Casio WV200A-1AV Operation Manual - Page 3

Operation Guide 3140 Signal Reception Troubleshooting Check the following points whenever you experience problems with calibration signal reception. Problem Probable Cause What you should do Cannot perform • The watch is not in the Timekeeping Mode. • Enter the Timekeeping Mode manual receive. • Your current Home City is not one of the and try again. following city codes: • Select one of the cities to the HNL, ANC, YVR, LAX, YEA, DEN, MEX, left as your Home City. YWG, CHI, MIA, YTO, NYC, YHZ, YYT, LIS, • Stop the countdown timer LON, MAD, PAR, ROM, BER, STO, ATH, or and try again. MOW. • The countdown timer is running. Auto receive is • You changed the time setting manually. • Perform manual signal turned on, but the • The watch was not in the Timekeeping or receive or wait until the next Level 3 receiving World Time Mode, or you performed some auto signal receive operation indicator does button operation during the auto receive is performed. not appear on the operation. • Perform manual signal display. • Even if receive is successful, the Level 3 receive or wait until the next receiving indicator disappears every day auto signal receive operation when the first auto receive operation of the is performed. day is performed. • Check to make sure the • Time data (hour, minutes, seconds) only was watch is in a location where received during the last receive operation. it can receive the signal. The Level 3 receiving indicator appears only when time data and date data (year, month, day) are both received. Time setting is incorrect following signal reception. • If the time is one hour off, the DST setting • Change the DST setting to may be incorrect. Auto DST. • The Home City code setting is not correct for • Select the correct Home City the area where you are using the watch. code. • For further information, see "Important!" and "Radio-controlled Atomic Timekeeping Precautions". World Time City code UTC offset The World Time Mode shows you the current time in 48 cities (29 time zones) around the world. • If the current time shown for a city is wrong, check your Home City time settings and make the necessary changes. • All of the operations in this section are performed in the World Time Mode, which you enter by pressing C. Current time in selected city Timekeeping Mode time To view the time in another city While in the World Time Mode, press D to scroll eastward through the city codes (time zones). • For full information on city codes, see the "City Code Table". To toggle a city code time between Standard Time and Daylight Saving Time DST indicator 1. In the World Time Mode, use D to display the city code (time zone) whose Standard Time/Daylight Saving Time setting you want to change. 2. Hold down A to toggle Daylight Saving Time (DST indicator displayed) and Standard Time (DST indicator not displayed). • The DST indicator will appear whenever you display a city code for which Daylight Saving Time is turned on. • Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected. Countdown Timer Timekeeping Mode time (Hour : Minutes Seconds) You can set the countdown timer within a range of one to 60 minutes. An alarm sounds when the countdown reaches zero. • All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C . Minutes Seconds To set the countdown start time 1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting screen. • If the countdown start time is not displayed, use the procedure under "To use the countdown timer" to display it. 2. While a setting is flashing, use D (+) and B (-) to change it. 3. Press A to exit the setting screen. To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. • When the end of the countdown is reached, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is reset automatically to its starting value after the alarm stops. • Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown. • To stop a countdown operation completely, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value. • Calibration signal reception is disabled while a countdown timer operation is in progress. Stopwatch Timekeeping Mode time (Hour : Minutes Seconds) Minutes Seconds 1/100 second The stopwatch lets you measure elapsed time, split times, and two finishes. • The display range of the stopwatch is 59 minutes, 59.99 seconds. • The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. • Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. • The stopwatch measurement operation continues even if you exit the Stopwatch Mode. • All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. To measure times with the stopwatch Elapsed Time Start Split Time Stop Re-start Stop Clear Start Two Finishes Split (SPL displayed) Split release Stop Clear Start Split First runner finishes. Display time of first runner. Stop Second runner finishes. Split release Display time of second runner. Clear Alarm Timekeeping Mode time (Hour : Minutes Seconds) Alarm on indicator After you set (and turn on) the daily alarm, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep for about one second every hour on the hour. • All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C. Alarm time (Hour : Minutes) Hourly time signal on indicator To set the alarm time 1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. • This automatically turns on the alarm. 2. Press C to move the flashing between the hour and minute settings. 3. While a setting is flashing, use D (+) and B (-) to change it. • When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator). 4. Press A to exit the setting screen. Alarm Operation The alarm sounds at the preset time for about 10 seconds (in all modes), or until you stop it by pressing any button. To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn the daily alarm and the Hourly Time Signal on and off In the Alarm Mode, press D to cycle through the settings shown below. Alarm On Indicator / Hourly Time Signal On Indicator Alarm Off Signal Off Alarm On Signal Off Alarm Off Signal On Alarm On Signal On • The alarm on indicator and the Hourly Time Signal on indicator are shown on the display in all modes while these functions are turned on. 3