned documents are ejected to the back tray of the scanner, provide adequate space behind the scanner for documents ejected after being scanned. (See "Preparing the Document Eject Tray," on p. 3-3.) • Avoid
  • Canon 3801B002 | User Manual - Page 9
    the scanner. This may result in a noticeable degradation in scanning quality. The following conditions are recommended for optimal scanning quality: Room local authorized Canon dealer or service representative for further information. Moving the Scanner • When moving the scanner, always hold
  • Canon 3801B002 | User Manual - Page 10
    power switch OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced. ■ Before moving the scanner, be sure to turn the power switch OFF, and disconnect the power plug from the power outlet. CAUTION
  • Canon 3801B002 | User Manual - Page 11
    injury. Be extra careful of neckties and long hair. If anything becomes caught in the scanner, immediately disconnect the power cord to stop the scanner. ■ Be careful when placing paper in the scanner and when removing jammed paper. It is possible to cut your hand on the edge of a sheet of paper
  • Canon 3801B002 | User Manual - Page 12
    features of the DR-6010C document scanner are described below. • Fast Document Feeding The scanner can scan a maximum of 60 documents per minute in a range of sizes from business cards to LTR/A4 size. (Scanning conditions: Black and white, LTR/A4 size portrait, 200 dpi.) Scanning speed is the same
  • Canon 3801B002 | User Manual - Page 13
    adjusted image to the application software, without needing to scan the document again. • Remove Binder Holes This mode erases the black spots that appear on scanned images from binding holes on the original document. • MultiStream Function The scanner supports MultiStream, which, according to the
  • Canon 3801B002 | User Manual - Page 14
    the parts of the scanner before using the scanner. ■ Front View (Feed Tray Open) Document Eject Tray Extension Open if the document extends beyond the edge of the eject tray. (See p. 3-3.) Document Feed Tray Place the document to be scanned here. (See p. 3-3.) Document Eject Tray Scanned documents
  • Canon 3801B002 | User Manual - Page 15
    Scanner ■ Back View Document Eject Tray 2 Open this tray to use the scanner in a straight path configuration. (See p. 3-3.) ■ Interfaces (See "2-4 Connecting the Scanner supports Hi-Speed USB 2.0. Power Connector CAUTION • Do not block the ventilation openings. Doing so could cause the scanner
  • Canon 3801B002 | User Manual - Page 16
    order to prepare the scanner for use, read and follow the instructions in each section below. Installation Requirements Installing the Software Connecting the Scanner to the Computer Turning the Power ON IMPORTANT • Be sure to install the software before connecting the scanner to the computer. • If
  • Canon 3801B002 | User Manual - Page 17
    Installation Requirements To use the DR-6010C scanner, your computer must satisfy the following system requirements. • One of the following operating systems: - Microsoft Windows 2000 Professional SP4 or later - Microsoft Windows XP Professional SP3 or later - Microsoft Windows XP Home Edition SP3
  • Canon 3801B002 | User Manual - Page 18
    the computer satisfies the recommended specifications, the scanning speed may vary, depending on the scan settings. • The ISIS/TWAIN Drivers provided with the scanner do not necessarily operate on all ISISor TWAIN-compatible applications. For details, contact your application software retailer. 2-3
  • Canon 3801B002 | User Manual - Page 19
    Note The Setup disc of the DR-6010C is configured as follows. Menu screen Typical Installation Read Manuals All of the indicated software is installed. Custom Installation The User Manual and CapturePerfect 3.0 Operation Guide electronic manuals for the scanner are installed on the computer
  • Canon 3801B002 | User Manual - Page 20
    all of the displayed software and the User Manual will be installed automatically. If you want to reinstall only specific software that you have previously uninstalled, select [Custom Installation] and specify the software. • The DR-6010C driver installation comprises the Scanner Driver and Job Tool
  • Canon 3801B002 | User Manual - Page 21
    Chapter 2 Setup 4 Click [Install]. Installation of the DR-6010C driver begins. 5 Click [Next]. The software license agreement appears. 6 Read the license agreement and click [Yes] to accept it. The DR-6010C driver is installed. 2-6
  • Canon 3801B002 | User Manual - Page 22
    Chapter 2 Setup Next, the job tool software is installed. 7 The DR-6010C driver installation is complete. 8 Click [Finish]. Installation of CapturePerfect 3.0 starts. 2-7
  • Canon 3801B002 | User Manual - Page 23
    Chapter 2 Setup 9 Click [Next]. The software license agreement appears. 10 Read the license agreement and click [Yes] to accept it. The installation location screen appears. 11 Click [Next]. CapturePerfect is installed. 12 The CapturePerfect installation is complete. 2-8
  • Canon 3801B002 | User Manual - Page 24
    Chapter 2 Setup 13 Click [Finish]. Installation of the User Manual starts. 14 Click [Next]. The User Manual is installed. 15 The User Manual installation is complete. 16 Click [Finish]. The installation completion screen appears. 2-9
  • Canon 3801B002 | User Manual - Page 25
    Chapter 2 Setup 17 Click [Exit]. Click [Back] to return to the menu screen. 18 After the software installation is complete, you can connect the scanner to the computer. (See "2-4 Connecting the Scanner to the Computer," on p. 2-11.) 2-10
  • Canon 3801B002 | User Manual - Page 26
    to the Computer There are two methods for connecting the DR-6010C scanner to a computer: USB connection, which makes use of a SCSI cable at the same time. Using a USB Connection 1 Verify that the power switch of the scanner is OFF. If the power switch is in the ON position, push the switch to set it
  • Canon 3801B002 | User Manual - Page 27
    ID numbers in the system. DIP switches Factory default (SCSI ID = 2) • The DR-6010C scanner incorporates a SCSI terminator which is permanently set to ON. When using a daisy-chain configuration with other SCSI devices, make sure that the DR6010C is connected as the last device in the chain. Set the
  • Canon 3801B002 | User Manual - Page 28
    Chapter 2 Setup 1 Shut down Windows and turn the computer OFF. 2 Verify that the power switch of the scanner is OFF. If the power switch is in the ON position, push the switch to V Type 4 Connect the power cord into an AC outlet. b 5 Use the SCSI cable to connect the scanner to the computer. 2-13
  • Canon 3801B002 | User Manual - Page 29
    the scanner ON. The power indicator lights green. Power indicator Power switch ON 3 Turn the computer ON. 4 Log onto Windows with an account that has Administrator privileges. 5 Windows recognizes the DR-6010C automatically, and installation of the device driver begins. Windows Vista Windows
  • Canon 3801B002 | User Manual - Page 30
    Chapter 2 Setup Note • In Windows Vista and Windows XP, a message appears when installation is complete. • In Windows 2000, no message appears when installation is complete. • The DR-6010C is installed in Device Manager under [Imaging Devices] as [CANON DR- 6010C USB] or [CANON DR-6010C SCSI]. 2-15
  • Canon 3801B002 | User Manual - Page 31
    66 mm) Can be scanned Size: 2.12" × 3.37" (53.9 mm × 85.5 mm) Thickness: 0.03" ± 0.003" (0.76 ± 0.08 mm) without embossing (*1) The DR-6010C offers two document eject configurations: U-turn path (the document is ejected to the document eject tray at the front of the scanner) and straight path (the
  • Canon 3801B002 | User Manual - Page 32
    cause the scanner to jam. • Scanning documents before the ink is dry can cause problems with the scanner. Always make sure that the ink on a document is dry before scanning it. • Scanning documents that are written in pencil or similar material have a tendency to make the rollers and scanning glass
  • Canon 3801B002 | User Manual - Page 33
    it toward you. If the documents slide off the tray, pull out the document feed tray extension. Document Feed Tray Document Feed Tray Extension CAUTION Do not place anything other than documents on the document feed tray. Doing so may damage the scanner, reduce scanning quality, or cause the tray to
  • Canon 3801B002 | User Manual - Page 34
    occur. • Open or close the document eject tray 2 before starting to scan documents. Opening or closing the document eject tray 2 while scanning may cause a paper jam. • When using the U-turn path, make sure to open the eject tray guide. If the guide is not opened, documents may fall off the tray and
  • Canon 3801B002 | User Manual - Page 35
    happens, scan the document in the bypass mode. CAUTION ■ Before you place a document, check to make sure it does not contain paper clips, staples, or other small metal objects. These items may cause a fire or electrical shock, damage the document, or cause a paper jam or scanner malfunction. ■ Do
  • Canon 3801B002 | User Manual - Page 36
    on top of the scanner to align them. Doing so may cause a malfunction. ■ When placing documents into the feed tray, take care not to cut your hands on the edges of the paper. 3 Adjust the document guides so that they are wider than the document to be scanned. 4 Place the document face up into the
  • Canon 3801B002 | User Manual - Page 37
    feed tray correctly. Scanning an improperly placed, curled, or creased document may damage the document or cause a paper jam. 6 Start scanning. IMPORTANT • If feeding stops due to a system error or paper jam while the scanner is scanning, resolve the problem, make sure that the scanned image of the
  • Canon 3801B002 | User Manual - Page 38
    leading edge of the documents as you feed them. Take care not to get your hand caught under the roller unit, as this may cause personal injury. Roller Unit ■ After you finish scanning, close the document feed tray and the document eject tray extension to prevent damage to the scanner while it is not
  • Canon 3801B002 | User Manual - Page 39
    Operation 3-4 Job Function In addition to using scanning applications, such as Capture Perfect 3.0 to perform scanning, the DR6010C is equipped with the Job Function. The Job Function enables you to scan simply by touching a job button on the scanner. This section provides an overview of the Job
  • Canon 3801B002 | User Manual - Page 40
    settings. b Stop: Stops scanning. c Save as file: Saves scanned image data as PDF files in the [Pictures] folder. • If you assign scan functions to all three job buttons on the scanner, use the Start and Stop buttons on the Scan Panel to start or stop scanning. (See "Scan Panel," on p. 3-21
  • Canon 3801B002 | User Manual - Page 41
    complete> appears on the DR-6010C monitor. 4 Click [Close] to close the DR-6010C monitor. Note • The default setting for job button c after the DR-6010C setup is completed is "Scan." • The scanned images are saved as PDF files in the folder [Pictures] under the folder [Documents]. The file name is
  • Canon 3801B002 | User Manual - Page 42
    from this dialog box or click [Cancel] and change the event settings. • Only applications that support the Windows event function can be started using the Launcher feature of the DR-6010C. • Some applications may not work correctly if started using the Launcher feature. Event Settings This section
  • Canon 3801B002 | User Manual - Page 43
    Chapter 3 Basic Operation 2. Click [Hardware and Sound]. Note Under Windows XP, click [Printers and Other Hardware]. 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 3-13
  • Canon 3801B002 | User Manual - Page 44
    Chapter 3 Basic Operation 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears. 5. Click the [Events] tab. 2 Under [Scanner events], select the button whose setting you want to change (
  • Canon 3801B002 | User Manual - Page 45
    device events] check box is selected, the Job Function cannot be used. Make sure that this check box is not selected. 4 Click [OK] to close [CANON DR-6010C USB Properties]. 5 Restart Windows to enable the new event settings. 3-15
  • Canon 3801B002 | User Manual - Page 46
    is an ISIS-compatible application developed for Canon document scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Scan menu to perform scanning. „ Scan Batch to File Documents are scanned with the preset scanning conditions, and the scanned image data
  • Canon 3801B002 | User Manual - Page 47
    when the scanner is used in environments, such as conference halls, where it can be connected to large displays or projectors. CapturePerfect 3.0 is switched to full-screen display, the document is scanned, and the scanned image is displayed at full size on the screen. DR-6010C Projector The
  • Canon 3801B002 | User Manual - Page 48
    Windows [Start] button Æ click [Programs] ([All Programs] for Windows XP) Æ [CapturePerfect 3.0] Æ [CapturePerfect 3.0]. CapturePerfect 3.0 starts up. 2 Follow the procedure below to select the Canon DR-6010C Document Scanner as the scanner to be used. 1. On the [Scan] menu, click [Select Scanner
  • Canon 3801B002 | User Manual - Page 49
    the ISIS/TWAIN driver. (See "2-3 Installing the Software," on p. 2-4.) 3. Set the Default Page Size and click [OK]. Note This dialog box is displayed only when you select [Canon DR-6010C] for the first time and click [OK], or when you click [Setup] for [Scanner Selection]. 3 On the [Scan] menu
  • Canon 3801B002 | User Manual - Page 50
    Chapter 7, "ISIS/TWAIN Driver Settings." 5 Place your document. (See "3-3 Placing Documents," on p. 3-5.) 6 On the [Scan] menu, select [Scan Batch to File]. The [Scan Batch to File Setting] dialog box opens. For more details on how to scan documents, see the CapturePerfect 3.0 Operation Guide and
  • Canon 3801B002 | User Manual - Page 51
    [Exit] on the [File] menu to quit CapturePerfect 3.0. Scan Panel The Scan Panel is an application that is installed with the ISIS/TWAIN driver. When the DR-6010C driver starts, the scan panel appears in the task tray. If Feeding Option in the scan settings is set to "Panel-Feeding" or "Automatic
  • Canon 3801B002 | User Manual - Page 52
    , this button becomes active when scanning of the current document completes, and scanning stops. When clicked, this button depresses and remains depressed while scanning with batch separation continues, until scanning of the current document completes, and scanning stops. The button then returns
  • Canon 3801B002 | User Manual - Page 53
    . Click on the Windows start button, open [Programs] Æ [Canon DR-6010C] Æ [PATCH X (XX)]. Print the patchcode sheet to use it for scanning. Note To open patchcode sheets you need CapturePerfect 3.0, which is provided with the scanner, or an application, which supports PDF format files. IMPORTANT
  • Canon 3801B002 | User Manual - Page 54
    . Extremely dark or light copies may not be scanned correctly. 2 Insert the patchcode sheet in front of the document that you want to save as a separate file before placing the documents on the scanner. Insert patchcode sheets in front of the documents you want to save as separate files. 3-24
  • Canon 3801B002 | User Manual - Page 55
    [Other] tab of the ISIS driver properties, set the batch separation setting to "Patchcode." 4 From the application, perform scanning with batch separation enabled. Note If you are scanning with CapturePerfect, set the Type of batch separation setting to "Scan, Continue Scanning" or "Skip, Continue
  • Canon 3801B002 | User Manual - Page 56
    Jam When paper jams occur during scanning, use the following procedure to clear them. CAUTION When removing jammed paper, take care not to cut your hands on the edges of the paper. 1 Remove any documents that have been left in the eject tray, and close the eject tray guide. IMPORTANT If a document
  • Canon 3801B002 | User Manual - Page 57
    the document out carefully, without applying too much force. If jammed paper tears while it is being removed, make sure to remove any remaining pieces from inside the scanner. may damage the scanner. Note • After removing the jammed paper, check to see if the last page was scanned, and then continue
  • Canon 3801B002 | User Manual - Page 58
    3 Basic Operation • If a paper jam occurs when "Rapid recover system" is enabled in the ISIS/TWAIN driver settings, the image data of the document is not saved and scanning stops. This allows you to continue scanning from the document that caused the paper jam after the paper jam is fixed. 3-28
  • Canon 3801B002 | User Manual - Page 59
    The DR-6010C will scan both sides and combine the scanned images into a single image. Front Rear Combined image • To use this function, select Folio as the "Scanning Side" setting. For details, see Chapter 7, "ISIS/TWAIN Driver Settings." • The scanned image of the front side of the document becomes
  • Canon 3801B002 | User Manual - Page 60
    a maximum of 39.2" (1,000 mm) long. (See "Long Document Mode Settings," on p. 3-31.) IMPORTANT When scanning in the Long Document mode, set the paper size for the ISIS/TWAIN driver to "Auto-detection" to allow the scanner to detect and scan documents up to 39.2" (1,000 mm) long. Note the following
  • Canon 3801B002 | User Manual - Page 61
    avoid paper jams. • When scanning long documents, make sure to feed them one page at a time with the bypass mode. Long Document Mode Settings Follow the procedure below to set the Long Document mode. 1 Use the following procedure to open the [CANON DR-6010C USB Properties] (or [CANON DR-6010C SCSI
  • Canon 3801B002 | User Manual - Page 62
    Chapter 3 Basic Operation 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears. 3-32
  • Canon 3801B002 | User Manual - Page 63
    2 Click the [Maintenance] tab. 3 Click [Long Document mode (1,000 mm)]. 4 Click [OK] to close [CANON DR-6010C USB Properties]. 5 Turn the scanner OFF and then ON again. IMPORTANT • If you are using a SCSI connection, turn OFF the computer and then turn the scanner OFF and then ON again. • Wait at
  • Canon 3801B002 | User Manual - Page 64
    using supports the MultiStream function, then it is possible to scan a document once and simultaneously output two types of images (Primary image and Secondary image.) CapturePerfect 3.0 supports the when "Auto Color Detection" is selected for the Mode setting in the ISIS/TWAIN driver. 3-34
  • Canon 3801B002 | User Manual - Page 65
    scanning quality. CAUTION ■ When cleaning the scanner, turn OFF the power switch and disconnect the power cord from the power outlet. ■ Do not use excessive force when removing or attaching the rollers in the document feed opening or inside the scanner can cause lines in scanned images. Use compressed
  • Canon 3801B002 | User Manual - Page 66
    Chapter 4 Maintenance Cleaning the Sensor Glass and the Rollers If scanned images have extraneous marks, or if the scanned documents are dirty, the sensor glass or rollers inside the scanner may be dirty. Clean them periodically. 1 Carefully open the upper unit until it stops. IMPORTANT When opening
  • Canon 3801B002 | User Manual - Page 67
    glass, contact your local authorized Canon dealer or service representative. 4 Dampen a cloth with water, wring it out thoroughly, and then wipe the rollers of the upper unit while turning them. Do not try to turn the rollers in the lower part of the scanner. Clean these rollers simply by wiping the
  • Canon 3801B002 | User Manual - Page 68
    has been moistened with water and thoroughly wrung out. 7 Attach the rollers that were removed. (See "Attaching the Roller Unit," on p. 4-10, and "Attaching the Retard Roller," on p. 4-12.) 8 Make sure that the upper unit is Do not force the upper unit to close. Doing so may damage the scanner. 4-4
  • Canon 3801B002 | User Manual - Page 69
    in each respective section. IMPORTANT Feed rollers are consumable parts. When the rollers start to wear out, paper jams and misfeeds may occur more often. When this happens, purchase an exchange roller kit and replace the roller unit and the retard roller. CAUTION Do not use excessive force
  • Canon 3801B002 | User Manual - Page 70
    Maintenance Resetting the Counter After replacing the feed rollers, open the [Counter setup] dialog box and reset the counter. 1 Open the [Event settings] dialog box. 1. Click [Start] - [Control Panel] to open the Control Panel. Note Under Windows 2000, click the [Start] button and select [Settings
  • Canon 3801B002 | User Manual - Page 71
    Chapter 4 Maintenance 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears. 4-7
  • Canon 3801B002 | User Manual - Page 72
    Chapter 4 Maintenance 2 Click the [Maintenance] tab. 3 Click the [Reset] button, and then make sure that the counter for the roller being used is set to 0. 4-8
  • Canon 3801B002 | User Manual - Page 73
    unit until it stops. IMPORTANT When opening the upper unit, do not grasp the roller unit in the center. Doing so may distort the rollers and lead to feeding errors. 2 Push the roller lock lever down. 3 While supporting the roller unit with your hand, slide the roller lock lever to the right. 4-9
  • Canon 3801B002 | User Manual - Page 74
    the right a and then pull it out b. Attaching the Roller Unit 1 Align the cutout on the roller unit with the shaft pin on the main unit. Note If the cutout and pin do not fit, rotate the roller until the parts are properly matched. 2 Slide the roller lock lever to the left and raise the
  • Canon 3801B002 | User Manual - Page 75
    caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. Removing and Attaching the Retard Roller To remove or attach the retard roller, proceed as follows. CAUTION Do not use excessive force when removing or attaching the retard
  • Canon 3801B002 | User Manual - Page 76
    ends of the roller cover and remove the cover. 3 Move the roller lock lever down and forward (a,) and then slide it to the right (b.) 4 Shift the retard roller to the right to remove it. Attaching the Retard Roller 1 Position the retard roller so the notch in the roller is facing the scanner's shaft
  • Canon 3801B002 | User Manual - Page 77
    Chapter 4 Maintenance 2 Slide the roller lock lever to the left, and insert it into the retard roller slot. 3 Push the roller lock lever towards the back of the scanner to lock the retard roller into place. 4 Replace the roller cover. 5 Push the center of the roller cover down and make sure that it
  • Canon 3801B002 | User Manual - Page 78
    get your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. 4-14
  • Canon 3801B002 | User Manual - Page 79
    the scanner is switched ON. If the scanner is OFF, turn the scanner ON. (See p. 2-11.) Problem Solution The scanner does not support your USB interface. This product is not guaranteed to operate with all types of USB interfaces. Contact your local authorized Canon dealer or service representative
  • Canon 3801B002 | User Manual - Page 80
    SCSI card. (See p. 2-2.) ✘ Scanning Is Not Performed Check the following if the scanner does not scan an image even though the scanning operation is performed: • Has the application software been installed correctly? Has the application software been set up correctly? • Is there a problem in the PC
  • Canon 3801B002 | User Manual - Page 81
    5 Troubleshooting IMPORTANT • If documents are not scanned normally even if the scanner setup is OK, a probable cause is that the scanner driver or application software is not running correctly. Re-install the scanner driver or application software. • When system errors result in the scanner not
  • Canon 3801B002 | User Manual - Page 82
    ISIS/ TWAIN driver settings or a problem with the scanning unit inside the scanner. Scanning results can also become skewed if the ISIS/ TWAIN driver has not been installed correctly, or the application in use does not support ISIS/ TWAIN driver functions. Symptoms Problem Solution The scanned
  • Canon 3801B002 | User Manual - Page 83
    an angle. (skew) Use the document guide adapter to prevent document skew, and set [Deskew] to on. Symptoms Problem Solution Lines, smudges, or dirt appear on the scanned image. The scanning glass or rollers inside the scanner are dirty. Clean the scanning glass and rollers. (See p. 4-1.) If lines
  • Canon 3801B002 | User Manual - Page 84
    Chapter 5 Troubleshooting 5-2 Uninstalling Software If the ISIS/TWAIN driver, and "CapturePerfect 3.0" are not operating normally, follow the procedure below to uninstall them. Then, re-install the software from the DR-6010C setup disc. (See "2-3 Installing the Software," on p. 2-4.) IMPORTANT Be
  • Canon 3801B002 | User Manual - Page 85
    Chapter 5 Troubleshooting The [Uninstall or change a program] dialog box appears. Note For Windows XP, the [Add or Remove Programs] dialog 3.0," on p. 5-10. Uninstalling the ISIS/TWAIN Driver 1 From the Programs list in the dialog box, select [Canon DR-6010C Driver] Æ click [Uninstall]. 2 The confirm
  • Canon 3801B002 | User Manual - Page 86
    Chapter 5 Troubleshooting The uninstall procedure is carried out. 3 After uninstall is complete, click the [Finish] button to exit the uninstaller. Uninstalling the Job Registration Tool 1 From the Programs list in the dialog box, select [DR-6010C Job Tool] and click [Uninstall]. 5-8
  • Canon 3801B002 | User Manual - Page 87
    Chapter 5 Troubleshooting 2 The confirm file deletion screen appears. Click the [Yes] button. Note Under Windows XP, the [Add/Remove Programs] dialog box appears. 3 Click the [Yes] button. The uninstall procedure is carried out. 4 After uninstall is complete, click the [Finish]
  • Canon 3801B002 | User Manual - Page 88
    Chapter 5 Troubleshooting Uninstalling CapturePerfect 3.0 1 Select [CapturePerfect 3.0] from the list in the dialog box Æ click the [Uninstall] button. 2 The file delete confirmation screen appears. Click the [Yes] button. Uninstallation starts. 5-10
  • Canon 3801B002 | User Manual - Page 89
    Chapter 5 Troubleshooting 3 After uninstallation is complete, click the [Finish] button to exit the uninstaller. 5-11
  • Canon 3801B002 | User Manual - Page 90
    straight path bypass feed mode. Scanning embossed cards is not guaranteed. Document Feeding Method Automatic/Manual Scanning Method CMOS CIS 3-line sensor Light Source RGB LED Effective Scanning Width 236 mm Scanning Side Front/Back/Duplex Scanning Modes Black and white, Error diffusion
  • Canon 3801B002 | User Manual - Page 91
    information about replacing the rollers. • Contact your local authorized Canon dealer or service representative for detailed information about the replacement parts. Options Bar code module (product code: 1922B001) Additional software to allow the ISIS/TWAIN driver to recognize bar codes. Contact
  • Canon 3801B002 | User Manual - Page 92
    Chapter 6 Appendix External Dimensions 12.5" (318 mm) 10.9" (278 mm) 21.4" (544 mm) (Document Feed Tray Extension is open) 19.3" (491 mm) (Document Feed Tray is open) 12.9" (330 mm) (Document Eject Guide is open) 2.0" (51 mm) (Document Eject Tray 2 is open) 8.9" (225 mm) 5.2" (131 mm) 4.7" (119
  • Canon 3801B002 | User Manual - Page 93
    2-12 Disposal 1-4 document eject configurations 3-1 document feed tray 3-7 document guides 3-6 Documents 3-1 Double Feed Detection Function 3-30 DR-6010C monitor 3-11 E Eject Tray 3-3 event 3-12 Event settings 4-6 External Dimensions 6-3 F Features 1-5 Folio Scan 3-29 H Handling
  • Canon 3801B002 | User Manual - Page 94
    User Manual Software
  • Canon 3801B002 | User Manual - Page 95
    7-2 Chapter8 8-1 8-2 Chapter9 ISIS/TWAIN Driver Settings 7-1 Before Use 7-1 ISIS/TWAIN Driver Properties Dialog Box 7-3 Basic Scanning Both Sides of Pages 9-1 Scanning Non-Standard-Size Documents 9-1 Adjusting the Scan Area 9-2 Scanning Multiple Documents 9-3 Image Adjustments for Scanning
  • Canon 3801B002 | User Manual - Page 96
    ISIS and TWAIN drivers. Please read this chapter and the ISIS/TWAIN driver's Help before making driver settings. 7-1 Before Use This scanner can scan documents ranging in size from business cards and checks to A4 size documents. It can also scan business cards. To use the DR-6010C with an ISIS/TWAIN
  • Canon 3801B002 | User Manual - Page 97
    Chapter 7 ISIS/TWAIN Driver Settings 2 On the [Scan] menu, click [Select Scanner]. 3 Select [Canon DR-6010C] Æ click the [OK] button. Note If [Canon DR-6010C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. 4 Click the [Settings] button to set a default page size. Note •
  • Canon 3801B002 | User Manual - Page 98
    7 ISIS/TWAIN Driver Settings 7-2 ISIS/TWAIN Driver Properties Dialog Box The ISIS/TWAIN driver properties dialog box consists of four tabs: Basic, Brightness, Image processing and Others. See the description of each tab sheet for details. [OK] Button Applies settings and closes the dialog box. [Scan
  • Canon 3801B002 | User Manual - Page 99
    ) This [Basic] tab sheet is displayed when the DR-6010C ISIS Driver is called from a scanner setting or scanning dialog box belonging to an ISIS-compatible application program. This [Basic] tab sheet provides settings for DR-6010C functions that are not supported in the dialog box belonging to the
  • Canon 3801B002 | User Manual - Page 100
    ISIS/TWAIN Driver Settings ☞ Refer to the descriptions of the following function for details about "Skip Blank Page," "Auto Color Detection," "Detect Page Size," "Text Enhanced Enhancement Mode" and "Margin." • Skip Blank Page Æ [Scanning modes are good for scanning documents with a background
  • Canon 3801B002 | User Manual - Page 101
    background remains visible in the image, and text may be hard to read. [High-Speed Text Enhancement] This mode optimizes processing speed by performing background processing within the scanner, and is good for scanning documents with light background and dark text. ☞ If the text and background in
  • Canon 3801B002 | User Manual - Page 102
    -out Reverse Image (TWAIN driver) Prevent Bleed Through / Remove Background Border Removal Erase Dot Edge enphasis Moire Reduction Deskew Scanning mode Black and White ✓ Error Diffusion ✓ Advanced Text Enhancement ✓ Advanced Text Enhancement II ✓ High-Speed Text Enhancement
  • Canon 3801B002 | User Manual - Page 103
    dpi, the [Image Quality] setting is enabled. Scanning Side Select which page side(s) to scan. [Simplex] Scan only the front (top) side of documents loaded at the feeder inlet. [Duplex] Scan both sides of documents. [Skip Blank Page] As each document page is scanned, its scanned image is judged as
  • Canon 3801B002 | User Manual - Page 104
    is set to [24-bit Color], and Scanning Side is set to [Duplex] all at the same time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority], or change the Scanning Side setting to [Simplex]. Image
  • Canon 3801B002 | User Manual - Page 105
    is set to [24-bit Color], and Scanning Side is set to [Duplex] all at the same time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority], or change the Scanning Side setting to [Simplex]. [Area
  • Canon 3801B002 | User Manual - Page 106
    to scan on a selected page size, and register non-standard document page sizes. The Scan Area dialog box is different for ISIS and TWAIN drivers: for the TWAIN driver, one of two dialog box types is displayed depending on the application program used. Scan Area Dialog Box (ISIS Driver) Area window
  • Canon 3801B002 | User Manual - Page 107
    Chapter 7 ISIS/TWAIN Driver Settings Scan Area Dialog Box (TWAIN Driver) This dialog box appears with application programs that display the [Scan] button in the Properties dialog box. Area window The Area window and [Preview] button are not displayed when using applications like the Job Registration
  • Canon 3801B002 | User Manual - Page 108
    is not possible on the extended version of the [Basic] tab sheet (P.7-4.) Preview Button (TWAIN driver only) Click the [Preview] button to scan one document page and display its preview image in the Area window. [Brightness] Tab Sheet On the [Brightness] tab sheet, you can adjust brightness and
  • Canon 3801B002 | User Manual - Page 109
    ISIS/TWAIN Driver Settings The availability of brightness and contrast settings are as follows according to the mode setting on the [Basic] tab sheet. Scanning ] Check Box If the contrast of the front and back of the document pages is different, select this to adjust only the contrast of the
  • Canon 3801B002 | User Manual - Page 110
    Chapter 7 ISIS/TWAIN Driver Settings [Gamma Settings] Dialog Box Use the [Gamma Settings] dialog box to adjust the gamma correction value. [Custom] Check Box Select this check box to
  • Canon 3801B002 | User Manual - Page 111
    Chapter 7 ISIS/TWAIN Driver Settings ☞ You can also move the gamma curve by dragging it with the mouse. [Freehand] The output value for a particular input value in the gamma
  • Canon 3801B002 | User Manual - Page 112
    according to the orientation of loaded documents and the selected rotation angle. Feeder documents: face up Image rotation (clockwise) 0° Flatbed documents: face down 90° 180° 270° [Reverse Image] Check Box (TWAIN driver only) The document is scanned with black and white reversed when
  • Canon 3801B002 | User Manual - Page 113
    Chapter 7 ISIS/TWAIN Driver Settings [Text Orientation Recognition] Check Box Select this check box to detect text orientation in scanned images, black spots from scanned images when scanning documents with punch holes. ☞ If punch holes are located within text or graphics in the document, they may
  • Canon 3801B002 | User Manual - Page 114
    the colors you specify may not match those processed. [Others] Tab Sheet The settings on the [Others] tab sheet are different for the ISIS and TWAIN drivers. Also, some settings may be disabled depending on the mode settings on the [Basic] tab sheet. Refer to "ModeDependent Function Limitations," on
  • Canon 3801B002 | User Manual - Page 115
    JPEG transfer, depending on instructions from the ISIS/TWAIN driver or application program. ☞ Uncompressed transfers output raw scanned image data, so when the image data is large, significant time may be required for transfer from the scanner to the computer. ☞ JPEG transfer is good for color and
  • Canon 3801B002 | User Manual - Page 116
    Chapter 7 ISIS/TWAIN Driver Settings Double Feed Detection This function stops document transport when double feeding of document pages is detected, and provides selection of the detection method to suit the documents to be scanned. [Detect by Length] This method of double feed detection is good for
  • Canon 3801B002 | User Manual - Page 117
    7 ISIS/TWAIN Driver Settings With the [Standard Feeding] Feeding Option With the [Automatic Feeding] or [Panel Feeding] Feeding Option [Auto] Each batch of documents is saved with different file names. [Panel] Document batches are separated when the [Batch Separation] button on the Scan Panel
  • Canon 3801B002 | User Manual - Page 118
    the optional barcode module is installed: click it to open the Barcode dialog box and make settings affecting barcode detection in documents. For details, see the ISIS/TWAIN driver Help, or contact your supplier. [Addon] Button This button opens the [Addon] dialog box, where you can make setting for
  • Canon 3801B002 | User Manual - Page 119
    7 ISIS/TWAIN Driver Settings Addon Dialog Box The [Addon] dialog box provides access to the following dialog boxes, where you can make setting for adding text or bitmap images to scanned document images. The [Addon] dialog box enables you to make setting for adding text or bitmap images to scanned
  • Canon 3801B002 | User Manual - Page 120
    Chapter 7 ISIS/TWAIN Driver Settings [Addon] Check Box Select this check box to apply text or bitmap images to scanned document images. The specified number of characters of the single counter will be inserted into scanned images. [Double counter with number of characters] abbreviation:
  • Canon 3801B002 | User Manual - Page 121
    Chapter 7 ISIS/TWAIN Driver Settings [Down arrow] abbreviation: Inserts a down arrow ( ) symbol. [Left arrow] abbreviation: Inserts a left arrow () symbol. [Right arrow] abbreviation: Inserts a right arrow ( ) symbol. ☞ Special text can
  • Canon 3801B002 | User Manual - Page 122
    Chapter 7 ISIS/TWAIN Driver Settings ☞ When add-on text is applied to an image, the size of the characters depends on the scan resolution. [Enable] Check Box Select this check box to enable application of bitmap images to scanned images. ☞ When adding a bitmap image, it is processed when scanning is
  • Canon 3801B002 | User Manual - Page 123
    Chapter 7 ISIS/TWAIN Driver Settings [Horizontal Offset] Enter the desired offset from the edge of the document feeder inlet. ☞ When applying an add-on to the front side, enter the offset from the left side of the feeder inlet. ☞ When applying an
  • Canon 3801B002 | User Manual - Page 124
    Chapter 7 ISIS/TWAIN Driver Settings Start Value Enter the start value for the counter. Increment This is the counter increment value. The counter increments by the value entered here. Increment Trigger Specifies the type of event that triggers a counter increment. [New File] (ISIS driver only) The
  • Canon 3801B002 | User Manual - Page 125
    Tool The Job Registration Tool is a TWAIN-compliant application program that installs with the ISIS/ TWAIN driver, and is started by the following procedure. 1 Click the Windows [Start] button, and click then [Programs] ([All Programs] for Windows XP) Æ [DR-6010C] Æ [Job Registration Tool]. The Job
  • Canon 3801B002 | User Manual - Page 126
    provides access to function setting dialog boxes. (See "[New/Editing] Dialog Box," on p. 8-4.) Job Registration Tool Dialog Box (p. 8-3) [Admin] Dialog Box (p. 8-8) [New/Editing] Dialog Box (p. 8-4) Scanner Settings Dialog Box Access Setting PDF/TIFF Settings 8-2
  • Canon 3801B002 | User Manual - Page 127
    the Job Registration Tool is started from the Programs menu. Job Button Settings List The displayed job buttons correspond to those on the scanner, showing their currently assigned settings. Clicking on the job buttons (a, b and c) opens the New/Editing dialog box. (See "[New/ Editing] Dialog Box
  • Canon 3801B002 | User Manual - Page 128
    appears as follows depending on the function settings registered to the Job buttons. Save as file Start Print Stop Launcher Attach to E-mail No scan job Settings Common to Each Function Job Number [No. 1 to No. 3] Shows the selected job button number. Settings are registered to the job button
  • Canon 3801B002 | User Manual - Page 129
    Windows "Event" function settings. (See "About Launcher," on p. 3-12.) Scanner setting When the "Save as file," "Print" or "Attach to E-mail" function is selected, Scanner settings are enabled, and you can press the [Setting] button to make scanner settings. ☞ Refer to Chapter 7, "ISIS/TWAIN Driver
  • Canon 3801B002 | User Manual - Page 130
    or change the scanner setting. [Setting] Button This button is enabled to display the corresponding setting dialog box when the [TIFF] or [PDF] file format is selected. TIFF Settings Dialog Box [Multi-tiff setting] Select the method for saving image files when scanning multi-page documents. • Select
  • Canon 3801B002 | User Manual - Page 131
    image quality may be slightly degraded. ☞ The Compression rate setting is enabled when the scanner is set to [256-level Gray] or [24-bit Color] mode. When [Black and White] or [Error Diffusion] binary image scanning mode is selected, file size depends on the content of the scanned document. Language
  • Canon 3801B002 | User Manual - Page 132
    format] Select whether to resize images for printing. • Select [Actual size] to print images the same size as their original documents. • Select [Fit to paper] if the scanned documents were larger than the printer paper, to resize the images to the printer paper size. Buttons [OK] button Click this
  • Canon 3801B002 | User Manual - Page 133
    total size of the files in the specified folder exceeds the specified limit. ☞ If a warning message appears, follow the instructions in the message to either continue scanning or change the save destination first. Monitor Job Dialog Settings [Show Monitor Dialog] Check Box Select this check box to
  • Canon 3801B002 | User Manual - Page 134
    Chapter 8 Job Registration Tool Settings ☞ The maximum size of attached files must not exceed the limit determined by the mail server. Ask your e-mail system administrator for the attachment size limit of the mail server. [Back Up / Restore] Settings [Back Up] Button Writes a backup file (*.reg) of
  • Canon 3801B002 | User Manual - Page 135
    for the DR-6010C ISIS/TWAIN driver. Refer to these examples when making ISIS/TWAIN driver settings. For descriptions of particular setting items, see "ISIS/TWAIN Driver Settings," on p. 7-1. Scanning Both Sides of Pages • To scanning both sides of pages Select [Duplex] for the Scanning Side setting
  • Canon 3801B002 | User Manual - Page 136
    ] is selected as the [Page Size]. (See "[Scan Area] Dialog Box," on p. 7-11.) With the TWAIN driver, load a document in the scanner and click the [Preview] button to scan one page.) The scanned image is displayed in the Area window so that you can adjust the scan area while viewing the preview image
  • Canon 3801B002 | User Manual - Page 137
    you press the Start button. After loading different-size documents, adjust the document guides or sort the pages before pressing the Start button to start scanning. • To create separate files for each batch of documents during continuous scanning (ISIS driver only.) Set the [Feeding Option] on the
  • Canon 3801B002 | User Manual - Page 138
    ] to either [Automatic Feeding] or [Panel Feeding], and scan each page. After scanning each page, the scanner returns to the waiting state. When [Automatic Feeding] is selected as the [Feeding Option], the scanner detects documents and starts scanning as they are loaded. When [Panel Feeding] is
  • Canon 3801B002 | User Manual - Page 139
    documents: face down • To rotate images to match document text Select [Text Orientation Recognition] on the [Image processing] tab sheet. The text orientation on each page is detected, and the scanned • To reverse black and white in scanned images (TWAIN driver only) Select [Reverse Image] on the
  • Canon 3801B002 | User Manual - Page 140
    sheet. The black areas around images are removed. (See "[Border Removal] Check Box," on p. 7-18.) • To remove the black spots from scanned images when scanning documents with punch holes Select the [Punch Hole Removal] check box on the [Image processing] tab sheet. The black spots from punch holes
  • Canon 3801B002 | User Manual - Page 141
    Panel The Prescan window provides adjustments for image brightness and contrast of the first document page before continuing scanning. The image settings as [User Preference] on the [Basic] tab sheet. When you want to recall your settings later, select the name of your registered user preferences,
  • Canon 3801B002 | User Manual - Page 142
    INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
User Manual
Please read this manual before operating this scanner.
After you finish reading this manual, store it in a safe
place for future reference.