Canon DR 7090C User Manual

Canon DR 7090C - imageFORMULA - Document Scanner Manual

Get Canon DR 7090C - imageFORMULA - Document Scanner PDF manuals and user guides
UPC - 013803100242
View all Canon DR 7090C manuals
Add to My Manuals
Save this manual to your list of manuals

Canon DR 7090C manual content summary:

  • Canon DR 7090C | User Manual - Page 1
    User Manual Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR 7090C | User Manual - Page 2
    if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to
  • Canon DR 7090C | User Manual - Page 3
    your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding return and recycling of WEEE products, please visit www.canon-europe.com/environment. (EEA: Norway, Iceland and
  • Canon DR 7090C | User Manual - Page 4
    basic scanner operating instructions extracted from the User Manual. User Manual (This Manual) This manual consists of two sections: Hardware and Software. The Hardware section provides general information about the scanner operational settings, maintenance, and troubleshooting. The Software section
  • Canon DR 7090C | User Manual - Page 5
    following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety. Describes displayed messages and troubleshooting solutions Chapter 7 Appendix Provides a list of specifications and support information ■ Software
  • Canon DR 7090C | User Manual - Page 6
    User Manual Hardware Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR 7090C | User Manual - Page 7
    Hardware Table of Contents Introduction iii Manuals for the Scanner iii Symbols Used in This Manual iv How This Manual is Organized iv Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions 1-2 Installation Location 1-2 Removing the Transportation Screw 1-2 Installing
  • Canon DR 7090C | User Manual - Page 8
    2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-11 Uninstalling the ISIS/TWAIN Driver 6-11 Chapter 7 Appendix 1. Specifications 7-2 Specifications for the Scanner 7-2 Options 7-3 Consumables 7-3 External Dimensions 7-4 2. Index 7-5
  • Canon DR 7090C | User Manual - Page 9
    Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions 1-2 Installation Location 1-2 Removing the Transportation Screw 1-2 Installing the Securing Braces 1-3 Power 1-3 Checking the Rear Cables 1-4 Opening and Closing the Feeder 1-4 Moving the Scanner 1-4 Handling 1-5
  • Canon DR 7090C | User Manual - Page 10
    Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. Installation Location The performance of this
  • Canon DR 7090C | User Manual - Page 11
    power cord can be disconnected easily in an emergency. ● If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information. 1-3
  • Canon DR 7090C | User Manual - Page 12
    Checking the Rear Cables Before connecting to the computer, make sure that cable connectors to are properly connected at the rear of the scanner. Chapter 1 Before You Start Using the Scanner ● Close the feeder carefully and slowly, taking care to avoid pinching your fingers. Opening and Closing
  • Canon DR 7090C | User Manual - Page 13
    ● Make sure to disconnect the interface cable and power cord when moving the scanner. If the scanner is carried with these items connected, the plugs and connectors may be damaged or cause the scanner to fall and result in personal injury or damage to the scanner. ■ Installing the Transportation
  • Canon DR 7090C | User Manual - Page 14
    , immediately turn the power switch OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative for further information. ■ Do not drop the scanner, or subject it to impact or strong shock. Should the scanner ever become damaged
  • Canon DR 7090C | User Manual - Page 15
    Chapter 1 Before You Start Using the Scanner ■ Turn OFF the power switch for safety when not using the scanner for a long period of time, such as overnight. Also, turn OFF the power switch, and disconnect the power cord from the power outlet for safety when the machine will not be used for an
  • Canon DR 7090C | User Manual - Page 16
    1 Before You Start Using the Scanner 2. Features The main features of the DR-7090C are described below. Scanner Features ● High-speed scanning The feeder supports scanning of LTR/A4-size documents at speeds up to 70 pages per minute. ● Single-pass duplex (two-side) scanning When scanning two-sided
  • Canon DR 7090C | User Manual - Page 17
    Detection Functions ● Auto Paper Size Detection The document page size is detected before scanning. Fixed-Size Scanning Auto-Size Detection Scanning ● Text Orientation Detection The text orientation on each page is detected, and the scanned image is rotated in 90-degree increments as necessary
  • Canon DR 7090C | User Manual - Page 18
    from a single scan pass. However, this function is only available when using CapturePerfect 3.0 (supplied with the scanner) or another application program that supports the MultiStream function. Document to be Scanned (150 dpi, Color) (300 dpi, Black & White) Two Types of Output Image ● Patchcode
  • Canon DR 7090C | User Manual - Page 19
    there is a document in the document feeder tray. (See p. 3-4.) When a paper jam occurs, this indicator flashes. (See p. 3-22.) d Slide Guide Adjust this guide to the marking on the document size label that indicates the applicable document size. (See p. 3-4.) e Document Feeder Tray Load documents to
  • Canon DR 7090C | User Manual - Page 20
    Rear Chapter 1 Before You Start Using the Scanner Operation Panel a Air Vents b USB Connector Connect a Hi-Speed USB 2.0 compatible USB cable here. (See p. 2-6.) c DIP Switches Configure these switches to specify the SCSI ID or terminator ON or OFF. (See p. 2-7.) d SCSI Connectors Connect a SCSI
  • Canon DR 7090C | User Manual - Page 21
    document and forwards the scanned image to the destination registered for the job. f New File Key This key is active for applications that support batch separation. This key lights when pressed or in accordance with the application's batch separation settings. Scanning the next document while this
  • Canon DR 7090C | User Manual - Page 22
    Chapter 1 Before You Start Using the Scanner 4. Optional Products The following options can be purchased and used on the DR-7090C, if they are necessary. Contact your sales representative. Stamp Unit The stamp unit affixes a stamp on document pages that are scanned using the feeder. The
  • Canon DR 7090C | User Manual - Page 23
    Chapter 2 Setup 1. Setup Procedures 2-2 2. Installation Requirements 2-3 3. Software Installation 2-4 About the Setup Menu 2-4 4. Connecting the Scanner to the Computer ....... 2-6 Interface Connector Locations 2-6 Using a USB Connection 2-6 Using a SCSI Connection 2-7 5. Turning the Power ON
  • Canon DR 7090C | User Manual - Page 24
    1. Setup Procedures Perform the following setup procedures to prepare the scanner for use. Step 1: Confirm the installation requirements. (See p. 2-3) Step 2: Install the Software. (See p. 2-4) Step 3: Connect the scanner to the computer. (See p. 2-6) Step 4: Turn the power ON (Scanner recognition
  • Canon DR 7090C | User Manual - Page 25
    bundled with the scanner or a Hi-Speed USB 2.0 compatible cable. • Note the following when using a SCSI card. - Make sure to follow the procedure in the manual for the SCSI card and the computer that you are using when installing a SCSI card in your computer. - The overall length of the SCSI cable
  • Canon DR 7090C | User Manual - Page 26
    Account Control" dialog box may appear. In this case, enter your login user password for Administrator privileges, and click [OK]. Hint See the Easy Start Guide for instructions on using the typical installation procedure. 2-4
  • Canon DR 7090C | User Manual - Page 27
    the selected software. ■ The Read Manual Screen From this screen you can select one of the supplied electronic manuals to read: the Easy Start Guide (a printed copy is also supplied), the Reference Guide, the User Manual (this manual), or the CapturePerfect 3.0 Operation Guide. Chapter 2 Setup 2-5
  • Canon DR 7090C | User Manual - Page 28
    Chapter 2 Setup 4. Connecting the Scanner to the Computer There are two methods for connecting the DR-7090C scanner to a computer: a USB connection to a standard USB port built in to the computer, or SCSI connection to a SCSI card installed in an expansion slot of the computer. Select the method
  • Canon DR 7090C | User Manual - Page 29
    Using a SCSI Connection IMPORTANT Make sure that the computer is turned OFF before connecting the SCSI cable. If the cable is connected while the computer is on, the scanner may not be properly recognized by the computer. 1. Shut down Windows and turn the computer's power OFF. 2. Connect the
  • Canon DR 7090C | User Manual - Page 30
    Set the terminator switch to ON. In such a connection, make sure that the terminators on all other SCSI devices are set to OFF. Terminator OFF Terminator ON
  • Canon DR 7090C | User Manual - Page 31
    Chapter 2 Setup 5. Turning the Power ON (Scanner Recognition) When you turn ON the computer and the scanner, the Windows Plug and Play function recognizes the scanner and automatically installs the required device driver. About the Power Switch The power switch is located on the scanner's side
  • Canon DR 7090C | User Manual - Page 32
    Hint • With Windows Vista, installation proceeds automatically regardless of the displayed "Check here for status" balloon help. You can click "Check here for status" to display the installation progress. Chapter 2 Setup • The DR-7090C device driver is installed in Device Manager under [Imaging
  • Canon DR 7090C | User Manual - Page 33
    Chapter 3 Basic Operation 1. Documents 3-2 Types of Documents 3-2 Feeder Capacity 3-3 2. Placing Documents onto the Scanner 3-4 Loading a Document into the Feeder 3-4 Positioning a Document on the Flatbed (Platen Glass 3-5 3. Document Feeding 3-8 Scan Procedure 3-8 4. Scanning 3-11 About
  • Canon DR 7090C | User Manual - Page 34
    Chapter 3 Basic Operation 1. Documents This section describes the various types of documents that can be scanned with the feeder. CAUTION Handle documents with care. Improper handling of paper can cause paper cuts or other personal injury. Types of Documents The following are the dimensions of
  • Canon DR 7090C | User Manual - Page 35
    • To avoid paper jams, damage to documents, and a scanner malfunction, do not feed the following types of paper. For such documents, scan one page at a time from the flatbed (platen glass). Wrinkled or creased paper Carbon-backed paper Curled paper Coated paper Torn paper Paper with clips or
  • Canon DR 7090C | User Manual - Page 36
    pointer is aligned with the corresponding paper size on the document size label. Slide Guide Document Set Indicator IMPORTANT Use both hands to adjust both the left and right slide guides. Adjusting only one slide guide can lead to a malfunction. 2. Align the edges of the document stack on a flat
  • Canon DR 7090C | User Manual - Page 37
    • When scanning NCR paper that is 11" x 17"/A3 or other large sizes, as well as paper that is very thin, the document may occasionally get caught in the paper eject mechanism. In this case, place an auxiliary sheet of paper in the document eject tray before scanning the document. Chapter 3 Basic
  • Canon DR 7090C | User Manual - Page 38
    2. Place the document onto the flatbed (platen glass) with the scanning side facing downwards. Chapter 3 Basic Operation 3. Slowly and carefully lower the feeder back down. With the scanning side of the document facing downwards, align its corner with the arrow mark in the upper left corner of the
  • Canon DR 7090C | User Manual - Page 39
    Hint Leave the feeder raised when scanning thick documents like books, or operate the feeder as shown in the procedure below. 1. Open the feeder. 2. While pressing on the bottom of the feeder a, pull the feeder down and forward b. Chapter 3 Basic Operation 3. Set the thick document or book on the
  • Canon DR 7090C | User Manual - Page 40
    be scanned. If there are no documents in the feeder, the flatbed will be scanned. ■ Standard Feeding To use the standard feeding mode, instruct the scanner to start from the application. 1. Select [Standard Feeding] in [Feeding Option] on the scanner settings screen. 2. Place the document onto the
  • Canon DR 7090C | User Manual - Page 41
    IMPORTANT See "Placing Documents onto the Scanner" on p. 3-4 for information about placing documents onto the scanner. 3. From the application you are using, execute the required command to start scanning. Scanning starts. 4. When scanning of the document is complete, the application goes into the
  • Canon DR 7090C | User Manual - Page 42
    ■ Automatic Feeding Automatic feeding can be used when feeding a document from the feeder. After you execute the scan start command from the application, the scanner starts scanning automatically whenever it detects a document loaded into the feeder. 1. Select [Automatic Feeding] in [Feeding Option]
  • Canon DR 7090C | User Manual - Page 43
    Chapter 3 Basic Operation 4. Scanning Scanning operations can be controlled by a scanning application program such as the CapturePerfect 3.0 software included with the scanner, or directly from the control panel of the DR-7090C, using the Job Function. This section describes the Job Function and
  • Canon DR 7090C | User Manual - Page 44
    scanning of the document is complete, press the Stop key to exit the Job Mode. Hint If the Job Mode is not operating correctly, see "Troubleshooting" on p. 6-5. 3-12
  • Canon DR 7090C | User Manual - Page 45
    ■ Setting the Events Function The Job function will not function unless [DR7090C Job Tool] is specified for the scanner's Events function in Windows. Before using the Job function, perform the following procedure to configure the scanner's event settings. 1. Click the [Start] button, then select [
  • Canon DR 7090C | User Manual - Page 46
    . Select the desired scan mode from the Scan menu to perform scanning. For more information on CapturePerfect 3.0, refer to the CapturePerfect 3.0 Operation Guide. 6. Clear all the check boxes under [Send to this application] except for the [DR-7090C Job Tool] check box. 7. Click [Apply]. IMPORTANT
  • Canon DR 7090C | User Manual - Page 47
    for using the Scan Batch to File function is described here as an example. For details, refer to the CapturePerfect 3.0 Operation Guide. 1. From the Windows task bar, click [Start] ➔ click [All Programs] ➔ [CapturePerfect 3.0] ➔ [CapturePerfect 3.0]. ba Hint The following two scan jobs are already
  • Canon DR 7090C | User Manual - Page 48
    2. From the [Scan] menu, select [Select Scanner]. Chapter 3 Basic Operation 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Scan Batch to File]. The [Select Scanner] dialog box opens. 3. Select [Canon DR-7090C] and click [Settings]. The [Scan Batch to File Setting]
  • Canon DR 7090C | User Manual - Page 49
    on the available settings in the [Scan Batch to File Setting] dialog box, refer to the CapturePerfect 3.0 Operation Guide. • If a Feed Option other than [Standard Feeding] or [Manual Feeding] is selected, once you have started scanning, each document placed in the Document Feed Tray is scanned, and
  • Canon DR 7090C | User Manual - Page 50
    11. When the [Continue Scanning] dialog box appears, verify that a document is loaded, and click either [Continue Scanning] or [Stop Scanning]. Hint If Use Continue Scanning dialog in the [Scan] menu is not checked, scanning finishes without displaying the Continue Scanning dialog box. 12. When
  • Canon DR 7090C | User Manual - Page 51
    on which a special pattern is printed that allows file separation without interrupting scan processes. Patchcode sheets can be used with applications that support patchcode file separation. When the patchcode sheet is scanned and the pattern is recognized, the document pages that follow can be saved
  • Canon DR 7090C | User Manual - Page 52
    How to Use Patchcode Sheets This section describes how to use patchcode sheets with CapturePerfect 3.0. 1. Print the patchcode sheets on a printer. IMPORTANT • Print (at original size) PATCH T (A4) and PATCH II (A4) sheets on A4 paper, or PATCH T (LTR) and PATCH II (LTR) on LTR paper. • The scanner
  • Canon DR 7090C | User Manual - Page 53
    Chapter 3 Basic Operation 6. Count Only Mode In Count Only Mode, document pages are sent through the feeder in order to count them. The documents are not scanned in this mode. Operations for Count Only Mode can be performed without a computer. 1. Press the Menu key and display "Count Only Mode"
  • Canon DR 7090C | User Manual - Page 54
    lever, and then slowly raise the cover until it stops. 3. Confirm the location of the paper jam. 4. If the document is jammed under the feeder guide, grasp the tab inside the scanner to open the feeder
  • Canon DR 7090C | User Manual - Page 55
    feeds jammed paper into the document eject tray. After feeding the paper, raise the document feeder tray and remove the paper. 6. Close the feeder guide. CAUTION Take care to avoid pinching your fingers when closing the feeder cover. 8. Open the feeder. CAUTION Take care to avoid pinching your
  • Canon DR 7090C | User Manual - Page 56
    What to check: Is the document size or thickness outside the range supported by the feeder, or is the document paper of substandard quality? clean them. (See p. 5-6.) If the rollers are worn, contact your service representative to have them replaced. CAUTION Lower the feeder slowly, taking care to
  • Canon DR 7090C | User Manual - Page 57
    Chapter 4 User Modes 1. About the User Modes 4-2 User Mode Functions 4-2 How to Set the User Modes 4-3
  • Canon DR 7090C | User Manual - Page 58
    Chapter 4 User Modes 1. About the User Modes You can configure the scanner settings with the user modes described below. User Mode Functions User mode functions are as follows: ■ Count Only Mode Co u n t On l y Mo d e ON [ OFF ] ON: Counts the number of pages in a document using stand-alone
  • Canon DR 7090C | User Manual - Page 59
    Chapter 4 User Modes ■ Setting SCSI Transfer Speed SCS I Sp e e d [ 20 ] 10 5 Set the maximum value for synchronous transfer speed for the SCSI interface. 20: 20 Mbyte/sec (Ultra SCSI) (default) 10: 10 Mbyte/sec (First SCSI) 5: 5 Mbyte/sec (non-synchronous) If the scanner does not operate
  • Canon DR 7090C | User Manual - Page 60
    Chapter 5 Maintenance 1. Changing the Stamp Cartridge 5-2 2. Daily Cleaning 5-4 About the Cleaning Cloth and Cleaning Paper .....5-4 Cleaning the Main Unit 5-4 Cleaning the Flatbed (Platen Glass) and Pressure Board 5-5 Cleaning the Feeder 5-6 Cleaning the Power Plug 5-12
  • Canon DR 7090C | User Manual - Page 61
    stamp mark becomes smudged or faint. Contact your sales reprentative or service representative to purchase a new stamp cartridge. 1. Open the Open the feeder guide, and then open the inner cover. The feeder guide has a green tab, while the inner cover located under the feeder guide has a light
  • Canon DR 7090C | User Manual - Page 62
    5. Close the feeder guide and inner cover. CAUTION Take care to avoid pinching your fingers when closing the feeder guide and inner cover. 6. Close the feeder cover. CAUTION Take care to avoid pinching your fingers when closing the feeder cover. 5-3 Chapter 5 Maintenance
  • Canon DR 7090C | User Manual - Page 63
    Chapter 5 Maintenance 2. Daily Cleaning To maintain high-quality scanning, you should periodically clean the following: • Main unit • Flatbed (Platen glass) • Pressure Board • Feeder CAUTION • Before you clean the scanner, turn OFF the scanner and computer and disconnect the power cord from the
  • Canon DR 7090C | User Manual - Page 64
    Cleaning the Flatbed (Platen Glass) and Pressure Board A dirty flatbed (platen glass) or pressure board can cause soiling of scanned images, or document size detection errors. Clean the flatbed (platen glass) and pressure board periodically. 1. Open the feeder. Chapter 5 Maintenance 2. Wipe the
  • Canon DR 7090C | User Manual - Page 65
    3. Slowly and carefully close the feeder. Chapter 5 Maintenance Cleaning the Feeder Without periodic cleaning, a problem may be caused on the scanned image or the document may become soiled. Clean the feeder periodically. 1. Open the feeder cover. Operate the opening lever,
  • Canon DR 7090C | User Manual - Page 66
    3. Wipe the 13 rollers on the feeder guide with a cloth moistened with plain water and thoroughly wrung , dry cloth. 4. Grasp the tab in the front to open the feeder guide. 6. Wipe the four rollers inside the feeder guide with a cloth moistened with plain water and thoroughly wrung out. Next, wipe
  • Canon DR 7090C | User Manual - Page 67
    . 9. Open the feeder. Chapter 5 Maintenance CAUTION Take care to avoid pinching your fingers when closing the feeder guide. 8. Close the feeder cover. 10. Wipe the feeder roller (white) and platen roller (black) with a cloth moistened with plain water and thoroughly wrung out. Next,
  • Canon DR 7090C | User Manual - Page 68
    IMPORTANT When you open the feeder cover and turn the dial located in the front, the platen roller rotates. When cleaning the platen roller, rotate the roller slowly while wiping it. Chapter 5 Maintenance 12. Remove the scanning area cleaning tool from inside the cover. Dial 11. Pull the lever on
  • Canon DR 7090C | User Manual - Page 69
    14. Attach the cleaning paper to the scanning area cleaning tool. Chapter 5 Maintenance 16. Wipe the platen roller located behind the inner cover with a cloth moistened with plain water and thoroughly wrung out. Next, wipe the roller with a soft, dry cloth. IMPORTANT When cleaning the platen roller
  • Canon DR 7090C | User Manual - Page 70
    18. Close the inner cover. Chapter 5 Maintenance 20. Close the cover for the feeder's scanning area. CAUTION Take care to avoid pinching your fingers when closing the cover. 19. Remove the cleaning paper from the scanning area cleaning tool, and place the cleaning tool inside the cover. CAUTION
  • Canon DR 7090C | User Manual - Page 71
    22. Slowly and carefully lower the feeder back down. Chapter 5 Maintenance Cleaning the Power Plug If you leave the power plug connected to the power outlet for a long period of time, dust may accumulate at the power outlet, and cause a fire or electrical shock. Clean the power plug periodically.
  • Canon DR 7090C | User Manual - Page 72
    Chapter 6 Practical Examples 1. Messages 6-2 Status Display 6-2 Error Messages 6-3 2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-11 Uninstalling the ISIS/TWAIN Driver 6-11
  • Canon DR 7090C | User Manual - Page 73
    1. Messages There are two types of display panel messages: "status indicator messages" and "error messages" that appear when the scanner encounters a problem. Status Display The following messages appear on the display panel to indicate the scanner's operating state: ■ Count Only Mode Co u n t On
  • Canon DR 7090C | User Manual - Page 74
    of different sizes, set the mixed document mode to ON in the scanner settings to prevent this message from appearing. ■ Call for Service Ca l l f o r Se r v i ce Ex x x x x x x Error Code: E2020001 Cause: The transportation screws are still installed on the scanner. Solution: Turn the scanner OFF
  • Canon DR 7090C | User Manual - Page 75
    Internal scanner error. Solution: Turn the power OFF, and restart the scanner. If this does not solve the problem, make a note of the error code and contact your Canon service representative. ■ Single-Pass OFF S i n g l e - Pa s s OFF Cause: This appears when the scanner is restarted after the "Call
  • Canon DR 7090C | User Manual - Page 76
    Troubleshooting This section describes the problems that may occur during use of the scanner and how to solve them. Trouble Categories The following trouble It you cannot resolve a problem, contact your local authorized Canon dealer or your service representative. Problem and Solution ■ The Scanner
  • Canon DR 7090C | User Manual - Page 77
    local authorized Canon dealer or service representative for more information. Cause The scanner does not support the USB cable. Solution Use not be properly recognized by the PC. If this does not solve the problem, consider the following possible causes: Cause The SCSI card is not compatible with
  • Canon DR 7090C | User Manual - Page 78
    the PC's USB interface support only Full-Speed USB 1.1? ✔ Is the USB cable you are using the one that was supplied with the scanner (Hi-Speed USB 2.0 compliant)? ✔ Is a USB 1.1-compliant device connected to the USB hub at the same time? If this does not solve the problem, consider the following
  • Canon DR 7090C | User Manual - Page 79
    dealer or service representative. If this does not solve the problem, consider the following possible problems and causes: Problem Cause driver settings may be incorrect, or your application may not support certain scanner functions. Problem Cause Solution The scanned image is too dark (or faint
  • Canon DR 7090C | User Manual - Page 80
    the document guides to match the width of your document. Problem Cause service representative. Chapter 6 Practical Examples Problem Problem Cause Solution The scanned image is abnormal in some applications. A function not supported by the application was used. Some applications do not support
  • Canon DR 7090C | User Manual - Page 81
    to Japanese in the user mode settings. Set the panel display to English in the user mode settings. (See "About the User Modes" on p. 4-2.) Problem Cause Solution The panel display is dark. The brightness setting for the display panel needs adjustment. Adjust the Display Contrast in the user mode
  • Canon DR 7090C | User Manual - Page 82
    Chapter 6 Practical Examples 3. Uninstalling the Software Some scanner malfunctions can be resolved by reinstalling the software. Before reinstalling the software, make sure to completely uninstall any previous installation first. Uninstalling the ISIS/TWAIN Driver The following procedure uses
  • Canon DR 7090C | User Manual - Page 83
    The file-deletion confirmation screen appears. 4. Click [Yes] to proceed with uninstallation. 5. When uninstallation is finished, click [Finish]. Chapter 6 Practical Examples 6-12
  • Canon DR 7090C | User Manual - Page 84
    Chapter 7 Appendix 1. Specifications 7-2 Specifications for the Scanner 7-2 Options 7-3 Consumables 7-3 External Dimensions 7-4 2. Index 7-5
  • Canon DR 7090C | User Manual - Page 85
    Chapter 7 Appendix 1. Specifications Specifications for the Scanner Type Desktop ADF/flatbed scanner Document Size Width: 5.5" to 11.7" (139.7 mm to 298.1 mm) Length: 5.0" to 17.0" (128 mm to 431.8 mm) (Normal Mode) 5.0" to 24.8" (128 mm to 630 mm) (Long Document Mode) Document Thickness Black-and-
  • Canon DR 7090C | User Manual - Page 86
    °C) Humidity: 25% to 80% RH • You can use the functions noted above if the software supports them. • They may not work depending on your computer's capabilities and the software you are using and consumables, contact your sales representative or your service representative. 7-3 Chapter 7 Appendix
  • Canon DR 7090C | User Manual - Page 87
    External Dimensions Chapter 7 Appendix 23.7" (602 mm) (16.4" (714 mm)) 12.4" (314 mm) 5.9" (150 mm) 24.3" (618 mm) 12.5" (317 mm) 14.8" (377 mm) 23.1" (586 mm) 1.3" (32 mm) 7-4
  • Canon DR 7090C | User Manual - Page 88
    (Platen Glass 1-11 H Handling 1-5 I Installation Location 1-2 Installation Requirements 2-3 J Job Function 3-11 Job Keys 1-13 Job Mode 3-12 Job Registration Tool 3-11 M Manuals for the Scanner iii Menu Key 1-12 Moving the Scanner 1-4 N Names and Functions of Parts 1-11 New File Key 1-13
  • Canon DR 7090C | User Manual - Page 89
    1-11, 2-9 Practical Examples 6-1 Pressure Board 1-11 R Read Manual 2-5 S Scanning area cleaning tool 1-11 SCSI Cards 2-3 SCSI Connection 1-12 Setup 2-2 Setup Menu 2-4 Single-Pass Duplex 4-3 Slide Guide 1-11 Software Installation 2-4 Specifications 7-2 Stamp Cartridge 5-2 Stamp Unit
  • Canon DR 7090C | User Manual - Page 90
    User Manual Software Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR 7090C | User Manual - Page 91
    Table of Contents Chapter 8 ISIS/TWAIN Driver Settings 1. Before Use 8-2 2. ISIS/TWAIN Driver Settings Dialog Boxes .......8-4 Basic Setup Dialog Box 8-5 Scan Area Dialog Box 8-9 Orientation Settings Dialog Box 8-11 Advanced Settings Dialog Box 8-12 Gamma Settings Dialog Box 8-15 Other
  • Canon DR 7090C | User Manual - Page 92
    Chapter 8 ISIS/TWAIN Driver Settings 1. Before Use 8-2 2. ISIS/TWAIN Driver Settings Dialog Boxes....... 8-4 Basic Setup Dialog Box 8-5 Scan Area Dialog Box 8-9 Orientation Settings Dialog Box 8-11 Advanced Settings Dialog Box 8-12 Gamma Settings Dialog Box 8-15 Other Settings Dialog Box 8-16
  • Canon DR 7090C | User Manual - Page 93
    /TWAIN Driver Settings 1. Before Use An application program that supports the ISIS or TWAIN driver is required to use the depends on the application program being used, refer to your application's user's manual as needed to select the scanner. IMPORTANT • When the conditions for scanning
  • Canon DR 7090C | User Manual - Page 94
    2. Click [Select Scanner] in the [Scan] menu. Chapter 8 ISIS/TWAIN Driver Settings 6. Click [Scanner Setting] in the [Scan] menu. The [Select Scanner] dialog box appears. 3. Select [Canon DR-7090C] ➔ click the [Settings] button. The settings dialog box for the ISIS driver appears. If [Canon DR-
  • Canon DR 7090C | User Manual - Page 95
    Chapter 8 ISIS/TWAIN Driver Settings 2. ISIS/TWAIN Driver Settings Dialog Boxes This settings dialog boxes for the ISIS/TWAIN driver consist of the Basic Setup dialog box, Advanced Settings dialog box, and Other Settings dialog box. The contents of the settings dialog boxes depend on whether the
  • Canon DR 7090C | User Manual - Page 96
    Basic Setup Dialog Box This dialog box allows you to make settings for the basic scanning conditions. The items you can set differ depending on the application program you use. Make the settings as needed for the screen actually displayed. ■ Types of Basic Setup Dialog Box There are the following
  • Canon DR 7090C | User Manual - Page 97
    ■ Settings of Basic Setup Dialog Box You can configure the following settings in the Basic Setup dialog box. User Preference Click [Save] to open the [Save User Preference] dialog box. The [Save User Preference] dialog box saves the current settings under an assigned name. You can select the name of
  • Canon DR 7090C | User Manual - Page 98
    brightness setting is incorrect - When the Custom setting is selected in the Gamma Settings dialog box • Some application programs do not support auto-page-size detection. Dots per inch Select the scanning resolution. Hint Higher resolutions provide clearer images, but produce larger files. Chapter
  • Canon DR 7090C | User Manual - Page 99
    [Simplex] Scans the front side of documents. [Duplex] Scan both sides of documents. [Skip Blank Page] As each document page is scanned, whether the scanned image is blank is judged, and if blank, the image is not saved. • When [Scan Options] is set to [Scan Single Page] for the TWAIN driver, [Duplex
  • Canon DR 7090C | User Manual - Page 100
    Chapter 8 ISIS/TWAIN Driver Settings Buttons [Area] button Open the [Scan Area] dialog box to specify the area to scan. (See "Scan Area Dialog Box" on p. 8-9.) The [Area] button is not displayed if the application program provides its own function to specify the scan area. [More] Button Click this
  • Canon DR 7090C | User Manual - Page 101
    The Area window and [Preview] button are not displayed when using application programs like Job Registration Tool that display the [OK] button in the settings dialog box. Page Size Select the size of the document to scan. This setting is linked to the [Page Size] setting in the Basic Setup dialog
  • Canon DR 7090C | User Manual - Page 102
    [OK] button Click this button to accept changes and close the dialog box. [Cancel] button Click this button to reject changes and close the dialog box. [Help] button Click this button to display help for this dialog box. Orientation Settings Dialog Box This dialog box appears when you click the [
  • Canon DR 7090C | User Manual - Page 103
    the ISIS driver is accessed from a scanner setting or scanning dialog box belonging to an ISIS-compatible application program. It contains settings that are not supported in the settings dialog box belonging to the application program. 8-12
  • Canon DR 7090C | User Manual - Page 104
    Chapter 8 ISIS/TWAIN Driver Settings Hint For details on [Text Enhanced Mode], [Detect Page Size], [Skip Blank Page], and [Deskew], see the descriptions for the following settings. • [Text Enhanced Mode] ➔ [Mode] • [Detect Page Size] ➔ [Page Size] • [Skip Blank Page] ➔ [Scanning Side] • [Deskew] ➔
  • Canon DR 7090C | User Manual - Page 105
    Chapter 8 ISIS/TWAIN Driver Settings Apply first page size to next pages When [Scan Ahead] is selected in the settings of the application program, this setting is enabled and the document size of the first page detected with auto detection is applied to the next pages. This minimizes the reduction
  • Canon DR 7090C | User Manual - Page 106
    Gamma Settings Dialog Box This dialog box appears when you click the [Gamma] button in the Advanced Settings dialog box. This dialog box allows you to change the settings for the gamma correction value. Chapter 8 ISIS/TWAIN Driver Settings • The gamma correction value, gamma curve graph, and sample
  • Canon DR 7090C | User Manual - Page 107
    Chapter 8 ISIS/TWAIN Driver Settings Hint Gamma table data (*.pxg files) consists of 258 lines of text used to create the desired image data. Refer to "Gamma Table Files" in the ISIS/TWAIN driver Help for details. Buttons [OK] button Click this button to accept changes and close the Basic Setup
  • Canon DR 7090C | User Manual - Page 108
    Chapter 8 ISIS/TWAIN Driver Settings [Automatic Feeding] Once scanning is started from an application program, whenever a document is loaded in the feeder, the scanner automatically detects it and begins scanning. To finish scanning, press the stop button on the scanner or stop scanning from the
  • Canon DR 7090C | User Manual - Page 109
    Patchcode Orientation (ISIS Driver Only) This function is enabled when batch separation is set to [Patchcode]. Set the orientation to match that of the patchcode of the patchcode sheet. Chapter 8 ISIS/TWAIN Driver Settings Prescan Prescan and display the first document page in the Prescan window
  • Canon DR 7090C | User Manual - Page 110
    Chapter 9 Job Registration Tool Settings 1. Before Use 9-2 Job Function 9-2 Starting Job Registration Tool 9-2 2. Job Registration Tool 9-3 3. Settings Dialog Boxes 9-4 [New/Editing] Dialog Box 9-4 [Admin] Dialog Box 9-9
  • Canon DR 7090C | User Manual - Page 111
    Chapter 9 Job Registration Tool Settings 1. Before Use Job Registration Tool is an application program for registering jobs that can be executed from the Job key on the control panel. This chapter describes the settings for Job Registration Tool. For details on Job Registration Tool, see "About the
  • Canon DR 7090C | User Manual - Page 112
    Chapter 9 Job Registration Tool Settings 2. Job Registration Tool Job Registration Tool consists of the main window below and the [New/Editing] and [Admin] dialog boxes. For details on the dialog boxes, see the description of each dialog box. • Selecting [Delete] displays a confirmation message. •
  • Canon DR 7090C | User Manual - Page 113
    Chapter 9 Job Registration Tool Settings 3. Settings Dialog Boxes The settings dialog boxes of Job Registration Tool include the [New/Editing] dialog box and [Admin] dialog box. For details, see the description of each dialog box. [New/Editing] Dialog Box In the [New/Editing] dialog box, you can
  • Canon DR 7090C | User Manual - Page 114
    Chapter 9 Job Registration Tool Settings Hint The setting items that appear in the [New/Editing] dialog box vary depending on the [Function] setting. (See "[Function]" on p. 9-5.) Function Save as file Setting Item Print Send by E-Mail Launcher No. ✔ ✔ ✔ ✔ Job title ✔ ✔ ✔ ✔ Scanner
  • Canon DR 7090C | User Manual - Page 115
    Chapter 9 Job Registration Tool Settings Scanner Setting Click the [Setting] button to configure the scanner settings. [Mail address] Enter the e-mail address of the recipient for the scanned image files. [Add] button To send to multiple recipients, click the [Add] button. The following dialog box
  • Canon DR 7090C | User Manual - Page 116
    Chapter 9 Job Registration Tool Settings Hint When a mode other than [256-level Gray] or [24-bit Color] is selected, an error is displayed if [JPEG] is selected when you click the [OK] button. If the error appears, change the file format or scanner mode. [Setting] Button This button is enabled to
  • Canon DR 7090C | User Manual - Page 117
    box is selected, a standard level of JPEG compression is applied. Hint If your application program does not support the above compression formats, you may be unable to open scanned image files. In this case, disable . • Select [User settings] to enable the slider and set the quality manually. 9-8
  • Canon DR 7090C | User Manual - Page 118
    [Admin] Dialog Box The [Admin] dialog box allows you to configure settings for monitoring the storage folder for images, settings for the mail server and settings for backing up job data. Chapter 9 Job Registration Tool Settings ■ Capacity Warning Settings The capacity warning settings allow you to
  • Canon DR 7090C | User Manual - Page 119
    is started if the total size of the files in the specified folder exceeds the specified limit. • If a warning message appears, follow the instructions in the message to either continue scanning or change the save destination first. ■ Show Monitor Dialog Setting [Show Monitor Dialog] check box Check
  • Canon DR 7090C | User Manual - Page 120
    ■ Job Back Up Settings Set this function to back up the registered jobs when the same job is to be executed in a different environment, such as occurs when multiple users log on to Windows or when multiple scanners are used. [Back Up] Button Write a backup file (*.reg) of registered job data to any
  • Canon DR 7090C | User Manual - Page 121
    Chapter 10 Practical Examples 1. About Basic Condition Settings 10-2 Confirming Basic Conditions for Scanning..........10-2 2. Practical Examples 10-4 Scanning Documents of Unregistered Page Sizes 10-4 Specifying Scanning Area 10-5 Configuring Scanner Settings According to Purpose 10-5
  • Canon DR 7090C | User Manual - Page 122
    Chapter 10 Practical Examples 1. About Basic Condition Settings This section provides an overview of the basic setting items that are the minimum requirements when configuring the scanner settings. For details on settings, see Chapter 8 "ISIS/TWAIN Driver Settings". Confirming Basic Conditions
  • Canon DR 7090C | User Manual - Page 123
    Scanning Side Select which page side(s) to scan. Hint • To scan using the flatbed, set the scanning side to [Flatbed] or [Auto]. • If the scanning side is set to [Auto], documents placed in the feeder tray will be scanned. If there are no documents in the feeder tray, the flatbed will be scanned. •
  • Canon DR 7090C | User Manual - Page 124
    box. 2. Set [Page Size] to [Auto-detection] in the Basic Setup dialog box. IMPORTANT • Long Document Mode is not available if it is not supported by the application program. • When scanning a long document, load and scan the pages of the document one at time. • Some scanning mode and resolution
  • Canon DR 7090C | User Manual - Page 125
    ■ Registering of non-standard page sizes You can register a non-standard page size that has not been registered as a page size by naming and registering it as a custom page size in the [Page Size] setting of the Scan Area dialog box, which is opened from the [Area] button in the Basic Setup dialog
  • Canon DR 7090C | User Manual - Page 126
    ■ When you want to enhance a particular color Select the color (red, blue, or green) to be enhanced in [Color drop-out] in the Advanced Settings dialog box, and that color will be enhanced. Chapter 10 Practical Examples ■ When you want to reverse the black and white in scanned images (TWAIN driver
  • Canon DR 7090C | User Manual - Page 127
    ■ When you want to remove the black spots from scanned images when scanning documents with punch holes Select the [Punch Hole Removal] check box in the Advanced Settings dialog box. The black spots from punch holes in documents are removed from scanned images. (See p. 8-14.) ■ When you want to match
  • Canon DR 7090C | User Manual - Page 128
    Chapter 10 Practical Examples Hint Images are rotated as follows according to the orientation of the loaded document and the selected angle. Flatbed Document: Face Down Feeder Document: Face Up Document Orientation Image Rotation (Clockwise) 0 degrees 90 degrees 180 degrees 270 degrees Output
  • Canon DR 7090C | User Manual - Page 129
    CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
User Manual