Canon PIXMA iP5200 iP5200 Easy Setup Instructions - Page 1
Canon PIXMA iP5200 Manual
View all Canon PIXMA iP5200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
1 Unpack the Printer 2 Prepare the Printer Start Here Easy Setup Instructions 3 Install the Print Head 4 Install the Ink Tanks Series Photo Printer 5 Connect the Printer and Load Paper 1 Carefully remove all items from the box. PIXMA iP5200 Photo Printer Documentation and Software Kit PIXMA iP5200 Print Head Power Cord CLI-8BK Black CLI-8Y Yellow PGI-5BK Black CLI-8M Magenta CLI-8C Cyan Ink Tanks 2 Remove the tape from the printer. 1 Before turning on the printer, open the top cover and remove the protective material and tape from the printer as shown. The tape position is subject to change. CAUTION: Be sure to remove the protective material before you turn on the printer. 2 Close the top cover. Plug the power cord into the back of the printer and connect the other end to a power outlet. Press the POWER button. The printer will initialize. Wait until the POWER lamp displays a steady green light. POWER Button POWER Lamp 3 Open the front cover. Raise the top cover. Lower the inner cover. NOTE: Push the open button above the front cover. The front cover automatically opens. Open Button Inner Cover Top Cover 1 Remove the print head from its package. Tear at notch to open CAUTION: There might be some transparent or light blue ink on the inside of the bag the print head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. 2 Remove the orange protective cap from the print head. 1 Peel back the orange tab completely and remove the plastic wrapper from the Cyan Ink Tank (CLI-8C). 2 Twist off and discard the orange protective cap located on the bottom of the ink tank. IMPORTANT: Do not touch the electrical contacts. NOTE: · To avoid spilling ink, never press on the sides of an ink tank. · Do not touch the open ink port once the protective cap is removed, as this may prevent the ink from being ejected properly. Protective Cap IMPORTANT: Be sure the printer is off before continuing, or the computer will attempt to install the printer driver before the printer is ready. 1 TURN THE PRINTER OFF. 2 Connect one end of the USB cable to the computer, the other to the appropriate USB port on the printer. NOTE: The iP5200 Photo Printer is equipped with USB 2.0 Hi-Speed port. If your PC does not support USB 2.0 Hi-Speed, or if any noncertified USB 2.0 cable or driver is used for the connection, the printer will operate at a lower speed provided under USB 1.1. USB Port USB Cable USB Port CAUTION: There might be some transparent or light blue ink on the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. NOTE: · Do not touch the print head nozzles and the electrical contacts. · Do not attempt to reattach the protective cap once it has been removed. Print Head Nozzles Electrical Contacts Electrical Contacts Ink Port 3 Insert the ink tank into the rightmost slot. Press the mark on the ink tank until it clicks into place and then its lamp lights red. click 3 Firmly raise the print head lock lever. Ink Tank Lamp 4 Insert the remaining four ink tanks into their assigned slots. Ensure that ink tank lamps light red. Refer to the color guide on the print head lock lever. USB Cable 3 Pinch the paper guide and slide it to the left. Load a few sheets of blank paper into the auto sheet feeder, align the paper with the cover guide, then slide the paper guide toward the left edge of the paper. Auto Sheet Feeder Print Side Front Cover 4 The print head holder automatically moves to the center. Write down the serial number located inside the printer. You will need this to register your products. 4 Slide the print head into the holder. The print head will rest at a slight angle. 5 Close (a) the inner cover and then (b) the top cover. Lift open the paper support and extend the paper output tray. IMPORTANT: Be sure to close the inner cover completely, or the paper will not feed properly. Paper Support (a) Inner Cover (b) Top Cover Paper Guide Cover Guide IMPORTANT: Print Head Alignment (Step 6) requires that letter size paper is loaded in the Auto Sheet Feeder (top paper feeder). Serial Number Location IMPORTANT: If the top cover is left open for more than 10 minutes, the print head holder moves to the right. Close and reopen the top cover to return the holder to the center. 5 Lower the print head lock lever carefully and press it down. Paper Output Tray NOTE: · The printer will perform a print head cleaning. Wait until the POWER lamp displays a steady green light before proceeding. · If the ALARM lamp still flashes orange even after the printer has stopped making operating noises, an ink tank may not be installed properly. Open the top cover and make sure that the ink tanks are installed in the correct order directed on the label. Continue with Step 6 on side two.